Hi James, I never have seen an error like this... Could you try again with a clean package? (which version of dnsmasq are you using?)
Eric > Hi, > > > Yes, we have eth0, 1 and 2. > > > eth0 = net (/28 eth1 = loc eth2 = dmz > > I get the same error with or without the interface and no-dhcp-interface > lines (I put them I to make sure that wasn't the problem, loc has it's own > Win2K DNS server as part of the domain) > > > Regards, > > > James. > > > -----Original Message----- > From: Eric Spakman [mailto:[EMAIL PROTECTED] > Sent: 13 July 2006 14:56 > To: James Neave > Cc: [email protected] > Subject: Re: [leaf-user] dnsmasq will not startq > > > Hi James, > > > The only thing that I see in the config what could cause this are the > following two entries: interface=eth2 no-dhcp-interface=eth2 > > Do you have an interface eth2? > > > The last line shouldn't be even necessary, you don't have the internal > dnsmasq dhcp server enabled. > > Eric > > >> >> >> Getting this when I try to start dnsmasq: >> >> >> >> dnsmasq: failed to find list of interfaces: Cannot assign requested >> address >> >> The only reference I can find to this error is something about IPv6. >> >> >> >> Does anybody know what's going on? >> >> >> >> Thanks, >> >> >> >> James. >> >> >> >> dnsmasq.conf: >> >> >> >> # Configuration file for dnsmasq. >> # >> # Format is one option per line, legal options are the same >> # as the long options legal on the command line. See >> # "/usr/sbin/dnsmasq --help" or "man 8 dnsmasq" for details. >> >> >> >> # The following two options make you a better netizen, since they >> # tell dnsmasq to filter out queries which the public DNS cannot >> # answer, and which load the servers (especially the root servers) >> # uneccessarily. If you have a dial-on-demand link they also stop >> # these requests from bringing up the link uneccessarily. >> >> >> >> # Never forward plain names (without a dot or domain part) >> domain-needed # Never forward addresses in the non-routed address > spaces. >> bogus-priv >> >> >> # Uncomment this to filter useless windows-originated DNS requests >> # which can trigger dial-on-demand links needlessly. >> # Note that (amongst other things) this blocks all SRV requests, >> # so don't use it if you use eg Kerberos. >> # This option only affects forwarding, SRV records originating for >> # dnsmasq (via srv-host= lines) are not suppressed by it. >> #filterwin2k >> >> >> >> # Change this line if you want dns to get its upstream servers from >> # somewhere other that /etc/resolv.conf >> #resolv-file> >> >> >> # By default, dnsmasq will send queries to any of the upstream >> # servers it knows about and tries to favour servers to are known >> # to be up. Uncommenting this forces dnsmasq to try each query >> # with each server strictly in the order they appear in >> # /etc/resolv.conf >> #strict-order >> >> >> >> # If you don't want dnsmasq to read /etc/resolv.conf or any other >> # file, getting its servers for this file instead (see below), then >> # uncomment this >> no-resolv >> >> # If you don't want dnsmasq to poll /etc/resolv.conf or other resolv >> # files for changes and re-read them then uncomment this. >> #no-poll >> >> >> >> # Add other name servers here, with domain specs if they are for >> # non-public domains. >> server=158.152.1.58 server=158.152.1.43 #server=/localnet/192.168.27.3 >> >> >> # Add local-only domains here, queries in these domains are answered >> # from /etc/hosts or DHCP only. >> #local=/localnet/ >> >> >> >> # Add domains which you want to force to an IP address here. >> # The example below send any host in doubleclick.net to a local >> # webserver. >> #address=/doubleclick.net/127.0.0.1 >> >> >> >> # If you want dnsmasq to change uid and gid to something other >> # than the default, edit the following lines. >> #user> #group> >> >> >> # If you want dnsmasq to listen for DHCP and DNS requests only on >> # specified interfaces (and the loopback) give the name of the >> # interface (eg eth0) here. >> # Repeat the line for more than one interface. >> interface=eth2 # Or you can specify which interface _not_ to listen on >> #except-interface> # Or which to listen on by address (remember to >> include 127.0.0.1 if # you use this.) >> #listen-address> # If you want dnsmasq to provide only DNS service on an >> interface, # configure it as shown above, and then use the following >> line to # disable DHCP on it. >> no-dhcp-interface=eth2 >> >> # On systems which support it, dnsmasq binds the wildcard address, >> # even when it is listening on only some interfaces. It then discards >> # requests that it shouldn't reply to. This has the advantage of >> # working even when interfaces come and go and change address. If you >> # want dnsmasq to really bind only the interfaces it is listening on, >> # uncomment this