-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 the descriptor doesn't affect wifi, only ethernet. It doesn't matter what MAC address you put there because it won't affect wifi
Op 10/08/16 om 23:16 schreef Marcel Maci: > Hi Leah and Persmule, I think the Wifi was my fault: I forgot to > change the MAC-address of the image with ich9gen. I've made a new > image with correct mac-address and now the wifi works. The strange > thing with the wrong MAC-address was that I could see my > wifi-networks but not connect to them. Ethernet-connection didn't > work neither. But anyway: now with the correct mac both (ethernet > and wifi) work. Another thing that changed with the new image: I > get full resolution graphic screen (1440x900) from the beginning. > Suspend doesn't work (as someone else reported) but I'll try a > newer kernel version. I have two more questions: 1) since grub > doesn't show up - how can I boot from usb / cd? 2) is Intel AMT / > ME disabled (when i run cbmem -c it says "AMT enabled"?!) Thx and > greetings, Marcel > > > On Wed, 10 Aug 2016 19:39:06 +0100 Leah Rowe <[email protected]> > wrote: > > I'm not sure why that would happen. Thank you for your report, > we'll look into it. > > Op 10/08/16 om 14:26 schreef persmule: >>>> Hi Marcel and Leah, >>>> >>>> I built an image for T400_8mb from git revision 9eef871 (the >>>> newest), and flashed to my t400s. The result is nearly the >>>> same as Marcel's: My wifi doesn't work any more, with the >>>> switch turned ON! >>>> >>>> #rfkill list >>>>> 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: >>>>> phy1: Wireless LAN Soft blocked: no Hard blocked: yes >>>> (I installed 2 wlan cards on it.) >>>> >>>> And no matter how I flip the switch, the output rfkill >>>> generates remains the same. >>>> >>>> I have to flash a backup image built around Jun 30, then the >>>> wireless devices work fine. >>>> >>>> The outputs of dmesg and rfkill (generated under the newest >>>> image and the older backup one, accordingly) are attached. >>>> >>>> 在 2016年08月10日 15:22, Leah Rowe 写道: >>>>> Hi Marcel, >>>>> >>>>> Op 10/08/16 om 00:30 schreef Marcel Maci: >>>>> >>>>>> Hi Leah I flashed version experimental-96-g196d903 on my >>>>>> T400 and the results are very positive. I get: - no grub >>>>>> but graphical screen which is smaller than the display, >>>>>> no mouse - since I have encrypted disk I have then to >>>>>> switch to the text console to enter the passphrase - >>>>>> after that the system continues booting and I get full >>>>>> resolution login screen of Trisquel - I can switch >>>>>> between lcd and external monitor and adjust the >>>>>> brightness - everything works (which is great)! >>>>> >>>>> Thanks. >>>>> >>>>> This is expected behaviour on some T400 screens, where GRUB >>>>> is garbled or doesn't have a display at all, but GNU/Linux >>>>> works just fine. You can use an EHCI debug dongle for text >>>>> mode serial console in GRUB if you have that. This issue >>>>> will probably be fixed after the release, since it's only >>>>> considered a minor annoyance and not a blocker for >>>>> release. >>>>> >>>>>> Strangely, I noticed that my wifi doesn't work any more - >>>>>> but maybe that's another problem and has nothing to do >>>>>> with the new version (?!) I send you the cbmem -c file as >>>>>> an attachment. Thx a lot - that's really good news for >>>>>> me! >>>>> >>>>> I don't think this has anything to do with libreboot, since >>>>> we hardcode-enable it. I checked and the patch should still >>>>> have been applied when building this snapshot. On the front >>>>> of the laptop on the left side, near the touchpad, there is >>>>> a small on/off switch for the wifi which might have been >>>>> set to off accidentally. Otherwise, "sudo rfkill list" can >>>>> help you determine what the problem is. >>>>> >>>>> >>>> >>>> > >> > > - -- Leah Rowe Libreboot developer Use free software. Free as in freedom. https://www.gnu.org/philosophy/free-sw.html Use a free operating system, GNU/Linux. https://www.gnu.org/ Use a free BIOS. https://libreboot.org/ Support freedom. Join the Free Software Foundation. https://fsf.org/ Minifree Ltd, trading as Ministry of Freedom | Registered in England, No. 9361826 | VAT No. GB202190462 Registered Office: 19 Hilton Road, Canvey Island, Essex SS8 9QA, UK | Web: http://minifree.org/ -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.22 (GNU/Linux) iQEcBAEBAgAGBQJXrFNqAAoJEP9Ft0z50c+UQLAH/2HdBrKUku+nYyBbPFmqlcUf tFHgJdGW1UqhtufksYorQc2MpR+Dn2z6/PYqr47SOS77Y17ouaq4jy7eGibvUT1W SK1PoS7mh0fGKv0YRh6/SRvJ/Pyk8yqtuvnNZUxtPVXgXB/QxXZODJPXAK02gFn6 G3/ktzsZwUk0RcenMIyOI3Fvvwc1Jyxw3lqQbfD+xJOT7IrS0cSpY/WzSR2Gj9cD HtiI8a5MFHWU2It4UeIyK+g8euL54PoayBcxKMhu7Tnbpxr+1Qs94KG7+ElZ5Uqf H3i4HOSfBc2EpOEWjaofrgV185D1OYCNOE+0MoeKsbKP2DnyZcuQRPu+LRJSIpQ= =NuhS -----END PGP SIGNATURE-----
