Hi James, You can see the version number with "lrpkg -l" or cat /var/lib/lrpkg/dnsmasq.version
Eric > Hi, > > > I don't know, where do you find the version number? > I shall try again with a new package, but not today (too much work to > do) Some time next week. > > > Thanks, > > > James. > > > -----Original Message----- > From: Eric Spakman [mailto:[EMAIL PROTECTED] > Sent: 13 July 2006 19:31 > To: James Neave > Cc: [email protected] > Subject: Re: [leaf-user] dnsmasq will not startq > > > Hi James, > > > I never have seen an error like this... Could you try again with a clean > package? (which version of dnsmasq are you using?) > > Eric > > >> Hi, >> >> >> >> Yes, we have eth0, 1 and 2. >> >> >> >> eth0 = net (/28 eth1 = loc eth2 = dmz >> >> I get the same error with or without the interface and >> > no-dhcp-interface >> lines (I put them I to make sure that wasn't the problem, loc has it's > own >> Win2K DNS server as part of the domain) >> >> >> >> Regards, >> >> >> >> James. >> >> >> >> -----Original Message----- >> From: Eric Spakman [mailto:[EMAIL PROTECTED] >> Sent: 13 July 2006 14:56 >> To: James Neave >> Cc: [email protected] >> Subject: Re: [leaf-user] dnsmasq will not startq >> >> >> >> Hi James, >> >> >> >> The only thing that I see in the config what could cause this are the >> following two entries: interface=eth2 no-dhcp-interface=eth2 >> >> Do you have an interface eth2? >> >> >> >> The last line shouldn't be even necessary, you don't have the internal >> dnsmasq dhcp server enabled. >> >> Eric >> >> >> >>> >>> >>> Getting this when I try to start dnsmasq: >>> >>> >>> >>> >>> dnsmasq: failed to find list of interfaces: Cannot assign requested >>> address >>> >>> The only reference I can find to this error is something about IPv6. >>> >>> >>> >>> >>> Does anybody know what's going on? >>> >>> >>> >>> >>> Thanks, >>> >>> >>> >>> >>> James. >>> >>> >>> >>> >>> dnsmasq.conf: >>> >>> >>> >>> >>> # Configuration file for dnsmasq. >>> # >>> # Format is one option per line, legal options are the same >>> # as the long options legal on the command line. See >>> # "/usr/sbin/dnsmasq --help" or "man 8 dnsmasq" for details. >>> >>> >>> >>> >>> # The following two options make you a better netizen, since they >>> # tell dnsmasq to filter out queries which the public DNS cannot >>> # answer, and which load the servers (especially the root servers) >>> # uneccessarily. If you have a dial-on-demand link they also stop >>> # these requests from bringing up the link uneccessarily. >>> >>> >>> >>> >>> # Never forward plain names (without a dot or domain part) >>> domain-needed # Never forward addresses in the non-routed address >> spaces. >>> bogus-priv >>> >>> >>> # Uncomment this to filter useless windows-originated DNS requests >>> # which can trigger dial-on-demand links needlessly. >>> # Note that (amongst other things) this blocks all SRV requests, >>> # so don't use it if you use eg Kerberos. >>> # This option only affects forwarding, SRV records originating for >>> # dnsmasq (via srv-host= lines) are not suppressed by it. >>> #filterwin2k >>> >>> >>> >>> >>> # Change this line if you want dns to get its upstream servers from >>> # somewhere other that /etc/resolv.conf >>> #resolv-file> >>> >>> >>> >>> # By default, dnsmasq will send queries to any of the upstream >>> # servers it knows about and tries to favour servers to are known >>> # to be up. Uncommenting this forces dnsmasq to try each query >>> # with each server strictly in the order they appear in >>> # /etc/resolv.conf >>> #strict-order >>> >>> >>> >>> >>> # If you don't want dnsmasq to read /etc/resolv.conf or any other >>> # file, getting its servers for this file instead (see below), then >>> # uncomment this >>> no-resolv >>> >>> # If you don't want dnsmasq