Date: Sun, 26 May 2002 10:26:42 -0500
From: John Musielewicz <[EMAIL PROTECTED]>
Subject: Re: [LIB] Panasonic li-ion

CGR 17670. 3 of them. 17 by 54 mm

On Sun, 26 May 2002 06:35:17 -0700, you wrote:

>Date: Sun, 26 May 2002 09:27:46 -0400
>From: "Gennadiy Tsygan" <[EMAIL PROTECTED]>
>Subject: Re: [LIB] Panasonic li-ion
>
>John, which cells were originally used in the PA2452 battery? Panasonic CGR
>17670? I am thinking of buying the battery and using the cells to fix a 2503
>battery for 110. I tried to put 1800 mAh Panasonic cells in it, but they
>wouldn't fit.
>
>----- Original Message -----
>From: "John Musielewicz" <[EMAIL PROTECTED]>
>To: "Libretto" <[EMAIL PROTECTED]>
>Sent: Saturday, May 18, 2002 3:45 AM
>Subject: [LIB] Panasonic li-ion
>
>
>> Date: Sat, 18 May 2002 02:27:44 -0500
>> From: "John Musielewicz" <[EMAIL PROTECTED]>
>> Subject: Panasonic li-ion
>>
>> If anyone's interested here's the Panasonic site which has their li-ion
>> cells and technical info.
>>
>>
>> http://www.panasonic.com/industrial/battery/oem/chem/lithion/index.html
>>
>> They have a 1800 mAh cell but it is the same size as a 2000 mAh LG Chem. I
>> think with any 18mm cell there is going to be some modifications of  the
>> case that will need to be done. Especially if the cells are stacked.
>That's
>> even saying the LG cells will survive with a panasonic charging system. I
>> think so though. I haven't seen a LG data sheet yet but every li-on cell I
>> have seen the data sheet for pretty much uses the same charging voltage
>and
>> current. Charge until it reaches 4.2 volts or the current drops to ..1-.07
>> CmA. On 1200 mAh is 120- 84 mA on 2000 mAh is 200-140 mA. About a 40
>percent
>> differance and the lower range on the 2000 almost intesects with the 1200.
>> Personally I think the voltage will reach 4.2 before the battery becomes
>> seriously overcharged and overheats. It may not hurt to examine the board
>> though and see how they measure current. All it may take is a resistor
>> change to exactly match the capacity of the battery to the ammeter. I
>doubt
>> the controller has both an ammeter and voltmeter built in. Probably just a
>> voltmeter and it uses the voltage drop across a shunt resistor to measure
>> current.
>>
>> John
>>
>>
>>
>>
>> **************************************************************
>> http://libretto.basiclink.com - Libretto mailing list
>> http://www.silverace.com/libretto/ - Archives
>>
>>                  -------TO UNSUBSCRIBE-------
>> Reply to any of the list messages. The reply mail should be
>> addressed to: [EMAIL PROTECTED] - Then replace any text
>> on the message's subject line: cmd:unsubscribe
>>               --------TO UNSUBSCRIBE DIGEST------
>> Do above but with this on subject line: cmd:unsubscribe digest
>> **************************************************************
>>
>>
>>
>
>
>
>
>**************************************************************
>http://libretto.basiclink.com - Libretto mailing list
>http://www.silverace.com/libretto/ - Archives
>
>                 -------TO UNSUBSCRIBE-------
>Reply to any of the list messages. The reply mail should be
>addressed to: [EMAIL PROTECTED] - Then replace any text
>on the message's subject line: cmd:unsubscribe
>              --------TO UNSUBSCRIBE DIGEST------
>Do above but with this on subject line: cmd:unsubscribe digest
>**************************************************************
>




**************************************************************
http://libretto.basiclink.com - Libretto mailing list
http://www.silverace.com/libretto/ - Archives

                 -------TO UNSUBSCRIBE-------
Reply to any of the list messages. The reply mail should be
addressed to: [EMAIL PROTECTED] - Then replace any text
on the message's subject line: cmd:unsubscribe
              --------TO UNSUBSCRIBE DIGEST------
Do above but with this on subject line: cmd:unsubscribe digest
**************************************************************


Reply via email to