Hi,
The steps I did are:
1 .Go through the instruction on
http://www.cs.cmu.edu/~wearable/software/assabet.html
2. Download the file
3. Config minicom (refer to www.mvista.com and use the instructiuon in
Hardhat CDK1.2
4. Port JTAG following intel instruction.Note: Copy the Angel.bin file to
the same folder as JTAG
5. Connect the serial port 1 to the board
6. configure angel referring to the file in /linux/documentation/arm/assabet
if you have 2.4.0 kernel
7. Reboot in linux mount window partition by typing"mount /dev/hda1 /mnt"
8. modify ramdisk using intel brutus (sa1100) instruction
9. in the directory type " make"
10. "./angleboot -f dotangelrc zImage-assabet"
11. run " minicom"
12 login type "root" in minicom
13. then tpye " cd .." then "ls"
14. after see all the excutable file you can run it and enjoy.
15. there are some other arm excutable in the angel folder mount it to the
ramdisk following intel instruction.
Hope it will help you.
regards,
Xiaoyong
-----Original Message-----
From: Vinodh D Rajan [mailto:[EMAIL PROTECTED]]
Sent: Friday, January 05, 2001 9:36 PM
To: [EMAIL PROTECTED]
Cc: [EMAIL PROTECTED]
Subject: Re: problems downloading to assabet sa-1110
About the first error , you probably should leave assabet powered
off for five minutes. Sometimes it takes
that much time for the capacitor to discharge. I face this problem
pretty often. I leave it off for atleast
five minutes and then I can flash it.
About the second problem, when you boot using blob, make sure you set
the serial port speed to 115K
I think it is CTRL-A O E I if I remember right. Then switch to another
console and uuencode zImage zImage >/dev/modem
or /dev/ttyS0 or whatever it is. Minicom will print lotsa .... and
finally blob will tell you to switch back to
9600B, CTRL A O E E should do it. Repeat the same for RAMDISK as well.
Hope this helps you.
Greetings
vinny
Gad Hayisraeli wrote:
> hello.
> i need help !
> i tried several utilities in order to download :
> 1. boot loader (angel , angel 2.08, blob 2.07, 2.08 pre2)
> 2. kernel
> 3. ramdisk
>
> i tried to use several versions of angelboot, but i got always this error:
>
> "Error: Received 1d when expecting start packet character."
>
> i tried all sorts of "opts" file ! - always the same error.
> i tried to check the lpt1, and com2, which i'm using, and also i tried
com1
> - but the same.
>
> then i tried the jflash-linux, and then i received this error:
>
> ====================
> [root@Linux-Gad angel-1.00]# ./Jflash-linux angel208a.bin
> error, failed to read device ID
> ACT: 0000 0000100000001010 00000010101 1
> EXP: 0000 0000000000011010 00000010101 1
>
> failed to read device ID for the PZ3032
> [root@Linux-Gad angel-1.00]# ./Jflash-linux angel208a.bin
> error, failed to read device ID
> ACT: 1111 1111111111111111 11111111111 1
> EXP: 0101 1001001001100001 00000001001 1
>
> failed to read device ID for the SA-1110
> =================================
>
> then i switched to windows and used the jflash of intel.
> i succeeded only to download blob, 2.0.8, pre2, and i saw in the terminal
> that its working.
> i also tried downloading angel, but then i dont know how to continue
> downloading the kernel with jflash to the target ?
>
> after downloding blob, i tried to download the kernel with "download
kernel"
> command.
> i acted accroding the instructions of the blob readme, but:
> a. if i used minicom and downloaded in 115200, ascii foprmat, i received
in
> the minicom download window:
> " 0.0 Kbytes transferred at 0 CPS �^+� '�' +/�^ +?U " J= �"
>
> " 387.6 Kbytes transferred at 396924 CPS... Done.�=I/c/+"
> while the kernel size is 620k ! and the CPS seems to be wrong ...
>
> i tried to use "uuencode ..... > /dev/ttyS1" method but then i received
> this error:
>
> ========================
> blob> download kernel
>
> Switching to 115200 baud
>
> You have 60 seconds to switch your terminal emulator to the same speed and
> start downloading. After that blob will switch back to 9600 baud.
>
> ..??
>
AE>..~.>...AE>?AE.AE.>AE>.~..>...>..AEAE>.AE...AE.AE.>..AE..AEAEAEAEAE>...AE
>....AEAEAE^~..^AE..?
>
...?.??AE>AE>.AE.~>..?.>..AE....?AE..AE>?AE>?AE.AEAE.......AE.NAE..AE.~.AE>�
-B?j?��9AE.?...?
> I?C.bC.B.N-�9AE)?.� /....blob> ###I###########"IP,Y_E
> *** Unknown command: I"IP,Y_E
> blob> M`""3Y0$`TN$<0`PE^4G`$OE$`!1X04``"I`
> *** Unknown command: M`""3Y0$`TN<0`PE^4G`$OE`!1X04``"I`
> ============================================
> in every download speed, after receiving approx. 2000 bytes, i got "
unknown
> command" and the blob returns to its shell without even displaying
"uudecode
> failed" ?
>
> these are my questions. please help.
>
> Regards,
>
> Gad Hayisraeli
> C.T.O.
> SoftGen Ltd.
> E-Mail: [EMAIL PROTECTED]
>
> winmail.dat
>
> Content-Type:
>
> application/ms-tnef
> Content-Encoding:
>
> base64
>
>
_______________________________________________
http://lists.arm.linux.org.uk/mailman/listinfo/linux-arm
Please visit the above address for information on this list.
_______________________________________________
http://lists.arm.linux.org.uk/mailman/listinfo/linux-arm
Please visit the above address for information on this list.