to poll /etc/resolv.conf or other resolv >>> # files for changes and re-read them then uncomment this. >>> #no-poll >>> >>> >>> >>> >>> # Add other name servers here, with domain specs if they are for >>> # non-public domains. >>> server=158.152.1.58 server=158.152.1.43 > #server=/localnet/192.168.27.3 > >>> >>> >>> # Add local-only domains here, queries in these domains are answered >>> # from /etc/hosts or DHCP only. >>> #local=/localnet/ >>> >>> >>> >>> >>> # Add domains which you want to force to an IP address here. >>> # The example below send any host in doubleclick.net to a local >>> # webserver. >>> #address=/doubleclick.net/127.0.0.1 >>> >>> >>> >>> >>> # If you want dnsmasq to change uid and gid to something other >>> # than the default, edit the following lines. >>> #user> #group> >>> >>> >>> >>> # If you want dnsmasq to listen for DHCP and DNS requests only on >>> # specified interfaces (and the loopback) give the name of the >>> # interface (eg eth0) here. >>> # Repeat the line for more than one interface. >>> interface=eth2 # Or you can specify which interface _not_ to listen > on >>> #except-interface> # Or which to listen on by address (remember to >>> include 127.0.0.1 if # you use this.) #listen-address> # If you want >>> dnsmasq to provide only DNS service on > an >>> interface, # configure it as shown above, and then use the following >>> line to # disable DHCP on it. no-dhcp-interface=eth2 >>> >>> # On systems which support it, dnsmasq binds the wildcard address, >>> # even when it is listening on only some interfaces. It then discards >>> # requests that it shouldn't reply to. This has the advantage of >>> # working even when interfaces come and go and change address. If you >>> # want dnsmasq to really bind only the interfaces it is listening on, >>> # uncomment this option. About the only time you may need this is >>> > when >>> # running another nameserver on the same machine. >>> #bind-interfaces >>> >>> >>> >>> >>> # If you don't want dnsmasq to read /etc/hosts, uncomment the >>> # following line. >>> #no-hosts >>> # or if you want it to read another file, as well as /etc/hosts, use >>> # this. >>> #addn-hosts=/etc/banner_add_hosts >>> >>> >>> >>> >>> # Set this (and domain: see below) if you want to have a domain >>> # automatically added to simple names in a hosts-file. >>> #expand-hosts >>> >>> >>> >>> >>> # Set the domain for dnsmasq. this is optional, but if it is set, it >>> # does the following things. >>> # 1) Allows DHCP hosts to have fully qualified domain names, as long >>> # as the domain part matches this setting. >>> # 2) Sets the "domain" DHCP option thereby potentially setting the >>> # domain of all systems configured by DHCP >>> # 3) Provides the domain part for "expand-hosts" >>> domain=private.network >>> >>> # Uncomment this to enable the integrated DHCP server, you need >>> # to supply the range of addresses available for lease and optionally >>> # a lease time. If you have more than one network, you will need to >>> # repeat this for each network on which you want to supply DHCP >>> # service. >>> #dhcp-range=192.168.1.1,192.168.1.199,12h >>> >>> >>> >>> >>> # This is an example of a DHCP range where the netmask is given. This >>> # is needed for networks we reach the dnsmasq DHCP server via a >>> relay # agent. If you don't know what a DHCP relay agent is, you >>> probably # don't need to worry about this. >>> #dhcp-range=192.168.0.50,192.168.0.150,255.255.255.0,12h >>> >>> >>> >>> >>> # This is an example of a DHCP range with a network-id, so that >>> # some DHCP options may be set only for this network. >>> #dhcp-range=red,192.168.0.50,192.168.0.150 >>> >>> >>> >>> >>> # Supply parameters for specified hosts using DHCP. There are lots >>> # of valid alternatives, so we will give