Linux-Development-Sys Digest #285, Volume #6 Fri, 15 Jan 99 08:14:07 EST
Contents:
read from scsi tape crashes system (Mario Dix)
----------------------------------------------------------------------------
From: Mario Dix <[EMAIL PROTECTED]>
Crossposted-To: linux.dev.scsi
Subject: read from scsi tape crashes system
Date: Thu, 14 Jan 1999 19:22:25 +0100
This is a multi-part message in MIME format.
==============3DACA717C3537A89769C6639
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit
I used to run Linux on a Pentium 133 w 64M Ram. I am using Linux since
0.99.12. Never had serious problems. But this changed.
Christmas I upgraded to AMD K6-400 (Stepping 12) , 256 MB Ram (PC-100),
FIC PA-2013 Motherboard (1 Mb cache, VIA MP3 chipset), scsi from the old
box.
RH5.2
Since christmas I am struggling to get a stable system. It is a
nightmare. I am geeting quite often kernel paging request errors. It
does not seem to be a kernel problem, because it shows the same
behaviour with 2.0.36 and 2.2-pre3 and pre5.
First I suspected that the RAM is not able to run at 100 Mhz, so I
decreased the frequency to 66 Mhz. No difference.
The most annoying thing is now, that I obviously can not restore
anything from tape anymore. I am doing tape backups every night with
BRU. The "brulog" does not show any errors when it writes to tape, but
it complains when it starts to verify.
Also when I try to restore something from tape it crashes and after a
while the systems hangs.
I have no clue anymore.
Any suggestions?
--
Mario Dix / Kirsteinstrasse 54A / 12559 Berlin / Germany / Tel +49 30 65908113
==============3DACA717C3537A89769C6639
Content-Type: text/plain; charset=us-ascii; name="foo"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline; filename="foo"
Jan 13 00:52:50 albundy syslogd 1.3-3: restart (remote reception).
Jan 13 00:52:50 albundy kernel: klogd 1.3-3, log source = /proc/kmsg started.
Jan 13 00:52:50 albundy kernel: Cannot find map file.
Jan 13 00:52:50 albundy kernel: Error seeking in /dev/kmem
Jan 13 00:52:50 albundy kernel: Error adding kernel module table entry.
Jan 13 00:52:50 albundy kernel: Linux version 2.2.0-pre5 (root@albundy) (gcc version
2.7.2.3) #1 Thu Jan 7 21:11:50 CET 1999
Jan 13 00:52:50 albundy kernel: Detected 400918422 Hz processor.
Jan 13 00:52:50 albundy kernel: Console: colour VGA+ 80x25
Jan 13 00:52:50 albundy kernel: Calibrating delay loop... 799.54 BogoMIPS
Jan 13 00:52:50 albundy kernel: Memory: 257460k/262080k available (860k kernel code,
412k reserved, 3292k data, 56k init)
Jan 13 00:52:50 albundy kernel: CPU: AMD AMD-K6(tm) 3D processor stepping 0c
Jan 13 00:52:50 albundy kernel: Checking 386/387 coupling... OK, FPU using exception
16 error reporting.
Jan 13 00:52:50 albundy kernel: Checking 'hlt' instruction... OK.
Jan 13 00:52:50 albundy kernel: POSIX conformance testing by UNIFIX
Jan 13 00:52:50 albundy kernel: PCI: PCI BIOS revision 2.10 entry at 0xfb490
Jan 13 00:52:50 albundy kernel: PCI: Using configuration type 1
Jan 13 00:52:50 albundy kernel: PCI: Probing PCI hardware
Jan 13 00:52:50 albundy kernel: PCI: 00:38 [1106/0586]: Work around ISA DMA hangs (00)
Jan 13 00:52:50 albundy kernel: Activating ISA DMA hang workarounds.
Jan 13 00:52:50 albundy kernel: Linux NET4.0 for Linux 2.2
Jan 13 00:52:50 albundy kernel: Based upon Swansea University Computer Society NET3.039
Jan 13 00:52:50 albundy kernel: NET4: Unix domain sockets 1.0 for Linux NET4.0.
