About the first error , you probably should leave assabet powered
off for five minutes. Sometimes it takes
that much time for the capacitor to discharge. I face this problem
pretty often. I leave it off for atleast
five minutes and then I can flash it.
About the second problem, when you boot using blob, make sure you set
the serial port speed to 115K
I think it is CTRL-A O E I if I remember right. Then switch to another
console and uuencode zImage zImage >/dev/modem
or /dev/ttyS0 or whatever it is. Minicom will print lotsa .... and
finally blob will tell you to switch back to
9600B, CTRL A O E E should do it. Repeat the same for RAMDISK as well.
Hope this helps you.
Greetings
vinny
Gad Hayisraeli wrote:
> hello.
> i need help !
> i tried several utilities in order to download :
> 1. boot loader (angel , angel 2.08, blob 2.07, 2.08 pre2)
> 2. kernel
> 3. ramdisk
>
> i tried to use several versions of angelboot, but i got always this error:
>
> "Error: Received 1d when expecting start packet character."
>
> i tried all sorts of "opts" file ! - always the same error.
> i tried to check the lpt1, and com2, which i'm using, and also i tried com1
> - but the same.
>
> then i tried the jflash-linux, and then i received this error:
>
> ====================
> [root@Linux-Gad angel-1.00]# ./Jflash-linux angel208a.bin
> error, failed to read device ID
> ACT: 0000 0000100000001010 00000010101 1
> EXP: 0000 0000000000011010 00000010101 1
>
> failed to read device ID for the PZ3032
> [root@Linux-Gad angel-1.00]# ./Jflash-linux angel208a.bin
> error, failed to read device ID
> ACT: 1111 1111111111111111 11111111111 1
> EXP: 0101 1001001001100001 00000001001 1
>
> failed to read device ID for the SA-1110
> =================================
>
> then i switched to windows and used the jflash of intel.
> i succeeded only to download blob, 2.0.8, pre2, and i saw in the terminal
> that its working.
> i also tried downloading angel, but then i dont know how to continue
> downloading the kernel with jflash to the target ?
>
> after downloding blob, i tried to download the kernel with "download kernel"
> command.
> i acted accroding the instructions of the blob readme, but:
> a. if i used minicom and downloaded in 115200, ascii foprmat, i received in
> the minicom download window:
> " 0.0 Kbytes transferred at 0 CPS �^+� '�' +/�^ +�U " J= �"
>
> " 387.6 Kbytes transferred at 396924 CPS... Done.�=I/c/+"
> while the kernel size is 620k ! and the CPS seems to be wrong ...
>
> i tried to use "uuencode ..... > /dev/ttyS1" method but then i received
> this error:
>
> ========================
> blob> download kernel
>
> Switching to 115200 baud
>
> You have 60 seconds to switch your terminal emulator to the same speed and
> start downloading. After that blob will switch back to 9600 baud.
>
> ..??
> �>..~.>...�>?�.�.>�>.~..>...>..��>.�...�.�.>..�..�����>...�>....���^~..^�..�
> ...?.?��>�>.�.~>..�.>..�....?�..�>?�>��.��.......�.N�..�.~.�>�-B?j磫9�.?...?
> I�C.bC.B.N-�9�)�.� /....blob> ###I###########"IP,Y_E
> *** Unknown command: I"IP,Y_E
> blob> M`""3Y0$`TN$<0`PE^4G`$OE$`!1X04``"I`
> *** Unknown command: M`""3Y0$`TN<0`PE^4G`$OE`!1X04``"I`
> ============================================
> in every download speed, after receiving approx. 2000 bytes, i got " unknown
> command" and the blob returns to its shell without even displaying "uudecode
> failed" ?
>
> these are my questions. please help.
>
> Regards,
>
> Gad Hayisraeli
> C.T.O.
> SoftGen Ltd.
> E-Mail: [EMAIL PROTECTED]
>
> winmail.dat
>
> Content-Type:
>
> application/ms-tnef
> Content-Encoding:
>
> base64
>
>
_______________________________________________
http://lists.arm.linux.org.uk/mailman/listinfo/linux-arm
Please visit the above address for information on this list.