option. About the only time you may need this is when >> # running another nameserver on the same machine. >> #bind-interfaces >> >> >> >> # If you don't want dnsmasq to read /etc/hosts, uncomment the >> # following line. >> #no-hosts >> # or if you want it to read another file, as well as /etc/hosts, use >> # this. >> #addn-hosts=/etc/banner_add_hosts >> >> >> >> # Set this (and domain: see below) if you want to have a domain >> # automatically added to simple names in a hosts-file. >> #expand-hosts >> >> >> >> # Set the domain for dnsmasq. this is optional, but if it is set, it >> # does the following things. >> # 1) Allows DHCP hosts to have fully qualified domain names, as long >> # as the domain part matches this setting. >> # 2) Sets the "domain" DHCP option thereby potentially setting the >> # domain of all systems configured by DHCP >> # 3) Provides the domain part for "expand-hosts" >> domain=private.network >> >> # Uncomment this to enable the integrated DHCP server, you need >> # to supply the range of addresses available for lease and optionally >> # a lease time. If you have more than one network, you will need to >> # repeat this for each network on which you want to supply DHCP >> # service. >> #dhcp-range=192.168.1.1,192.168.1.199,12h >> >> >> >> # This is an example of a DHCP range where the netmask is given. This >> # is needed for networks we reach the dnsmasq DHCP server via a relay >> # agent. If you don't know what a DHCP relay agent is, you probably >> # don't need to worry about this. >> #dhcp-range=192.168.0.50,192.168.0.150,255.255.255.0,12h >> >> >> >> # This is an example of a DHCP range with a network-id, so that >> # some DHCP options may be set only for this network. >> #dhcp-range=red,192.168.0.50,192.168.0.150 >> >> >> >> # Supply parameters for specified hosts using DHCP. There are lots >> # of valid alternatives, so we will give examples of each. Note that >> # IP addresses DO NOT have to be in the range given above, they just >> # need to be on the same network. The order of the parameters in these >> # do not matter, it's permissble to give name,adddress and MAC in any >> order >> >> # Always allocate the host with ethernet address 11:22:33:44:55:66 >> # The IP address 192.168.0.60 >> #dhcp-host=11:22:33:44:55:66,192.168.0.60 >> >> >> >> # Always set the name of the host with hardware address >> # 11:22:33:44:55:66 to be "fred" >> #dhcp-host=11:22:33:44:55:66,fred >> >> >> >> # Always give the host with ethernet address 11:22:33:44:55:66 >> # the name fred and IP address 192.168.0.60 and lease time 45 minutes >> #dhcp-host=11:22:33:44:55:66,fred,192.168.0.60,45m >> >> >> >> # Give the machine which says it's name is "bert" IP address >> # 192.168.0.70 and an infinite lease >> #dhcp-host=bert,192.168.0.70,infinite >> >> >> >> # Always give the host with client identifier 01:02:02:04 >> # the IP address 192.168.0.60 >> #dhcp-host=id:01:02:02:04,192.168.0.60 >> >> >> >> # Always give the host with client identifier "marjorie" >> # the IP address 192.168.0.60 >> #dhcp-host=id:marjorie,192.168.0.60 >> >> >> >> # Enable the address given for "judge" in /etc/hosts >> # to be given to a machine presenting the name "judge" when >> # it asks for a DHCP lease. >> #dhcp-host=judge >> >> >> >> # Never offer DHCP service to a machine whose ethernet >> # address is 11:22:33:44:55:66 >> #dhcp-host=11:22:33:44:55:66,ignore >> >> >> >> # Ignore any client-id presented by the machine with ethernet >> # address 11:22:33:44:55:66. This is useful to prevent a machine >> # being treated differently when running under different OS's or >> # between PXE boot and OS boot. >> #dhcp-host=11:22:33:44:55:66,id:* >> >> >> >> # Send extra options which are tagged as "red" to >> # the machine with ethernet address 11:22:33:44:55:66 >> #dhcp-host=11:22:33:44:55:66,net:red >> >> >> >> # Send extra options which are tagged as "red" to >> # any machine with ethernet address starting 11:22:33: >> #dhcp-host=11:22:33:*:*:*,net:red >> >> >> >> # Send extra options which are tagged as "red" to any machine whose >> # DHCP vendorclass string includes the substring "Linux" >> #dhcp-vendorclass=red,Linux >> >> >> >> # Send extra options which are tagged as "red" to any machine one >> # of whose DHCP userclass strings includes the substring "accounts" >> #dhcp-userclass=red,accounts >> >> >> >> # If this line is uncommented, dnsmasq will read /etc/ethers and act >> # on the ethernet-address/IP pairs found there just as if they had >> # been given as --dhcp-host options. Useful if you keep >> # MAC-address/host mappings there for other purposes. >> #read-ethers >> >> >> >> # Send options to hosts which ask for a DHCP lease. >> # See RFC 2132 for details of available options. >> # Note that all the common settings, such as netmask and >> # broadcast