examples of each. Note that >>> # IP addresses DO NOT have to be in the range given above, they just >>> # need to be on the same network. The order of the parameters in >>> > these >>> # do not matter, it's permissble to give name,adddress and MAC in any >>> order >>> >>> # Always allocate the host with ethernet address 11:22:33:44:55:66 >>> # The IP address 192.168.0.60 >>> #dhcp-host=11:22:33:44:55:66,192.168.0.60 >>> >>> >>> >>> >>> # Always set the name of the host with hardware address >>> # 11:22:33:44:55:66 to be "fred" >>> #dhcp-host=11:22:33:44:55:66,fred >>> >>> >>> >>> >>> # Always give the host with ethernet address 11:22:33:44:55:66 >>> # the name fred and IP address 192.168.0.60 and lease time 45 minutes >>> #dhcp-host=11:22:33:44:55:66,fred,192.168.0.60,45m >>> >>> >>> >>> >>> # Give the machine which says it's name is "bert" IP address >>> # 192.168.0.70 and an infinite lease >>> #dhcp-host=bert,192.168.0.70,infinite >>> >>> >>> >>> >>> # Always give the host with client identifier 01:02:02:04 >>> # the IP address 192.168.0.60 >>> #dhcp-host=id:01:02:02:04,192.168.0.60 >>> >>> >>> >>> >>> # Always give the host with client identifier "marjorie" >>> # the IP address 192.168.0.60 >>> #dhcp-host=id:marjorie,192.168.0.60 >>> >>> >>> >>> >>> # Enable the address given for "judge" in /etc/hosts >>> # to be given to a machine presenting the name "judge" when >>> # it asks for a DHCP lease. >>> #dhcp-host=judge >>> >>> >>> >>> >>> # Never offer DHCP service to a machine whose ethernet >>> # address is 11:22:33:44:55:66 >>> #dhcp-host=11:22:33:44:55:66,ignore >>> >>> >>> >>> >>> # Ignore any client-id presented by the machine with ethernet >>> # address 11:22:33:44:55:66. This is useful to prevent a machine >>> # being treated differently when running under different OS's or >>> # between PXE boot and OS boot. >>> #dhcp-host=11:22:33:44:55:66,id:* >>> >>> >>> >>> >>> # Send extra options which are tagged as "red" to >>> # the machine with ethernet address 11:22:33:44:55:66 >>> #dhcp-host=11:22:33:44:55:66,net:red >>> >>> >>> >>> >>> # Send extra options which are tagged as "red" to >>> # any machine with ethernet address starting 11:22:33: >>> #dhcp-host=11:22:33:*:*:*,net:red >>> >>> >>> >>> >>> # Send extra options which are tagged as "red" to any machine whose >>> # DHCP vendorclass string includes the substring "Linux" >>> #dhcp-vendorclass=red,Linux >>> >>> >>> >>> >>> # Send extra options which are tagged as "red" to any machine one >>> # of whose DHCP userclass strings includes the substring "accounts" >>> #dhcp-userclass=red,accounts >>> >>> >>> >>> >>> # If this line is uncommented, dnsmasq will read /etc/ethers and act >>> # on the ethernet-address/IP pairs found there just as if they had >>> # been given as --dhcp-host options. Useful if you keep >>> # MAC-address/host mappings there for other purposes. >>> #read-ethers >>> >>> >>> >>> >>> # Send options to hosts which ask for a DHCP lease. >>> # See RFC 2132 for details of available options. >>> # Note that all the common settings, such as netmask and >>> # broadcast address, DNS server and default route, are given >>> # sane defaults by dnsmasq. You very likely will not need any >>> # any dhcp-options. If you use Windows clients and Samba, there >>> # are some options which are recommended, they are detailed at the >>> # end of this section. >>> # For reference, the common options are: >>> # subnet mask - 1 >>> # default router - 3 >>> # DNS server - 6 >>> # broadcast address - 28 >>> >>> >>> >>> >>> # Set the NTP time server addresses to 192.168.0.4 and 10.10.0.5 >>> #dhcp-option=42,192.168.0.4,10.10.0.5 >>> >>> >>> >>> >>> # Set the NTP time server address to be the same machine as >>> # is running dnsmasq >>> #dhcp-option=42,0.0.0.0 >>> >>> >>> >>> >>> # Set