Hi, Mark.
I think that your problem is that you've only defined 1 CTC....you need two
to get Linux to connect to
the VM TCPIP stack. Try this:
1) from the CMS Ready prompt in the Linux virtual machine:
a) DEFINE CTC 600
b) DEFINE CTC 601
c) COUPLE 600 TCPIP xxx
d) COUPLE 601 TCPIP yyy
2) boot Linux and make sure the ctc parm looks like this:
ctc=0x0600,0x0601
Good luck.
Dave Jones
> -----Original Message-----
> From: Linux on 390 Port [mailto:[EMAIL PROTECTED]]On Behalf Of
> Dorney, Mark
> Sent: Wednesday, April 17, 2002 1:26 PM
> To: [EMAIL PROTECTED]
> Subject: CTC's Turbolinux 6.5
>
>
> First off, serious newbie alert, mainframer thrown into this world for a
> POC.
>
> I'm doing an install from tape, I get to the part where I specify my CTC
> information and I start getting errors (logs are at the end). I believe
> that the hardware is ok since I went through the archives and although I
> couldn't find my specific situation I ran through some other
> suggestions of
> shutting down the network, rmmod ctc, insmod ctc and restarting
> the network.
> I tried to manually configure the network by doing an "ifconfig
> ctc0......"
> and at one point in the day I was able to ping successfully. All
> efforts to
> duplicate that success have failed.
>
> Here's what I'm getting:
> --------------------------------------------------------------------------
>
> Please review your selection:
>
> --------------------------------------------------------------------------
>
>
>
> Hostname : mylinux.state.wi.us
>
>
>
> Gateway IP : 198.150.235.17
>
> Gateway Device : ctc0
>
>
>
> Nameserver IP : 198.150.235.21
>
> Searchlist : state.wi.us
>
> CTC options : ctc=0x600
>
>
>
> --------------------------------------------------------------------------
>
> Do you want to use these settings? (y/n)y
>
> y
>
> CTC driver Version: 1.29 initialized
>
> channel: 0 Parallel channel found - 2 ESCON channel found
>
> escon0: read dev: 0600 irq: 000c - write dev: 0601 irq: 000d
>
> SIOCSIFADDR: No such device
>
> ctc0: unknown interface: No such device
>
> SIOCSIFDSTADDR: No such device
>
> ctc0: unknown interface: No such device
>
> SIOCSIFMTU: No such device
>
> SIOCADDRT: No such device
>
> ctc0: error fetching interface information: Device not found
>
> search state.wi.us
>
> Starting portmapper: portmap
>
> Mounting remote filesystems.
>
> Starting system logger: syslogd
>
> Stop network, rmmod ctc, etc reults in *****************
>
> bash-2.04# rmmod ctc
> rmmod ctc
> bash-2.04# cd /lib/modules/2.2.19/misc
> cd /lib/modules/2.2.19/misc
> bash-2.04# insmod ctc
> insmod ctc
> Using /lib/modules/2.2.19/misc/ctc.o
> bash-2.04# /etc/rc.d/init.d/network start
> /etc/rc.d/init.d/network start
> SIOCSIFADDR: No such device
> ctc0: unknown interface: No such device
> SIOCSIFDSTADDR: No such device
> ctc0: unknown interface: No such device
> SIOCSIFMTU: No such device
> SIOCADDRT: No such device
> ctc0: error fetching interface information: Device not found
> search state.wi.us
> bash-2.04#
>
> Thanks for any help anyone can provide
>
> Mark Dorney
>
