Gianfranco pointed out one problem, but the more fundamental issue is that you have QDIO NICs defined, and not HiperSocket ones. "Q NIC" and "Q LAN" will verify that, but the messages in your log are pretty clear: qeth: Device 0x610/0x611/0x612 is a Guest LAN QDIO card (level: V511) with link qeth: Device 0x610/0x611/0x612 is a Guest LAN QDIO card (level: V511) with link type Gigabit Eth (portname: OSD03) qeth: Broadcast packets will not be echoed back on eth1. qeth: Trying to use card with devnos 0x600/0x601/0x602 qeth: Device 0x600/0x601/0x602 is a Guest LAN QDIO card (level: V511) with link type Gigabit Eth (portname: OSD00) qeth: Broadcast packets will not be echoed back on eth0. eth0: no IPv6 routers present eth1: no IPv6 routers present
Note the interface names: eth0 and eth1, not hsi0 and hsi1. Mark Post -----Original Message----- From: Linux on 390 Port [mailto:[EMAIL PROTECTED] On Behalf Of Peter E. Abresch Jr. - at Pepco Sent: Friday, January 07, 2005 10:46 AM To: [email protected] Subject: Linux Hipersockets under z/VM I am having problems with hipersocket. I have hipersockets working fine on 2 native Linux LPARs however, this is my first attempt under z/VM. linuxm01:/etc/sysconfig/network # ifconfig hsi0 hsi0: error fetching interface information: Device not found linuxm01:/etc/sysconfig/network # ifconfig hsi0 up hsi0: unknown interface: No such device No matter what, I cannot seem to get this to work. I will mention that my Linux guest are running 2.4.21-266 and on my native Linux LPARs I am running 2.4.21-251. I remember reading something that 2.4.21-266 was not working correctly but I thought it was just limited to virtual hipersockets off a vlan. Is my problem mine or is it 2.4.21-266? Some info follows: In /etc/modules.conf . . . alias eth0 qeth alias eth1 qeth alias hsi0 qeth In /etc/chandev/conf . . . noauto;qeth0,0x0600,0x0601,0x0602,0,0;add_parms,0x10,0x0600,0x0602,portname: OSD00 noauto;qeth1,0x0610,0x0611,0x0612,0,0;add_parms,0x10,0x0610,0x0612,portname: OSD03 noauto;qeth0,0x0620,0x0621,0x0622,0,0,0 In /etc/sysconfig/network/ifcfg-hsi0 BOOTPROTO='static' STARTMODE='onboot' IPADDR='161.186.86.150' MTU='16384' NETMASK='255.255.255.192' NETWORK='161.186.86.128' BROADCAST='161.186.86.191' A z/VM query reveals: OSA 0600 ON NIC 0600 UNIT 000 SUBCHANNEL = 0006 0600 QDIO-ELIGIBLE QIOASSIST NOT AVAILABLE OSA 0601 ON NIC 0600 UNIT 001 SUBCHANNEL = 0007 0601 QDIO-ELIGIBLE QIOASSIST NOT AVAILABLE OSA 0602 ON NIC 0600 UNIT 002 SUBCHANNEL = 0008 0602 QDIO ACTIVE QIOASSIST NOT AVAILABLE 0602 INP + 01 IOCNT = 00000192 ADP = 096 PROG = 000 UNAVAIL = 032 0602 BYTES = 000000000000640C 0602 OUT + 01 IOCNT = 00000000 ADP = 000 PROG = 000 UNAVAIL = 128 0602 BYTES = 0000000000000000 0602 OUT + 02 IOCNT = 00000000 ADP = 000 PROG = 000 UNAVAIL = 128 0602 BYTES = 0000000000000000 0602 OUT + 03 IOCNT = 00000260 ADP = 000 PROG = 128 UNAVAIL = 000 0602 BYTES = 00000000000071A6 0602 OUT + 04 IOCNT = 00000000 ADP = 000 PROG = 000 UNAVAIL = 128 0602 BYTES = 0000000000000000 OSA 0610 ON NIC 0610 UNIT 000 SUBCHANNEL = 0009 0610 QDIO-ELIGIBLE QIOASSIST NOT AVAILABLE OSA 0611 ON NIC 0610 UNIT 001 SUBCHANNEL = 000A 0611 QDIO-ELIGIBLE QIOASSIST NOT AVAILABLE OSA 0612 ON NIC 0610 UNIT 002 SUBCHANNEL = 000B 0612 QDIO ACTIVE QIOASSIST NOT AVAILABLE 0612 INP + 01 IOCNT = 00000000 ADP = 096 PROG = 000 UNAVAIL = 032 0612 BYTES = 0000000000000000 0612 OUT + 01 IOCNT = 00000000 ADP = 000 PROG = 000 UNAVAIL = 128 0612 BYTES = 0000000000000000 0612 OUT + 02 IOCNT = 00000000 ADP = 000 PROG = 000 UNAVAIL = 128 0612 BYTES = 0000000000000000 0612 OUT + 03 IOCNT = 00000004 ADP = 000 PROG = 004 UNAVAIL = 124 0612 BYTES = 00000000000001A0 0612 OUT + 04 IOCNT = 00000000 ADP = 000 PROG = 000 UNAVAIL = 128 0612 BYTES = 0000000000000000 OSA 0620 ON OSA FE04 SUBCHANNEL = 0014 0620 QDIO-ELIGIBLE QIOASSIST NOT AVAILABLE OSA 0621 ON OSA FE05 SUBCHANNEL = 0015 0621 QDIO-ELIGIBLE QIOASSIST NOT AVAILABLE OSA 0622 ON OSA FE06 SUBCHANNEL = 0016 0622 QDIO-ELIGIBLE QIOASSIST NOT AVAILABLE During bootup I see: qeth: Trying to use card with devnos 0x620/0x621/0x622 