Jeremy,

with new madwifi, it seems a little bit more complicated. You will have wifi0 as the place holder for each wireless NIC (previously) and then you need to use some tool (hopefully Eric built together with modules) to create ath0 out of wifi0 and then apply the settings on ath0.

So basically when you do 'ip addr' you should see both wifi0 and ath0 but when 'iwconfig' you see ath0 having wireless settings.

In fact I am just reading the readme file and will try to see if I can use them later.

Also your NIC could be still new and not sure if it is supported.



----- Original Message ----- From: "Jeremy Tourville" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]>; <[email protected]>
Sent: Friday, October 28, 2005 10:03 PM
Subject: Re: [leaf-user] Madwifi Drivers for Bering uClibc 2.3 rc1- 3rd try


>Hello Jeremy,

Attached you will find the drivers from today's snapshot. I hope they work!

Eric



Well, I tried the new drivers you compiled with no luck. Is my card still not supported by the new code drop? I have a MIMO card. It is a D Link DWL-G520M. It has the AR5513 processor/chipset. Here is some diagnostic output for everyone. I have snipped some output to only include relevant info.

firewall# cat /proc/pci
PCI devices found:
  Bus  0, device  11, function  0:
   Class 0200: PCI device 168c:0020 (rev 1).
     IRQ 9.
     Master Capable.  Latency=80.  Min Gnt=10.Max Lat=28.
     Non-prefetchable 32 bit memory at 0xfcfe0000 [0xfcffffff].


firewall# dmesg
wlan: 0.8.4.2 (Atheros/multi-bss)
wlan: mac acl policy registered
ath_hal: 0.9.15.1 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
ath_rate_onoe: 1.0
ath_pci: 0.9.4.5 (Atheros/multi-bss)

firewall# more modules
# /etc/modules: kernel modules to load at boot time.
#
# Wireless AP
wlan
wlan_acl
wlan_tkip
wlan_xauth
ath_hal
ath_rate_onoe
ath_pci

firewall# lsmod
Module                  Size  Used by    Tainted: P
ath_pci                56820   0 (unused)
ath_rate_onoe           2900   0 [ath_pci]
ath_hal               179184   0 [ath_pci]
wlan_xauth               216   0 (unused)
wlan_tkip               8368   0 (unused)
wlan_acl                1784   0 (unused)
wlan 116530 0 [ath_pci ath_rate_onoe wlan_xauth wlan_tkip wlan_acl]
softdog                 1360   1
ipt_state                272  17
ipt_helper               400   0 (unused)
ipt_conntrack            692   0
ipt_REDIRECT             480   0 (unused)
ipt_MASQUERADE          1024   2
ip_nat_irc              1704   0 (unused)
ip_nat_ftp              2152   0 (unused)
iptable_nat 14332 3 [ipt_REDIRECT ipt_MASQUERADE ip_nat_irc ip_nat_ftp]
ip_conntrack_irc        2484   1
ip_conntrack_ftp        3132   1
ip_conntrack 16516 2 [ipt_state ipt_helper ipt_conntrack ipt_REDIRECT ipt_MASQUERADE ip_nat_irc ip_nat_ftp iptable_nat ip_conntrack_irc ip_conntrack_ftp]
3c59x                  23768   2
3c515                  11052   1
isofs                  15732   0 (unused)
ide-detect               132   0 (unused)
ide-cd                 26748   0
ide-disk               11308   0
ide-core               80476   0 [ide-detect ide-cd ide-disk]
cdrom                  25344   0 [ide-cd]


firewall# ip address show
1: lo: <LOOPBACK,UP> mtu 16436 qdisc noqueue
   link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
   inet 127.0.0.1/8 scope host lo
2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop
   link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000
   link/ether 00:10:4b:6e:ef:9a brd ff:ff:ff:ff:ff:ff
   inet 70.224.209.172/24 brd 70.224.209.255 scope global eth0
4: eth1: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000
   link/ether 00:a0:24:37:d4:c0 brd ff:ff:ff:ff:ff:ff
   inet 192.168.1.254/24 brd 192.168.1.255 scope global eth1
5: eth2: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000
   link/ether 00:a0:24:75:b2:50 brd ff:ff:ff:ff:ff:ff
   inet 192.168.2.100/24 brd 192.168.2.255 scope global eth2

# /etc/network/interfaces -- configuration file for LEAF network
# Step 7 (optional): configure wireless AP (Madwifi)
auto ath0
iface ath0 inet static
       address 192.168.3.1
       netmask 255.255.255.0
       broadcast 192.168.3.255
       wireless-mode master
       wireless rate 54M
       wireless-essid default
       up /sbin/iwpriv/ ath0 mode 3

Thanks all in advance for your help!

Jeremy




-------------------------------------------------------
This SF.Net email is sponsored by the JBoss Inc.
Get Certified Today * Register for a JBoss Training Course
Free Certification Exam for All Training Attendees Through End of 2005
Visit http://www.jboss.com/services/certification for more information
------------------------------------------------------------------------
leaf-user mailing list: [email protected]
https://lists.sourceforge.net/lists/listinfo/leaf-user
Support Request -- http://leaf-project.org/



-------------------------------------------------------
This SF.Net email is sponsored by the JBoss Inc.
Get Certified Today * Register for a JBoss Training Course
Free Certification Exam for All Training Attendees Through End of 2005
Visit http://www.jboss.com/services/certification for more information
------------------------------------------------------------------------
leaf-user mailing list: [email protected]
https://lists.sourceforge.net/lists/listinfo/leaf-user
Support Request -- http://leaf-project.org/

Reply via email to