Yup more excellent advice Mac. On Wed, Jun 21, 2023, 7:46 PM M.W.Foscue <[email protected]> wrote:
> I also recommend one goes to their local hardware store, buys a 7/16" (or > 1/2") rubber o-ring. Drop it in the collet hole. Then, when you insert > the bit, it rests on the o-ring and when you tighten the collet, the o-ring > compresses - keeping the bit from bottoming out. Been using that technique > for years in a couple of my routers. Works well. > > Mac > ------------------------------ > ------------------------------ > > -----Original Message----- > From: <[email protected]> > Sent: Jun 21, 2023 7:02 AM > To: <[email protected]> > Subject: Re: Router bit extension question > > > there you go. > > Kind Regards, > Timothy J. Ziegler > ------------------------------ > ------------------------------ > On Wed, Jun 21, 2023 at 12:18 AM <[email protected]> wrote: > >> Or just pop a bean bag bean on the router bit and slip the bit in till it >> touches >> >> And tighten it up >> >> >> >> Bill >> ------------------------------ >> ------------------------------ >> >> *From:* [email protected] < >> [email protected]> *On Behalf Of *M.W.Foscue >> *Sent:* Wednesday, June 21, 2023 2:24 PM >> *To:* [email protected] >> *Subject:* Re: Router bit extension question >> >> >> >> Tim, >> >> >> >> That's exactly what I do and teach. I insert the shank into router >> collet until it "bottoms out" (won't go in any further). I then lift it >> back up in the collet about 1/8 to 1/4 inch. Have never had one get stuck >> and never had one come loose either! There is/are one or two router bit >> manufacturers that do put a line /mark on the shank where they recommend >> you insert the shank into the collet to that mark. Mark looks something >> like: -->| >> >> >> >> Mac >> ------------------------------ >> ------------------------------ >> >> -----Original Message----- >> From: <[email protected]> >> Sent: Jun 20, 2023 10:49 PM >> To: <[email protected]> >> Subject: Re: Router bit extension question >> >> >> >> Great input Mike, >> >> Yes I have a rule of thumb to bottom it out then pull it out 1/16 inch, >> and tighten it up. Same with the Router extension. >> >> >> Kind Regards, >> >> Timothy J. Ziegler >> ------------------------------ >> ------------------------------ >> On Tue, Jun 20, 2023 at 9:40 PM Okla Mike (Liltwisted) < >> [email protected]> wrote: >> >> One of the things we have a tendency to do is push the shaft too far into >> the collet. Then when we tighten it, it will bury out and tighten up as a >> jamming to the bottom instead of squeeze onto the bit or extender shaft. >> So in this condition, without enough compression on the shaft, it will only >> take a little vibration to get everything loose enough to start slipping. >> Good thing for us, there is usually a lot of vibration noise or our work >> that gets in the way of launching it at us. The solution is; figure out >> how far you can insert the shaft and get a measurement. Then remove the >> collet and see how far in the shaft will run into the collet before it pops >> out the other end. Now if you add 1/8" to the collet measurement and >> subtract 1/4" from the depth measurement, you will have your safe install >> zone. On my carriage, I made those 2 marks, scratched into the metal. >> It's pretty easy to make an ink mark on the router bit to make sure you are >> in the safe area. Now install it and while running, you may lose the marks >> but you will never lose the bit! >> >> Now there is one more thing you need to do. Your extreme shaft may have >> suffered some damage. Make sure the shaft is smooth and free of burrs. If >> you need to polish it, you can chuck in a 1/2" shaft into the drill press >> and the chuck the extreme onto the shaft as well. you will now be able to >> spin the shaft and work out any imperfections the slip may have caused. >> Good luck and be safe. >> >> Mike OK >> ------------------------------ >> ------------------------------ >> >> >> >> On 6/20/2023 8:10 PM, Mike Newman wrote: >> >> I have a question for those of you that have the extreme router bit >> extension on their LOM router. How often do you check and re-tighten the >> extension into the router? I have had it come loose a couple of times with >> no real advance notice. Do you check it every time you use the router or >> so much run time between checks? Ruin the walking stick I was working on >> but no issues with the router or collett/nut that I can see/feel. >> >> -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/675419a9-9bc1-dbf6-dcdd-3a51d0297843%40earthlink.net > <https://groups.google.com/d/msgid/legacy-ornamental-mills/675419a9-9bc1-dbf6-dcdd-3a51d0297843%40earthlink.net?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLGC2YjN5D%3DE27PFPhEngnHQJdUzQy0xgxfuvvqLEMdPVw%40mail.gmail.com.
