Hello all,
I am trying to set up a vipa for sles9 linux running under VM 5.2. Each
linux runs eth0,1 through a virtual switch connected to two chpids.
I have gone through previous emails on this subject, but still seem to be
at a loss. Everything I have setup appears to be correct, and
when I start ospfd the vipa broadcasts so that the neighbors are aware of
it, but yet I cannot ping it. I see the following messages in the
quagga.log:
2006/08/10 14:53:53 OSPF: Link State Update: Neighbor[10.115.128.3] state
is less than Exchange
2006/08/10 14:53:53 OSPF: Link State Update: Neighbor[10.115.128.2] state
is less than Exchange
2006/08/10 14:53:55 OSPF: Packet[DD]: MTU is larger than
[eth1:10.115.137.51]'s MTU
2006/08/10 14:53:56 OSPF: Packet[DD]: MTU is larger than
[eth0:10.115.136.51]'s MTU
we have the mtu set at 1400 for linux dummy0 and eth0,1
Currently we have MTU set at 1400 on working vipas on both VM and MVS
systems.
When I do an ifconfig, I can see the outgoing packets but none are
received.
Here is the ifconfig output:
linux-00:/var/log/quagga # ifconfig
dummy0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
inet addr:10.115.20.185 Bcast:10.115.20.191
Mask:255.255.255.248
inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link
UP BROADCAST RUNNING NOARP MTU:1400 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:90 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:6972 (6.8 Kb)
eth0 Link encap:Ethernet HWaddr 02:00:00:00:00:01
inet addr:10.115.136.51 Bcast:10.115.136.255 Mask:255.255.255.0
inet6 addr: fe80::200:0:a00:1/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1400 Metric:1
RX packets:22613 errors:0 dropped:0 overruns:0 frame:0
TX packets:38687 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1526267 (1.4 Mb) TX bytes:49122693 (46.8 Mb)
eth1 Link encap:Ethernet HWaddr 02:00:00:00:00:02
inet addr:10.115.137.51 Bcast:10.115.137.255 Mask:255.255.255.0
inet6 addr: fe80::200:0:a00:2/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1400 Metric:1
RX packets:650 errors:0 dropped:0 overruns:0 frame:0
TX packets:214 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:55932 (54.6 Kb) TX bytes:14424 (14.0 Kb)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:62 errors:0 dropped:0 overruns:0 frame:0
TX packets:62 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4300 (4.1 Kb) TX bytes:4300 (4.1 Kb)
I have turned off the firewall, and set ipforwarding on. I have been able
to display ospf neighbors from ospfd.
I have installed src_vipa, using yast, but not sure if there are parms
that need to be tweeked. I read that src_vipa was a prereq.
Any ideas at all at what I should be looking at?
Thanks in advance.
Jim Barnett
United Health Technologies
Mainframe Systems
This e-mail, including attachments, may include confidential and/or
proprietary information, and may be used only by the person or entity to
which it is addressed. If the reader of this e-mail is not the intended
recipient or his or her authorized agent, the reader is hereby notified
that any dissemination, distribution or copying of this e-mail is
prohibited. If you have received this e-mail in error, please notify the
sender by replying to this message and delete this e-mail immediately.
----------------------------------------------------------------------
For LINUX-390 subscribe / signoff / archive access instructions,
send email to [EMAIL PROTECTED] with the message: INFO LINUX-390 or visit
http://www.marist.edu/htbin/wlvindex?LINUX-390
