> > (let me know if these questions are getting tedious- I can
> > then go and try and figure it all out w/o bugging you...)
>
> Not at all.
>
> > ... At any rate,
> > the same disk boots fine on the alphaPC164 and a NoName..
>
> Ok, I misunderstood the problem then.
>
> > setting affinity to the primary CPU
> > jumping to bootstrap code
> >
> > halted CPU 0
>
> Well, it looks like a panic before normal console initialization.
>
> You might try using srm_printk to see if setup_arch is getting
> the machine identified ok. If that's ok, then you can use that
> CONFIG_EARLY_SERIAL_CONSOLE patch I sent earlier to track how
> far things get before crapping out.
I'm not sure it's even getting to load anything off the disk- it sure
identifies the system fine- on an alternate track I'm trying to get this
thing running after having loaded vmlinux from a *different* disk (I'm
stuck in rootdev hell- it doesn't seem to be parsing the command line in
this case (where I said root=/dev/sdb1)... well, a couple more tries and
I'll get it- but it certainly sees and understands this 4100:
P00>>>b dkb0 -fi vmlinux -fl 'root=/dev/sdb1'
Initializing...
SROM V3.0 on cpu0
XSROM V5.1 on cpu0
BCache testing complete on cpu0
mem_pair0 - 512 MB
20..21..23..
please wait 18 seconds for T24 to complete
24..
Memory testing complete on cpu0
starting console on CPU 0
sizing memory
0 512 MB EDO
probing IOD1 hose 1
bus 0 slot 1 - NCR 53C810
bus 0 slot 2 - NCR 53C825
bus 0 slot 4 - DECchip 21140-AA
bus 0 slot 5 - Ethernet Controller
probing IOD0 hose 0
bus 0 slot 1 - PCEB
probing EISA Bridge, bus 1
bus 0 slot 2 - QLogic ISP1020
bus 0 slot 4 - QLogic ISP1020
probing IOD3 hose 3
bus 0 slot 2 - QLogic ISP1020
bus 0 slot 4 - Ethernet Controller
probing IOD2 hose 2
bus 0 slot 2 - QLogic ISP1020
bus 0 slot 3 - QLogic ISP1020
bus 0 slot 4 - QLogic ISP1020
configuring I/O adapters...
ncr0, hose 1, bus 0, slot 1
ncr1, hose 1, bus 0, slot 2
tulip0, hose 1, bus 0, slot 4
floppy0, hose 0, bus 1, slot 0
isp0, hose 0, bus 0, slot 2
isp1, hose 0, bus 0, slot 4
isp2, hose 3, bus 0, slot 2
isp3, hose 2, bus 0, slot 2
isp4, hose 2, bus 0, slot 3
isp5, hose 2, bus 0, slot 4
System temperature is 24 degrees C
AlphaServer 4100 Console V5.1-3, 4-FEB-1998 16:40:08
CPU 0 booting
(boot dkb0.0.0.2.1 -file vmlinux -flags serial)
block 0 of dkb0.0.0.2.1 is a valid boot block
reading 15 blocks from dkb0.0.0.2.1
bootstrap code read in
Building FRU table
base = 200000, image_start = 0, image_bytes = 1e00
initializing HWRPB at 2000
initializing page table at 1f2000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
NetBSD/Alpha 1.3H Primary Boot +
Jumping to entry point...
NetBSD/Alpha Secondary Boot, Revision 1.9
([EMAIL PROTECTED], Sun Jun 28 15:39:07 PDT 1998)
VMS PAL rev: 0x4000e00010113
OSF PAL rev: 0x4001600020115
Switch to OSF PAL code succeeded.
Loading vmlinux.......
(LONG LINE ELIDED)
Entering vmlinux at 0xfffffc0000310000...