Jan 13 00:52:50 albundy kernel: NET4: Linux TCP/IP 1.0 for NET4.0
Jan 13 00:52:50 albundy kernel: IP Protocols: ICMP, UDP, TCP
Jan 13 00:52:50 albundy kernel: Starting kswapd v 1.5
Jan 13 00:52:50 albundy kernel: Serial driver version 4.27 with no serial options
enabled
Jan 13 00:52:50 albundy kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A
Jan 13 00:52:50 albundy kernel: ttyS01 at 0x02f8 (irq = 3) is a 16550A
Jan 13 00:52:50 albundy kernel: pty: 256 Unix98 ptys configured
Jan 13 00:52:50 albundy kernel: Floppy drive(s): fd0 is 1.44M
Jan 13 00:52:50 albundy kernel: FDC 0 is a post-1991 82077
Jan 13 00:52:50 albundy kernel: ncr53c8xx: at PCI bus 0, device 10, function 0
Jan 13 00:52:50 albundy kernel: ncr53c8xx: 53c825 detected
Jan 13 00:52:50 albundy kernel: ncr53c825-0: rev=0x02, base=0xec000000,
io_port=0xe000, irq=5
Jan 13 00:52:50 albundy kernel: ncr53c825-0: ID 7, Fast-10, Parity Checking
Jan 13 00:52:50 albundy kernel: ncr53c825-0: restart (scsi reset).
Jan 13 00:52:50 albundy kernel: EATA0: address 0xe010 in use, skipping probe.
Jan 13 00:52:50 albundy kernel: EATA/DMA 2.0x: Copyright (C) 1994-1998 Dario Ballabio.
Jan 13 00:52:50 albundy kernel: EATA config options -> tc:y, lc:y, mq:16, eh:y, rs:y,
et:n.
Jan 13 00:52:50 albundy kernel: EATA0: 2.0C, PCI 0xd810, IRQ 10, BMST, SG 122, MB 64.
Jan 13 00:52:50 albundy kernel: EATA0: wide SCSI support enabled, max_id 16, max_lun 8.
Jan 13 00:52:50 albundy kernel: EATA0: SCSI channel 0 enabled, host target ID 7.
Jan 13 00:52:50 albundy kernel: EATA0: SCSI channel 1 enabled, host target ID 7.
Jan 13 00:52:50 albundy kernel: scsi0 : ncr53c8xx - revision 3.1d
Jan 13 00:52:50 albundy kernel: scsi1 : EATA/DMA 2.0x rev. 4.33.00
Jan 13 00:52:50 albundy kernel: scsi : 2 hosts.
Jan 13 00:52:50 albundy kernel: Vendor: HP Model: C1537A Rev: L610
Jan 13 00:52:50 albundy kernel: Type: Sequential-Access ANSI SCSI
revision: 02
Jan 13 00:52:50 albundy kernel: Vendor: PIONEER Model: CD-ROM DR-U03S Rev: 1.01
Jan 13 00:52:50 albundy kernel: Type: CD-ROM ANSI SCSI
revision: 02
Jan 13 00:52:50 albundy kernel: Vendor: DPT Model: RAID-A Rev: 07L0
Jan 13 00:52:50 albundy kernel: Type: Direct-Access ANSI SCSI
revision: 02
Jan 13 00:52:50 albundy kernel: Detected scsi disk sda at scsi1, channel 0, id 1, lun 0
Jan 13 00:52:50 albundy kernel: Vendor: DPT Model: RAID-B Rev: 07L0
Jan 13 00:52:50 albundy kernel: Type: Direct-Access ANSI SCSI
revision: 02
Jan 13 00:52:50 albundy kernel: Detected scsi disk sdb at scsi1, channel 1, id 0, lun 0
Jan 13 00:52:50 albundy kernel: EATA0: scsi1, channel 0, id 1, lun 0, cmds/lun 16,
sorted, tagged.
Jan 13 00:52:50 albundy kernel: EATA0: scsi1, channel 1, id 0, lun 0, cmds/lun 16,
sorted, tagged.
Jan 13 00:52:50 albundy kernel: scsi : detected 2 SCSI disks total.