the NIS domain name to "welly" >>> #dhcp-option=40,welly >>> >>> >>> >>> >>> # Set the default time-to-live to 50 >>> #dhcp-option=23,50 >>> >>> >>> >>> >>> # Set the "all subnets are local" flag >>> #dhcp-option=27,1 >>> >>> >>> >>> >>> # Send the etherboot magic flag and then etherboot options (a >>> > string). >>> #dhcp-option=128,e4:45:74:68:00:00 >>> #dhcp-option=129,NIC=eepro100 >>> >>> >>> >>> >>> # Specify an option which will only be sent to the "red" network >>> # (see dhcp-range for the declaration of the "red" network) >>> #dhcp-option=red,42,192.168.1.1 >>> >>> >>> >>> >>> # The following DHCP options set up dnsmasq in the same way as is >>> specified # for the ISC dhcpcd in # >>> >>> >> > http://www.samba.org/samba/ftp/docs/textdocs/DHCP-Server-Configuration.t > >> >>> xt # adapted for a typical dnsmasq installation where the host > running # >>> dnsmasq is also the host running samba. # you may want to uncomment > them >>> if you use Windows clients and Samba. #dhcp-option=19,0 # >>> option ip-forwarding off #dhcp-option=44,0.0.0.0 # set >>> netbios-over-TCP/IP nameserver(s) >> aka >>> WINS server(s) >>> #dhcp-option=45,0.0.0.0 # netbios datagram distribution server >>> #dhcp-option=46,8 # netbios node type >>> #dhcp-option=47 # empty netbios scope. >>> >>> >>> >>> >>> # Send RFC-3397 DNS domain search DHCP option. WARNING: Your DHCP >>> >>> >> client >>> # probably doesn't support this...... >>> #dhcp-option=119,eng.apple.com,marketing.apple.com >>> >>> >>> >>> >>> # Send encapsulated vendor-class specific options. The vendor-class >>> # is sent as DHCP option 60, and all the options marked with the >>> # vendor class are send encapsulated in DHCP option 43. The meaning >>> > of >>> # the options is defined by the vendor-class. This example sets the >>> # mtftp address to 0.0.0.0 for PXEClients >>> #dhcp-option=vendor:PXEClient,1,0.0.0.0 >>> >>> >>> >>> >>> # Set the boot filename and tftpd server name and address >>> # for BOOTP. You will only need this is you want to >>> # boot machines over the network. >>> #dhcp-boot=/var/ftpd/pxelinux.0,boothost,192.168.0.3 >>> >>> >>> >>> >>> # Set the limit on DHCP leases, the default is 150 >>> #dhcp-lease-max=150 >>> >>> >>> >>> >>> # The DHCP server needs somewhere on disk to keep its lease database. >>> # This defaults to a sane location, but if you want to change it, >>> use # the line below. >>> #dhcp-leasefile=/var/lib/misc/dnsmasq.leases >>> >>> >>> >>> >>> # Set the DHCP server to authoritative mode. In this mode it will >>> >>> >> barge >>> in # and take over the lease for any client which broadcasts on the >>> network, # whether it has a record of the lease or not. This avoids >> long >>> timeouts # when a machine wakes up on a new network. DO NOT enable >> this if >>> there's # the slighest chance that you might end up accidentally >>> configuring a DHCP # server for your campus/company accidentally. The >>> ISC server uses the >>> same # the same option, and this URL provides more information: # >>> http://www.isc.org/index.pl?/sw/dhcp/authoritative.php >>> #dhcp-authoritative >>> >>> >>> >>> >>> # Set the cachesize here. >>> #cache-size=150 >>> >>> >>> >>> >>> # If you want to disable negative caching, uncomment this. >>> #no-negcache >>> >>> >>> >>> >>> # Normally responses which come form /etc/hosts and the DHCP lease >>> # file have Time-To-Live set as zero, which conventionally means >>> # do not cache further. If you are happy to trade lower load on the >>> # server for potentially stale date, you can set a time-to-live (in >>> # seconds) here. >>> #local-ttl> >>> >>> >>> >>> # If you want dnsmasq to detect attempts by Verisign to send queries >>> # to unregistered .com and .net hosts to its sitefinder service and >>> # have dnsmasq instead return