Hi Leah and Persmule, I think the Wifi was my fault: I forgot to change the MAC-address of the image with ich9gen. I've made a new image with correct mac-address and now the wifi works. The strange thing with the wrong MAC-address was that I could see my wifi-networks but not connect to them. Ethernet-connection didn't work neither. But anyway: now with the correct mac both (ethernet and wifi) work. Another thing that changed with the new image: I get full resolution graphic screen (1440x900) from the beginning. Suspend doesn't work (as someone else reported) but I'll try a newer kernel version. I have two more questions: 1) since grub doesn't show up - how can I boot from usb / cd? 2) is Intel AMT / ME disabled (when i run cbmem -c it says "AMT enabled"?!) Thx and greetings, Marcel
On Wed, 10 Aug 2016 19:39:06 +0100 Leah Rowe <[email protected]> wrote: > -----BEGIN PGP SIGNED MESSAGE----- > Hash: SHA1 > > I'm not sure why that would happen. Thank you for your report, we'll > look into it. > > Op 10/08/16 om 14:26 schreef persmule: > > Hi Marcel and Leah, > > > > I built an image for T400_8mb from git revision 9eef871 (the > > newest), and flashed to my t400s. The result is nearly the same as > > Marcel's: My wifi doesn't work any more, with the switch turned > > ON! > > > > #rfkill list > >> 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: phy1: > >> Wireless LAN Soft blocked: no Hard blocked: yes > > (I installed 2 wlan cards on it.) > > > > And no matter how I flip the switch, the output rfkill generates > > remains the same. > > > > I have to flash a backup image built around Jun 30, then the > > wireless devices work fine. > > > > The outputs of dmesg and rfkill (generated under the newest image > > and the older backup one, accordingly) are attached. > > > > 在 2016年08月10日 15:22, Leah Rowe 写道: > >> Hi Marcel, > >> > >> Op 10/08/16 om 00:30 schreef Marcel Maci: > >> > >>> Hi Leah I flashed version experimental-96-g196d903 on my T400 > >>> and the results are very positive. I get: - no grub but > >>> graphical screen which is smaller than the display, no mouse - > >>> since I have encrypted disk I have then to switch to the text > >>> console to enter the passphrase - after that the system > >>> continues booting and I get full resolution login screen of > >>> Trisquel - I can switch between lcd and external monitor and > >>> adjust the brightness - everything works (which is great)! > >> > >> Thanks. > >> > >> This is expected behaviour on some T400 screens, where GRUB is > >> garbled or doesn't have a display at all, but GNU/Linux works > >> just fine. You can use an EHCI debug dongle for text mode serial > >> console in GRUB if you have that. This issue will probably be > >> fixed after the release, since it's only considered a minor > >> annoyance and not a blocker for release. > >> > >>> Strangely, I noticed that my wifi doesn't work any more - but > >>> maybe that's another problem and has nothing to do with the new > >>> version (?!) I send you the cbmem -c file as an attachment. Thx > >>> a lot - that's really good news for me! > >> > >> I don't think this has anything to do with libreboot, since we > >> hardcode-enable it. I checked and the patch should still have > >> been applied when building this snapshot. On the front of the > >> laptop on the left side, near the touchpad, there is a small > >> on/off switch for the wifi which might have been set to off > >> accidentally. Otherwise, "sudo rfkill list" can help you > >> determine what the problem is. > >> > >> > > > > > > - -- > Leah Rowe > > Libreboot developer > > Use free software. Free as in freedom. > https://www.gnu.org/philosophy/free-sw.html > > Use a free operating system, GNU/Linux. > https://www.gnu.org/ > > Use a free BIOS. > https://libreboot.org/ > > Support freedom. Join the Free Software Foundation. > https://fsf.org/ > > Minifree Ltd, trading as Ministry of Freedom | Registered in England, > No. 9361826 | VAT No. GB202190462 > Registered Office: 19 Hilton Road, Canvey Island, Essex SS8 9QA, UK | > Web: http://minifree.org/ > > -----BEGIN PGP SIGNATURE----- > Version: GnuPG v2.0.22 (GNU/Linux) > > iQEcBAEBAgAGBQJXq3TKAAoJEP9Ft0z50c+U6GUIALXRTFU5AL9s3//o5oFjPz1Y > oVBsaxaVil5k3eOoZDDqCmo3hOoX3iWfyIfqTNsnn3f4+AhuHItQScC+cZRNh7We > cc5pJ8eOE2qHkNtvGdB//n+08nPTS2ZLpmwHQ6ZXcLqEj0mRE0HywLofFLT9Mla/ > UCdSmNmIFQyECWkhKwEf8pgACYApowpuBSkTtcPLFtWo+TMLICoyAWfl06rvASFP > 99Mb13EJet3rRAQ/10haTrF+nlNx5VsoAY5paqC05S5GczjJipOvYWkm01DgM9jp > T4M/IboHrL1VzWPfw55KJYDOAjE09fUhtpeMrCvqMkRdpPQivaOsH6f1qLGwR8Q= > =dZ03 > -----END PGP SIGNATURE----- > -- Marcel Maci Avenue du Guintzet 15 1700 Fribourg 079 772 50 30 [email protected] www.liederlobby.ch
