Just by looking at the two addresses for VHIP1 and VHIP2 you will have a
problem.
1 - the HOME/GATEWAY address for VHIP1 should be 10.21.25.10 /0.21.25.0
2 - I'm assuming that you have done the CP related commands for
GuestLAN support, and you are running SuSE 7.0
with the latest patches.
- /etc/chandev.conf and /etc/module.conf
|--------+--------------------------------->
| | "Ketchens, LeMarr T. |
| | (RyTull)" |
| | <LeMarr.Ketchens@ryerso|
| | ntull.com> |
| | Sent by: Linux on 390 |
| | Port |
| | <[EMAIL PROTECTED]|
| | U> |
| | |
| | |
| | 01/31/2003 07:33 PM |
| | Please respond to Linux|
| | on 390 Port |
| | |
|--------+--------------------------------->
>-----------------------------------------------------------------------------------------------------------|
|
|
| To: [EMAIL PROTECTED]
|
| cc:
|
| Subject: z/VM Guest LAN using HiperSockets
|
>-----------------------------------------------------------------------------------------------------------|
Okay, I've figured out how to run a Linux Guest as vctc and connect with no
problem. Right now, I need to know how to get this running with Guest LAN
using virtual Hipersockets. I think I can figure the issues on the Linux
Guest side, but I need to know what to use in the PROFILE TCPIP. I need to
know based on the following:
OSA-E 0090-0092 => z/VM TCPIP => 10.25.25.155
Virtual HIPER 2000-2002 => Portname:VIRTHIP1
Virtual HiperLan 2100-2102 => Portname:VIRTHIP2
Projected Linux Guest IP Addresses:
Linux01 => 10.22.25.10
Linux02 => 10.22.25.11
We do have a Cisco Router => 10.25.1.1
; OSA-E GIGABIT ETHERNET CARD ON Z/800 CHPID =>00
DEVICE DEV@0090 OSD 0090 PORTNAME VMHOST PRIROUTER
LINK ETH0 QDIOETHERNET DEV@0090
; VIRTUAL HIPERSOCKETS 2000-2002 VHIP1
DEVICE VHIP1 HIPERS 2000 PORTNAME VIRTHIP1 AUTORESTART
LINK VHIP1 QDIOIP VHIP1
; VIRTUAL HIPERSOCKETS 2100-2102 VHIP2 (Guest LAN)
DEVICE VHIP2 HIPERS 2100 PORTNAME VIRTHIP2 AUTORESTART
LINK VHIP2 QDIOIP VHIP2
HOME
10.25.25.155 ETH0
10.22.25.10 VHIP1
10.22.25.11 VHIP2
; (End HOME Address information)
; ------------------------------------------------------------------
GATEWAY
; ------------------------------------------------------------------
10 = ETH0 1500 0.255.0.0 0.25.0.0
10 = VHIP1 1500 0.255.255.0 0.22.25.0
10 = VHIP2 1500 0.255.255.0 0.22.25.0
DEFAULTNET 10.25.25.155 ETH0 1500 0
; (End GATEWAY Static Routing information)
START DEV@0090
START VHIP1
START VHIP2
; (End START statements)
With these as the statements, I want to know if I'm going down the wrong
path trying to utilize Guest LAN with virtual Hipersockets.
--- Legal Disclaimer: The information contained in this communication may
be
confidential, is intended only for the use of the recipient named above,
and
may be legally privileged. If the reader of this message is not the
intended recipient, you are hereby notified that any dissemination,
distribution, or copying of this communication, or any of its contents, is
strictly prohibited. If you have received this communication in error,
please re-send this communication to the sender and delete the original
message and any copy of it from your computer system. Thank you. ---