the correct NXDOMAIN response, >>> > uncomment >>> # this line. You can add similar lines to do the same for other >>> # registries which have implemented wildcard A records. >>> #bogus-nxdomain=64.94.110.11 >>> >>> >>> >>> >>> # If you want to fix up DNS results from upstream servers, use the >>> # alias option. This only works for IPv4. >>> # This alias makes a result of 1.2.3.4 appear as 5.6.7.8 >>> #alias=1.2.3.4,5.6.7.8 >>> # and this maps 1.2.3.x to 5.6.7.x >>> #alias=1.2.3.0,5.6.7.0,255.255.255.0 >>> >>> >>> >>> >>> >>> # Change these lines if you want dnsmasq to serve MX records. >>> >>> >>> >>> >>> # Return an MX record named "maildomain.com" with target >>> # servermachine.com and preference 50 >>> #mx-host=maildomain.com,servermachine.com,50 >>> >>> >>> >>> >>> # Set the default target for MX records created using the localmx >>> option. #mx-target=servermachine.com >>> >>> >>> # Return an MX record pointing to the mx-target for all local >>> # machines. >>> #localmx >>> >>> >>> >>> >>> # Return an MX record pointing to itself for all local machines. >>> #selfmx >>> >>> >>> >>> >>> # Change the following lines if you want dnsmasq to serve SRV >>> # records. These are useful if you want to serve ldap requests for >>> # Active Directory and other windows-originated DNS requests. >>> # See RFC 2782. >>> # You may add multiple srv-host lines. >>> # The fields are <name>,<target>,<port>,<priority>,<weight> >>> # If the domain part if missing from the name (so that is just has >>> > the >>> # service and protocol sections) then the domain given by the domain> >>> > # > >>> config option is used. (Note that expand-hosts does not need to be # > set >>> for this to work.) >>> >>> >>> # A SRV record sending LDAP for the example.com domain to >>> # ldapserver.example.com port 289 >>> #srv-host=_ldap._tcp.example.com,ldapserver.example.com,389 >>> >>> >>> >>> >>> # A SRV record sending LDAP for the example.com domain to >>> # ldapserver.example.com port 289 (using domain=) >>> #domain=example.com >>> #srv-host=_ldap._tcp,ldapserver.example.com,389 >>> >>> >>> >>> >>> # Two SRV records for LDAP, each with different priorities >>> #srv-host=_ldap._tcp.example.com,ldapserver.example.com,389,1 >>> #srv-host=_ldap._tcp.example.com,ldapserver.example.com,389,2 >>> >>> >>> >>> >>> # A SRV record indicating that there is no LDAP server for the domain >>> # example.com >>> #srv-host=_ldap._tcp.example.com >>> >>> >>> >>> >>> >>> # Change the following lines to enable dnsmasq to serve TXT records. >>> # These are used for things like SPF and zeroconf. (Note that the >>> # domain-name expansion done for SRV records _does_not >>> # occur for TXT records.) >>> >>> >>> >>> >>> #Example SPF. >>> #txt-record=example.com,v=spf1 a -all >>> >>> >>> >>> >>> #Example zeroconf >>> #txt-record=_http._tcp.example.com,name=value,paper=A4 >>> >>> >>> >>> >>> >>> # For debugging purposes, log each DNS query as it passes through >>> # dnsmasq. >>> #log-queries >>> >>> >>> >>> >>> # Include a another lot of configuration options. >>> #conf-file=/etc/dnsmasq.more.conf >>> >>> >>> >>> >>> The information in this email is confidential and may be legally >>> privileged. It is intended solely for the addressee. Access to this >>> email by anyone else is unauthorised. >>> >>> If you are not the intended recipient, any disclosure, copying, >>> distribution or any action taken or omitted to be taken in reliance > on >> it >>> is prohibited and may be unlawful. >>> >>> The contents of an attachment to this email may contain software >>> >>> >> viruses >>> that could damage your own computer systems. Whilst The Spur Group > of >>> Companies has taken every precaution to minimise the risk, we cannot >>> accept liability for any damage that you sustain as a result of >> software >>> viruses. >>> >>> >>> >>> >> > ------------------------------------------------------------------------ > >> - >> >> >>> Using Tomcat but need to do more? Need to support web services, >>> security? Get stuff done quickly with pre-integrated technology to >> make >>> your job easier Download IBM WebSphere Application Server v.1.0.1 >> based on >>> Apache Geronimo >>> >>> >>> >> > http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642 > >> >>> >> > ------------------------------------------------------------------------ > >> >>> leaf-user mailing list: [email protected] >>> https://lists.sourceforge.net/lists/listinfo/leaf-user >>> Support Request -- http://leaf-project.org/ >>> >>> >>> >>> >> >> >> >> The information in this email is confidential and may be legally >> privileged. It is intended solely for the addressee. Access to this >> email by anyone else is unauthorised. >> >> If you are not the intended recipient, any disclosure, copying, >> distribution or any action taken or omitted to be taken in reliance on > it >> is prohibited and may be unlawful. >> >> The contents of an attachment to this email may contain software >> > viruses >> that could damage your own computer systems. Whilst The Spur Group of >> Companies has taken every precaution to minimise the risk, we cannot >> accept liability for any damage that you sustain as a result of > software >> viruses. >> >> > > > > > ------------------------------------------------------------------------ > - > Using Tomcat but need to do more? Need to support web services, > security? Get stuff done quickly with pre-integrated technology to make > your job easier Download IBM WebSphere Application Server v.1.0.1 based on > Apache > Geronimo > http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642 > ------------------------------------------------------------------------ > leaf-user mailing list: [email protected] > https://lists.sourceforge.net/lists/listinfo/leaf-user > Support Request -- http://leaf-project.org/ > > > The information in this email is confidential and may be legally > privileged. It is intended solely for the addressee. Access to this > email by anyone else is unauthorised. > > If you are not the intended recipient, any disclosure, copying, > distribution or any action taken or omitted to be taken in reliance on it > is prohibited and may be unlawful. > > The contents of an attachment to this email may contain software viruses > that could damage your own computer systems. Whilst The Spur Group of > Companies has taken every precaution to minimise the risk, we cannot > accept liability for any damage that you sustain as a result of software > viruses. > > > > ------------------------------------------------------------------------- > Using Tomcat but need to do more? Need to support web services, > security? Get stuff done quickly with pre-integrated technology to make > your job easier Download IBM WebSphere Application Server v.1.0.1 based on > Apache Geronimo > http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642 > ------------------------------------------------------------------------ > leaf-user mailing list: [email protected] > https://lists.sourceforge.net/lists/listinfo/leaf-user > Support Request -- http://leaf-project.org/ > > ------------------------------------------------------------------------- Using Tomcat but need to do more? Need to support web services, security? Get stuff done quickly with pre-integrated technology to make your job easier Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642 ------------------------------------------------------------------------ leaf-user mailing list: [email protected] https://lists.sourceforge.net/lists/listinfo/leaf-user Support Request -- http://leaf-project.org/
