Hello. I'm having a problem getting connected to a linux image.
Everything seems to go ok during the boot and subsequent config. "ok" as
in no error messages. I'm running a z800, z/VM 4.3.0, OSA-Express Gig.
addresses E100 -> E102. These addresses are attached the linux guest,
LNXRH01. When I issue and IFCONFIG on LNXRH01 all that shows is lo. I'd
expect to see eth0 (right?). When I try to do an ifconfig to define, it
says the device does not exist. When I issue it for sit0, it works as in
it accepts the ifconfig command. Ping'ing however from VM or my PC
results in a request time out. I've include the console listing below,
it's kind of lengthy but would appreciate a review of it and perhaps some
guidance/suggestions.
As always,
Thanks
Steve Gentry
Lafayette Life Ins. Co.
<console>
DMSACP723I D (592) R/O
DMSACR723I U (VMSYS:MAINT.ACC) R/O
Ready;
redhat
0000004 FILES PURGED
RDR FILE 0038 SENT FROM LNXRH01 PUN WAS 0038 RECS 033K CPY 001 A NOHOLD
NOKEEP
RDR FILE 0039 SENT FROM LNXRH01 PUN WAS 0039 RECS 0001 CPY 001 A NOHOLD
NOKEEP
RDR FILE 0040 SENT FROM LNXRH01 PUN WAS 0040 RECS 060K CPY 001 A NOHOLD
NOKEEP
0000003 FILES CHANGED
0000003 FILES CHANGED
hwc low level driver: can write messages
hwc low level driver: can not read state change notifications
hwc low level driver: can read commands
hwc low level driver: can read priority commands
Linux version 2.4.9-37BOOT ([EMAIL PROTECTED]) (gcc version 2.95.3
20010315 (release)) #1 SMP Wed Apr 24 17:32:38 CEST 2002
We are running under VM
This machine has an IEEE fpu
On node 0 totalpages: 32768
zone(0): 32768 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram0 ro ip=off DASD=200-20F
Highest subchannel number detected (hex) : 0012
Calibrating delay loop...
632.42 BogoMIPS
Memory: 119776k/131072k available (1626k kernel code, 0k reserved, 844k
data, 64k init)
Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 6, 262144 bytes)
debug: Initialization complete
debug: reserved 4 areas of 4 pages for debugging ccwcache
POSIX conformance testing by UNIFIX
Detected 1 CPU's
Boot cpu address 0
cpu 0 phys_idx=0 vers=FF ident=02107A machine=2066 unused=0000
init_mach : starting machine check handler
init_mach : machine check buffer : head = 0023EDF0
init_mach : machine check buffer : tail = 0023EDF4
init_mach : machine check buffer : free = 0023EDF8
init_mach : CRW entry buffer anchor = 0023EDFC
init_mach : machine check handler ready
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
mach_handler : ready
mach_handler : waiting for wakeup
Starting kswapd v1.8
VFS: Diskquotas version dquot_6.5.0 initialized
pty: 256 Unix98 ptys configured
block: queued sectors max/low 79397kB/26465kB, 256 slots per queue
RAMDISK driver initialized: 16 RAM disks of 35840K size 1024 blocksize
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
debug: reserved 4 areas of 16 pages for debugging cio_msg
debug: cio_msg: new level 2
debug: reserved 4 areas of 16 pages for debugging cio_trace
debug: cio_trace: new level 2
debug: reserved 4 areas of 4 pages for debugging cio_crw
debug: cio_crw: new level 6
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 8Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 4667k freed
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 16k freed
Starting the S/390 initrd to configure networking. Version is 0.51
Please enter the FQDN of your new virtual machine (e.g. s390.redhat.com):
lnxrh01.vm.llic.com
Please enter the network device you intend to use (e.g. ctc0, escon0,
iucv0, eth0, hsi0, tr0):
eth0
Please enter parameters you need to pass to the channel device layer.
This includes the I/O ports of your ctc, escon, qeth, hsi and lcs devices.
Additional parameters for QETH devices such as the portname
should be entered at the next prompt, not here !
(e.g. "ctc0,0x600,0x601" will activate the ctc0 interface at I/O
ports 0x600,0x601):
qeth0,0xe100,0xe101,0xe102
Each OSA-Express feature in QDIO mode must be associated with a port name
Please enter additional parameters for your QETH device
(e.g. "add_parms,0x10,{lo_devno,hi_devno},portname:port_name")
Press enter if you don't want to enter additional parameters
add_parms,0x10,0xe100,0xe102,portname:CHPID01
Please enter the IP address of your new virtual machine:
10.140.2.40
Please enter your netmask (e.g. 255.255.255.0):
255.255.255.0
Please enter your broadcast address:
10.140.2.255
Please enter your network address:
10.140.2.0
Please enter your default gateway:
10.140.2.254
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
Please enter your DNS server(s), separated by colons (:):
162.133.1.19:162.133.1.22
Please enter your DNS search domain(s) (if any), separated by colons (:):
llic.com
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use
Iface
127.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 lo
Starting portmap.