qdio : response upon setting indicators is 0x3. qeth: sense data available on read channel. qeth: irb: 01 c2 40 17 01 23 6f 50 0e 00 10 10 00 80 00 00 qeth: irb: 01 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 qeth: sense data: 00 00 af fe 00 00 00 00 00 00 00 00 00 00 00 00 qeth: sense data: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 qeth: unit check/exception in read_handler (irq 0x14, devstat 0x0e, schstat 0x00, rqparam 0x1005) qdio : response upon setting indicators is 0x3. qdio : response upon setting indicators is 0x3. qeth: sense data available on read channel. qeth: irb: 01 c2 40 17 01 23 6f 50 0e 00 10 10 00 80 00 00 qeth: irb: 01 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 qeth: sense data: 00 00 af fe 00 00 00 00 00 00 00 00 00 00 00 00 qeth: sense data: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 qeth: unit check/exception in read_handler (irq 0x14, devstat 0x0e, schstat 0x00, rqparam 0x1005) qdio : response upon setting indicators is 0x3. qdio : response upon setting indicators is 0x3. qeth: sense data available on read channel. qeth: irb: 01 c2 40 17 01 23 6f 50 0e 00 10 10 00 80 00 00 qeth: irb: 01 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 qeth: sense data: 00 00 af fe 00 00 00 00 00 00 00 00 00 00 00 00 qeth: sense data: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 qeth: unit check/exception in read_handler (irq 0x14, devstat 0x0e, schstat 0x00, rqparam 0x1005) qdio : response upon setting indicators is 0x3. qdio : response upon setting indicators is 0x3. qeth: sense data available on read channel. qeth: irb: 01 c2 40 17 01 23 6f 50 0e 00 10 10 00 80 00 00 qeth: irb: 01 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 qeth: sense data: 00 00 af fe 00 00 00 00 00 00 00 00 00 00 00 00 qeth: sense data: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 qeth: unit check/exception in read_handler (irq 0x14, devstat 0x0e, schstat 0x00, rqparam 0x1005) qdio : response upon setting indicators is 0x3. qdio : response upon setting indicators is 0x3. qeth: sense data available on read channel. qeth: irb: 01 c2 40 17 01 23 6f 50 0e 00 10 10 00 80 00 00 qeth: irb: 01 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 qeth: sense data: 00 00 af fe 00 00 00 00 00 00 00 00 00 00 00 00 qeth: sense data: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 qeth: unit check/exception in read_handler (irq 0x14, devstat 0x0e, schstat 0x00, rqparam 0x1005) qdio : response upon setting indicators is 0x3. qdio : response upon setting indicators is 0x3. qeth: sense data available on read channel. qeth: irb: 01 c2 40 17 01 23 6f 50 0e 00 10 10 00 80 00 00 qeth: irb: 01 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 qeth: sense data: 00 00 af fe 00 00 00 00 00 00 00 00 00 00 00 00 qeth: sense data: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 qeth: unit check/exception in read_handler (irq 0x14, devstat 0x0e, schstat 0x00, rqparam 0x1005) qdio : response upon setting indicators is 0x3. qeth: recovery not successful on device 0x620/0x621/0x622; giving up. qeth: There were problems in hard-setting up the card. qeth: Trying to use card with devnos 0x610/0x611/0x612 qeth: Device 0x610/0x611/0x612 is a Guest LAN QDIO card (level: V511) with link type Gigabit Eth (portname: OSD03) qeth: Broadcast packets will not be echoed back on eth1. qeth: Trying to use card with devnos 0x600/0x601/0x602 qeth: Device 0x600/0x601/0x602 is a Guest LAN QDIO card (level: V511) with link type Gigabit Eth (portname: OSD00) qeth: Broadcast packets will not be echoed back on eth0. eth0: no IPv6 routers present eth1: no IPv6 routers present ---------------------------------------------------------------------- For LINUX-390 subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: INFO LINUX-390 or visit http://www.marist.edu/htbin/wlvindex?LINUX-390 ---------------------------------------------------------------------- For LINUX-390 subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: INFO LINUX-390 or visit http://www.marist.edu/htbin/wlvindex?LINUX-390