address, DNS server and default route, are given >> # sane defaults by dnsmasq. You very likely will not need any >> # any dhcp-options. If you use Windows clients and Samba, there >> # are some options which are recommended, they are detailed at the >> # end of this section. >> # For reference, the common options are: >> # subnet mask - 1 >> # default router - 3 >> # DNS server - 6 >> # broadcast address - 28 >> >> >> >> # Set the NTP time server addresses to 192.168.0.4 and 10.10.0.5 >> #dhcp-option=42,192.168.0.4,10.10.0.5 >> >> >> >> # Set the NTP time server address to be the same machine as >> # is running dnsmasq >> #dhcp-option=42,0.0.0.0 >> >> >> >> # Set the NIS domain name to "welly" >> #dhcp-option=40,welly >> >> >> >> # Set the default time-to-live to 50 >> #dhcp-option=23,50 >> >> >> >> # Set the "all subnets are local" flag >> #dhcp-option=27,1 >> >> >> >> # Send the etherboot magic flag and then etherboot options (a string). >> #dhcp-option=128,e4:45:74:68:00:00 >> #dhcp-option=129,NIC=eepro100 >> >> >> >> # Specify an option which will only be sent to the "red" network >> # (see dhcp-range for the declaration of the "red" network) >> #dhcp-option=red,42,192.168.1.1 >> >> >> >> # The following DHCP options set up dnsmasq in the same way as is >> specified # for the ISC dhcpcd in # >> >> > http://www.samba.org/samba/ftp/docs/textdocs/DHCP-Server-Configuration.t > >> xt # adapted for a typical dnsmasq installation where the host running # >> dnsmasq is also the host running samba. # you may want to uncomment them >> if you use Windows clients and Samba. #dhcp-option=19,0 # >> option ip-forwarding off #dhcp-option=44,0.0.0.0 # set >> netbios-over-TCP/IP nameserver(s) > aka >> WINS server(s) >> #dhcp-option=45,0.0.0.0 # netbios datagram distribution server >> #dhcp-option=46,8 # netbios node type >> #dhcp-option=47 # empty netbios scope. >> >> >> >> # Send RFC-3397 DNS domain search DHCP option. WARNING: Your DHCP >> > client >> # probably doesn't support this...... >> #dhcp-option=119,eng.apple.com,marketing.apple.com >> >> >> >> # Send encapsulated vendor-class specific options. The vendor-class >> # is sent as DHCP option 60, and all the options marked with the >> # vendor class are send encapsulated in DHCP option 43. The meaning of >> # the options is defined by the vendor-class. This example sets the >> # mtftp address to 0.0.0.0 for PXEClients >> #dhcp-option=vendor:PXEClient,1,0.0.0.0 >> >> >> >> # Set the boot filename and tftpd server name and address >> # for BOOTP. You will only need this is you want to >> # boot machines over the network. >> #dhcp-boot=/var/ftpd/pxelinux.0,boothost,192.168.0.3 >> >> >> >> # Set the limit on DHCP leases, the default is 150 >> #dhcp-lease-max=150 >> >> >> >> # The DHCP server needs somewhere on disk to keep its lease database. >> # This defaults to a sane location, but if you want to change it, use >> # the line below. >> #dhcp-leasefile=/var/lib/misc/dnsmasq.leases >> >> >> >> # Set the DHCP server to authoritative mode. In this mode it will >> > barge >> in # and take over the lease for any client which broadcasts on the >> network, # whether it has a record of the lease or not. This avoids > long >> timeouts # when a machine wakes up on a new network. DO NOT enable > this if >> there's # the slighest chance that you might end up accidentally >> configuring a DHCP # server for your campus/company accidentally. The >> ISC server uses the >> same # the same option, and this URL provides more information: # >> http://www.isc.org/index.pl?/sw/dhcp/authoritative.php >> #dhcp-authoritative >> >> >> >> # Set the cachesize here. >> #cache-size=150 >> >> >> >> # If you want to disable negative caching, uncomment this. >> #no-negcache >> >> >> >> # Normally responses which come form /etc/hosts and the DHCP lease >> # file have Time-To-Live set as zero, which conventionally means >> # do not cache further. If you are happy to trade lower load on the >> # server for potentially stale date, you can set a time-to-live (in >> # seconds) here. >> #local-ttl> >> >> >> # If you want dnsmasq to detect attempts by Verisign to send queries >> # to unregistered .com and .net hosts to its sitefinder service and >> # have dnsmasq instead return the correct NXDOMAIN response, uncomment >> # this line. You can add similar lines to do the same for other >> # registries which have implemented wildcard A records. >> #bogus-nxdomain=64.94.110.11 >> >> >> >> # If you want to fix up DNS results from upstream servers, use the >> # alias option. This only works for IPv4. >> # This alias makes a result of 1.2.3.4 appear as 5.6.7.8 >> #alias=1.2.3.4,5.6.7.8 >> # and this maps 1.2.3.x to 5.6.7.x >> #alias=1.2.3.0,5.6.7.0,255.255.255.0 >> >> >> >> >> # Change these lines if you want dnsmasq to serve MX records. >> >> >> >> # Return