On 07/13/2015 05:25 PM, Dmitry Torokhov wrote:
@@ -76,6 +131,220 @@ static int __maybe_unused pmic8xxx_pwrkey_resume(struct device *dev) static SIMPLE_DEV_PM_OPS(pm8xxx_pwr_key_pm_ops, pmic8xxx_pwrkey_suspend, pmic8xxx_pwrkey_resume);+static void pmic8xxx_pwrkey_shutdown(struct platform_device *pdev)+{ + struct pmic8xxx_pwrkey *pwrkey = platform_get_drvdata(pdev); + int ret; + u8 mask, val; + bool reset = system_state == SYSTEM_RESTART; + + if (pwrkey->shutdown_fn) { + ret = pwrkey->shutdown_fn(pwrkey, reset); + if (ret) + return;Can we call this variable "error" please?
Ok.
+ } + + /* + * Select action to perform (reset or shutdown) when PS_HOLD goes low. + * Also ensure that KPD, CBL0, and CBL1 pull ups are enabled and that + * USB charging is enabled. + */ + mask = PON_CNTL_1_PULL_UP_EN | PON_CNTL_1_USB_PWR_EN; + mask |= PON_CNTL_1_WD_EN_RESET; + val = mask; + if (!reset) + val &= ~PON_CNTL_1_WD_EN_RESET; + + regmap_update_bits(pwrkey->regmap, PON_CNTL_1, mask, val); +} + +/* + * Set an SMPS regulator to be disabled in its CTRL register, but enabled + * in the master enable register. Also set it's pull down enable bit. + * Take care to make sure that the output voltage doesn't change if switching + * from advanced mode to legacy mode. + */ +static int pm8058_disable_smps_locally_set_pull_down(struct regmap *regmap, + u16 ctrl_addr, u16 test2_addr, u16 master_enable_addr, + u8 master_enable_bit) +{ + int ret = 0;Why does it need to be initialized? And "error" too please.
Doesn't need to be.
+ + /* Enable LDO in master control register. */ + ret = regmap_update_bits(regmap, master_enable_addr, + master_enable_bit, master_enable_bit); + if (ret) + return ret; + + /* Disable LDO in CTRL register and set pull down */ + return regmap_update_bits(regmap, ctrl_addr, + PM8058_REGULATOR_ENABLE_MASK | PM8058_REGULATOR_PULL_DOWN_MASK, + PM8058_REGULATOR_DISABLE | PM8058_REGULATOR_PULL_DOWN_EN); +} + +static int pm8058_pwrkey_shutdown(struct pmic8xxx_pwrkey *pwrkey, bool reset) +{ + int ret;And here.
Ok.
+ struct regmap *regmap = pwrkey->regmap; + u8 mask, val; + + /* When shutting down, enable active pulldowns on important rails. */ + if (!reset) { + /* Disable SMPS's 0,1,3 locally and set pulldown enable bits. */ + pm8058_disable_smps_locally_set_pull_down(regmap, + PM8058_S0_CTRL, PM8058_S0_TEST2, + REG_PM8058_VREG_EN_MSM, BIT(7)); + pm8058_disable_smps_locally_set_pull_down(regmap, + PM8058_S1_CTRL, PM8058_S1_TEST2, + REG_PM8058_VREG_EN_MSM, BIT(6)); + pm8058_disable_smps_locally_set_pull_down(regmap, + PM8058_S3_CTRL, PM8058_S3_TEST2, + REG_PM8058_VREG_EN_GRP_5_4, BIT(7) | BIT(4)); + /* Disable LDO 21 locally and set pulldown enable bit. */ + pm8058_disable_ldo_locally_set_pull_down(regmap, + PM8058_L21_CTRL, REG_PM8058_VREG_EN_GRP_5_4, + BIT(1)); + } + + /* + * Fix-up: Set regulator LDO22 to 1.225 V in high power mode. Leave its + * pull-down state intact. This ensures a safe shutdown. + */ + ret = regmap_update_bits(regmap, PM8058_L22_CTRL, 0xbf, 0x93); + if (ret) + return ret; + + /* Enable SMPL if resetting is desired */ + mask = SLEEP_CTRL_SMPL_EN_RESET; + val = 0; + if (reset) + val = mask; + return regmap_update_bits(regmap, PM8058_SLEEP_CTRL, mask, val); +Stray empty line.
Ok.
+} + +static int pm8921_pwrkey_shutdown(struct pmic8xxx_pwrkey *pwrkey, bool reset) +{ + struct regmap *regmap = pwrkey->regmap; + u8 mask = SLEEP_CTRL_SMPL_EN_RESET; + u8 val = 0; + + /* Enable SMPL if resetting is desired */ + if (reset) + val = mask; + return regmap_update_bits(regmap, PM8921_SLEEP_CTRL, mask, val); +} + +static const struct of_device_id pm8xxx_pwr_key_id_table[] = { + { .compatible = "qcom,pm8058-pwrkey", .data = &pm8058_pwrkey_shutdown }, + { .compatible = "qcom,pm8921-pwrkey", .data = &pm8921_pwrkey_shutdown }, + { } +}; +MODULE_DEVICE_TABLE(of, pm8xxx_pwr_key_id_table); +Can we please keep IDs and device table where it was, close to the driver definition?
That would require forward declaring the array here. Is that desired? I moved it so that I could use it in the probe function.
-- Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