Linux version 2.2.1-mj0 ([EMAIL PROTECTED]) (gcc version egcs-2.90.29 980515
(egcs-1.0.3 release)) #9 Tue Feb 2 16:17:55 PST 1999
Booting on Rawhide variation Dodge using machine vector Rawhide (typ 16 var 865)
Command line: root=/dev/sdb1
mcpcia_init_arch: found 2 hoses
Turning on RTC interrupts.
Calibrating delay loop... 396.36 BogoMIPS
Memory: 515048k available
POSIX conformance testing by UNIFIX
Alpha PCI BIOS32 revision 0.04
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
Starting kswapd v 1.5
initialize_kbd: Keyboard reset failed, no ACK
Serial driver version 4.27 with<4>Keyboard timeout[2]
Keyboard timeout[2]
no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
Floppy drive(s): fd0 is 2.88M
FDC 0 is a National Semiconductor PC87306
md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8
linear personality registered
raid0 personality registered
raid1 personality registered
raid5 personality registered
ncr53c8xx: at PCI bus 1, device 1, function 0
ncr53c8xx: 53c810 detected
ncr53c8xx: at PCI bus 1, device 2, function 0
ncr53c8xx: 53c825 detected
ncr53c810-0: rev=0x02, base=0x104200000, io_port=0x100009000, irq=56
ncr53c810-0: ID 7, Fast-10, Parity Checking
ncr53c810-0: restart (scsi reset).
ncr53c825-1: rev=0x02, base=0x104201000, io_port=0x100009800, irq=40
ncr53c825-1: ID 7, Fast-10, Parity Checking
ncr53c825-1: restart (scsi reset).
scsi0 : ncr53c8xx - revision 3.1f
scsi1 : ncr53c8xx - revision 3.1f
scsi : 2 hosts.
Vendor: DEC Model: RRD46 (C) DEC Rev: 1337
Type: CD-ROM ANSI SCSI revision: 02
Vendor: SEAGATE Model: ST15230N Rev: 0638
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi1, channel 0, id 0, lun 0
Vendor: SEAGATE Model: ST15230N Rev: 0638
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi1, channel 0, id 4, lun 0
Vendor: SEAGATE Model: ST15230N Rev: 0638
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdc at scsi1, channel 0, id 5, lun 0
ncr53c825-1-<0,0>: tagged command queue depth set to 8
ncr53c825-1-<4,0>: tagged command queue depth set to 8
ncr53c825-1-<5,0>: tagged command queue depth set to 8
scsi : detected 3 SCSI disks total.
ncr53c825-1-<0,*>: FAST-10 SCSI 10.0 MB/s (100 ns, offset 8)
SCSI device sda: hdwr sector= 512 bytes. Sectors= 8386733 [4095 MB] [4.1 GB]
ncr53c825-1-<4,*>: FAST-10 SCSI 10.0 MB/s (100 ns, offset 8)
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 8386733 [4095 MB] [4.1 GB]
ncr53c825-1-<5,*>: FAST-10 SCSI 10.0 MB/s (100 ns, offset 8)
SCSI device sdc: hdwr sector= 512 bytes. Sectors= 8386733 [4095 MB] [4.1 GB]
eth0: DE500-AA at 0x10000a000 (PCI bus 1, device 4), h/w address 00:00:f8:1a:43:fe,
and requires IRQ48 (provided by PCI BIOS).
de4x5.c:V0.543 1998/12/30 [EMAIL PROTECTED]
Partition check:
sda: sda1 sda2 sda3 sda5
sdb: sdb1 sdb2 sdb3 sdb5
sdc:magic: c339c339
unknown partition table
You didn't specify the type of your ufs filesystem
mount -t ufs -o ufstype=sun|44bsd|old|next|openstep ....
>>>WARNING<<< Wrong ufstype may corrupt your filesystem, default is ufstype=old
ufs_read_super: bad magic number
Kernel panic: VFS: Unable to mount root fs on 08:02
halted CPU 0
halt code = 5
HALT instruction executed
PC = fffffc0000310088