Loading DASD kernel module. This can take a while.
dasd:initializing...
debug: reserved 2 areas of 1 pages for debugging dasd
dasd:Registered successfully to major no 94
dasd:initialization finished
dasd(eckd):ECKD discipline initializing
dasd(eckd):0201 on sch 5: 3390/0A(CU:3990/01) Cyl:400 Head:15 Sec:224
dasd(eckd):0201 on sch 5: 3390/0A(CU:3990/01): Configuration data read
debug: reserved 2 areas of 1 pages for debugging dasdb
dasd(eckd):0203 on sch 7: 3390/0A(CU:3990/01) Cyl:1500 Head:15 Sec:224
dasd(eckd):0203 on sch 7: 3390/0A(CU:3990/01): Configuration data read
debug: reserved 2 areas of 1 pages for debugging dasdd
dasd(eckd):0204 on sch 8: 3390/0A(CU:3990/01) Cyl:500 Head:15 Sec:224
dasd(eckd):/dev/dasdb(94:4),[EMAIL PROTECTED]:(4kB blks): 288000kB at 48kB/trk
compatible disk layout
dasd(eckd):0204 on sch 8: 3390/0A(CU:3990/01): Configuration data read
debug: reserved 2 areas of 1 pages for debugging dasde
dasd(eckd):0205 on sch 9: 3390/0A(CU:3990/01) Cyl:800 Head:15 Sec:224
dasd(eckd):0205 on sch 9: 3390/0A(CU:3990/01): Configuration data read
debug: reserved 2 areas of 1 pages for debugging dasdf
dasd(eckd):0206 on sch 10: 3390/0A(CU:3990/01) Cyl:200 Head:15 Sec:224
dasd(eckd):0206 on sch 10: 3390/0A(CU:3990/01): Configuration data read
debug: reserved 2 areas of 1 pages for debugging dasdg
dasd(eckd):/dev/dasdd(94:12),[EMAIL PROTECTED]:(4kB blks): 1080000kB at 48kB/trk
compatible disk layout
dasd:waiting for responses...
dasd(eckd):/dev/dasde(94:16),[EMAIL PROTECTED]:(4kB blks): 360000kB at 48kB/trk
compatible disk layout
dasd(eckd):/dev/dasdg(94:24),[EMAIL PROTECTED]:(4kB blks): 144000kB at 48kB/trk
compatible disk layout
dasd(eckd):/dev/dasdf(94:20),[EMAIL PROTECTED]:(4kB blks): 576000kB at 48kB/trk
compatible disk layout
Partition check:
dasdb:VOL1/ 0X0201: dasdb dasdb1
dasdd:VOL1/ 0X0203: dasdd dasdd1
dasde:VOL1/ 0X0204: dasde dasde1
dasdf:VOL1/ 0X0205: dasdf dasdf1
dasdg:VOL1/ 0X0206: dasdg dasdg1
dasd(eckd):We are interested in: CU 3880/00
dasd(eckd):We are interested in: CU 3990/00
dasd(eckd):We are interested in: CU 2105/00
dasd(eckd):We are interested in: CU 9343/00
Journalled Block Device driver loaded
Starting telnetd and sshd to allow login over the network.
Please connect now to 10.140.2.40 and start 'loader' from this shell.
sh-2.05#
ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
sh-2.05#
ifconfig eth0 10.140.2.40 netmask 255.255.255.0 broadcast 10.140.2.255 mtu
1492 up
SIOCSIFADDR: No such device
eth0: unknown interface: No such device
SIOCSIFNETMASK: No such device
SIOCSIFBRDADDR: No such device
eth0: unknown interface: No such device
SIOCSIFMTU: No such device
eth0: unknown interface: No such device
sh-2.05#
ifconfig eth0 10.140.2.40
SIOCSIFADDR: No such device
eth0: unknown interface: No such device
sh-2.05#
ifconfig qeth0 10.140.2.40 netmask 255.255.255.0 broadcast 10.140.2.255
mtu 1492 up
SIOCSIFADDR: No such device
qeth0: unknown interface: No such device
SIOCSIFNETMASK: No such device
SIOCSIFBRDADDR: No such device
qeth0: unknown interface: No such device
SIOCSIFMTU: No such device
qeth0: unknown interface: No such device
sh-2.05#
SPOOL CONSOLE CLOSE
</console>
