Great, thanks! This is really a very useful feature.
Regards, Bernhard > On 24 Jan 2016, at 22:14, Jon Neal <[email protected]> wrote: > > Hmmm, I think I know where to look for this. I'll check it out later tonight. > > Thanks for the heads up Bernhard! > > Jon > > On Sun, Jan 24, 2016 at 4:09 PM Bernhard Stegmaier <[email protected] > <mailto:[email protected]>> wrote: > One minor thing I just found, don’t know if it is intended this way: > > I have some IC on my board, most of its connections already routed. > I swapped one pin of it to a different net in eeschema, exported the netlist. > In pcbnew I imported the netlist (Footprint Selection = Reference, Exchange > Footprint = Change, everything else = Delete). > After closing the netlist dialog the IC was in move mode just like if it was > a new component. > > I wouldn’t have expected this, since it is not a new component. > > > Regards, > Bernhard > > > > On 10 Jan 2016, at 22:28, Chris Pavlina <[email protected] > > <mailto:[email protected]>> wrote: > > > > Patch committed in 6439. I like this a lot, it doesn't seem to break > > anything*, and it's fairly minimal in reach. Thank you! > > > > *I also can't see any possible way it could have caused the reported > > library issue, that's surely unrelated. > > > > -- > > Chris > > > > On Tue, Jan 05, 2016 at 09:10:04PM +0000, Jon Neal wrote: > >> here is the patch: > >> https://github.com/reportingsjr/kicad-source-mirror/commit/dd96d250321b17e0f8691d5623ea202f8762023c.patch > >> > >> <https://github.com/reportingsjr/kicad-source-mirror/commit/dd96d250321b17e0f8691d5623ea202f8762023c.patch> > >> > >> On Tue, Jan 5, 2016 at 3:03 PM Jon Neal <[email protected] > >> <mailto:[email protected]>> wrote: > >> > >>> If no one has any complaints or suggestions then this patch is ready to be > >>> included. > >>> > >>> I can generate a git diff with commit, author etc if needed, just let me > >>> know. > >>> > >>> Also, I accidentally sent this to Maciej only earlier: > >>> Simon Richter mentioned that doing a swap was a cleaner method of doing it > >>> for a variety of reasons. It doesn't really have to be done that way, just > >>> following his advice. > >>> > >>> Jon > >>> > >>> On Tue, Jan 5, 2016 at 10:55 AM Andy Peters <[email protected] > >>> <mailto:[email protected]>> wrote: > >>> > >>>> > >>>>> On Jan 4, 2016, at 6:59 PM, Jon Neal <[email protected] > >>>>> <mailto:[email protected]>> wrote: > >>>>> > >>>>> I asked about this a while back and got a little bit of feedback, I now > >>>> have a patch for people to try. > >>>>> > >>>>> What this does is when you import a netlist (in GAL only though) it > >>>> automatically spreads out all newly added footprints and it places them > >>>> all > >>>> in "selection + move" mode. So basically you import, close the import > >>>> window, and immediately click wherever to plonk down the new footprints. > >>>>> > >>>>> I want to know if people like this method of importing (I think it is > >>>> nicer than piling all of the footprints on top of each other wherever). > >>>> > >>>> > >>>> YES! > >>>> > >>>> -a > >>>> > >>>> > >>>> > >>>> _______________________________________________ > >>>> Mailing list: https://launchpad.net/~kicad-developers > >>>> <https://launchpad.net/~kicad-developers> > >>>> Post to : [email protected] > >>>> <mailto:[email protected]> > >>>> Unsubscribe : https://launchpad.net/~kicad-developers > >>>> <https://launchpad.net/~kicad-developers> > >>>> More help : https://help.launchpad.net/ListHelp > >>>> <https://help.launchpad.net/ListHelp> > >>>> > >>> > > > >> _______________________________________________ > >> Mailing list: https://launchpad.net/~kicad-developers > >> <https://launchpad.net/~kicad-developers> > >> Post to : [email protected] > >> <mailto:[email protected]> > >> Unsubscribe : https://launchpad.net/~kicad-developers > >> <https://launchpad.net/~kicad-developers> > >> More help : https://help.launchpad.net/ListHelp > >> <https://help.launchpad.net/ListHelp> > > > > > > _______________________________________________ > > Mailing list: https://launchpad.net/~kicad-developers > > <https://launchpad.net/~kicad-developers> > > Post to : [email protected] > > <mailto:[email protected]> > > Unsubscribe : https://launchpad.net/~kicad-developers > > <https://launchpad.net/~kicad-developers> > > More help : https://help.launchpad.net/ListHelp > > <https://help.launchpad.net/ListHelp> >
_______________________________________________ Mailing list: https://launchpad.net/~kicad-developers Post to : [email protected] Unsubscribe : https://launchpad.net/~kicad-developers More help : https://help.launchpad.net/ListHelp