an MX record named "maildomain.com" with target >> # servermachine.com and preference 50 >> #mx-host=maildomain.com,servermachine.com,50 >> >> >> >> # Set the default target for MX records created using the localmx >> option. #mx-target=servermachine.com >> >> >> # Return an MX record pointing to the mx-target for all local >> # machines. >> #localmx >> >> >> >> # Return an MX record pointing to itself for all local machines. >> #selfmx >> >> >> >> # Change the following lines if you want dnsmasq to serve SRV >> # records. These are useful if you want to serve ldap requests for >> # Active Directory and other windows-originated DNS requests. >> # See RFC 2782. >> # You may add multiple srv-host lines. >> # The fields are <name>,<target>,<port>,<priority>,<weight> >> # If the domain part if missing from the name (so that is just has the >> # service and protocol sections) then the domain given by the domain> # >> config option is used. (Note that expand-hosts does not need to be # set >> for this to work.) >> >> >> # A SRV record sending LDAP for the example.com domain to >> # ldapserver.example.com port 289 >> #srv-host=_ldap._tcp.example.com,ldapserver.example.com,389 >> >> >> >> # A SRV record sending LDAP for the example.com domain to >> # ldapserver.example.com port 289 (using domain=) >> #domain=example.com >> #srv-host=_ldap._tcp,ldapserver.example.com,389 >> >> >> >> # Two SRV records for LDAP, each with different priorities >> #srv-host=_ldap._tcp.example.com,ldapserver.example.com,389,1 >> #srv-host=_ldap._tcp.example.com,ldapserver.example.com,389,2 >> >> >> >> # A SRV record indicating that there is no LDAP server for the domain >> # example.com >> #srv-host=_ldap._tcp.example.com >> >> >> >> >> # Change the following lines to enable dnsmasq to serve TXT records. >> # These are used for things like SPF and zeroconf. (Note that the >> # domain-name expansion done for SRV records _does_not >> # occur for TXT records.) >> >> >> >> #Example SPF. >> #txt-record=example.com,v=spf1 a -all >> >> >> >> #Example zeroconf >> #txt-record=_http._tcp.example.com,name=value,paper=A4 >> >> >> >> >> # For debugging purposes, log each DNS query as it passes through >> # dnsmasq. >> #log-queries >> >> >> >> # Include a another lot of configuration options. >> #conf-file=/etc/dnsmasq.more.conf >> >> >> >> The information in this email is confidential and may be legally >> privileged. It is intended solely for the addressee. Access to this >> email by anyone else is unauthorised. >> >> If you are not the intended recipient, any disclosure, copying, >> distribution or any action taken or omitted to be taken in reliance on > it >> is prohibited and may be unlawful. >> >> The contents of an attachment to this email may contain software >> > viruses >> that could damage your own computer systems. Whilst The Spur Group of >> Companies has taken every precaution to minimise the risk, we cannot >> accept liability for any damage that you sustain as a result of > software >> viruses. >> >> >> >> > ------------------------------------------------------------------------ > - > >> Using Tomcat but need to do more? Need to support web services, >> security? Get stuff done quickly with pre-integrated technology to > make >> your job easier Download IBM WebSphere Application Server v.1.0.1 > based on >> Apache Geronimo >> >> > http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642 > >> > ------------------------------------------------------------------------ > >> leaf-user mailing list: [email protected] >> https://lists.sourceforge.net/lists/listinfo/leaf-user >> Support Request -- http://leaf-project.org/ >> >> >> > > > > The information in this email is confidential and may be legally > privileged. It is intended solely for the addressee. Access to this > email by anyone else is unauthorised. > > If you are not the intended recipient, any disclosure, copying, > distribution or any action taken or omitted to be taken in reliance on it > is prohibited and may be unlawful. > > The contents of an attachment to this email may contain software viruses > that could damage your own computer systems. Whilst The Spur Group of > Companies has taken every precaution to minimise the risk, we cannot > accept liability for any damage that you sustain as a result of software > viruses. > > ------------------------------------------------------------------------- Using Tomcat but need to do more? Need to support web services, security? Get stuff done quickly with pre-integrated technology to make your job easier Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642 ------------------------------------------------------------------------ leaf-user mailing list: [email protected] https://lists.sourceforge.net/lists/listinfo/leaf-user Support Request -- http://leaf-project.org/