Jan 13 00:52:50 albundy kernel: SCSI device sda: hdwr sector= 512 bytes. Sectors=
17915728 [8747 MB] [8.7 GB]
Jan 13 00:52:50 albundy kernel: SCSI device sdb: hdwr sector= 512 bytes. Sectors=
17915728 [8747 MB] [8.7 GB]
Jan 13 00:52:50 albundy kernel: tulip.c:v0.89H 5/23/98 [EMAIL PROTECTED]
Jan 13 00:52:50 albundy kernel: eth0: Digital DS21140 Tulip at 0xdc00, 00 80 c8 94 41
a8, IRQ 11.
Jan 13 00:52:50 albundy kernel: eth0: EEPROM default media type Autosense.
Jan 13 00:52:50 albundy kernel: eth0: Index #0 - Media MII (#11) described by a 21140
MII PHY (1) block.
Jan 13 00:52:50 albundy kernel: eth0: MII transceiver found at MDIO address 0, config
1000 status 782d.
Jan 13 00:52:50 albundy kernel: Partition check:
Jan 13 00:52:50 albundy kernel: sda: sda1 sda2 sda3 sda4
Jan 13 00:52:50 albundy kernel: sdb: sdb1 sdb2 sdb3 sdb4
Jan 13 00:52:50 albundy kernel: VFS: Mounted root (ext2 filesystem) readonly.
Jan 13 00:52:50 albundy kernel: Freeing unused kernel memory: 56k freed
Jan 13 00:52:50 albundy kernel: Adding Swap: 130748k swap-space (priority -1)
Jan 13 00:52:50 albundy kernel: st: bufsize 32768, wrt 30720, max buffers 4, s/g segs
16.
Jan 13 00:52:50 albundy kernel: Detected scsi tape st0 at scsi0, channel 0, id 3, lun 0
Jan 13 00:53:01 albundy mountd[312]: NFS mount of /.cfsfs attempted from 127.0.0.1
Jan 13 00:53:01 albundy mountd[312]: /.cfsfs has been mounted by 127.0.0.1
Jan 13 00:56:17 albundy kernel: ncr53c825-0-<3,*>: FAST-10 SCSI 10.0 MB/s (100 ns,
offset 8)
Jan 13 00:58:01 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=19004976 SSTAT1=6
Jan 13 00:58:01 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 00:58:01 albundy kernel: Additional sense indicates Data phase error
............................. cut ...........................
Jan 13 01:04:55 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Not Ready
Jan 13 01:04:55 albundy kernel: Additional sense indicates Logical unit not ready,
cause not reportable
Jan 13 01:04:58 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Not Ready
Jan 13 01:04:58 albundy kernel: Additional sense indicates Logical unit not ready,
cause not reportable
Jan 13 01:05:01 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Not Ready
Jan 13 01:05:01 albundy kernel: Additional sense indicates Logical unit not ready,
cause not reportable
Jan 13 01:05:04 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Not Ready
Jan 13 01:05:04 albundy kernel: Additional sense indicates Logical unit not ready,
cause not reportable
Jan 13 08:03:29 albundy kernel: EXT2-fs error (device 08:11): ext2_find_entry: bad
entry in directory #765986: inode out of bounds - offset=1444, inode=134983776,
rec_len=20, name_len=9
Jan 13 08:03:29 albundy kernel: EXT2-fs error (device 08:11): ext2_find_entry: bad
entry in directory #765986: inode out of bounds - offset=868, inode=135090203,
rec_len=12, name_len=4
Jan 13 08:04:56 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=19000df5 SSTAT1=6
Jan 13 08:04:56 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 08:04:56 albundy kernel: Additional sense indicates Data phase error
.................... cut ...........................
Jan 13 08:14:09 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 08:14:09 albundy kernel: Additional sense indicates Data phase error
Jan 13 08:14:12 albundy kernel: ncr53c825-0:3: ERROR (0:14) (0-a7-80) (8/13) @ (script
3c4:50000000).
Jan 13 08:14:12 albundy kernel: ncr53c825-0: script cmd = 80000000
Jan 13 08:14:12 albundy kernel: ncr53c825-0: regdump: da 10 80 13 47 08 03 0f 35 00 83
a7 80 00 07 02.
Jan 13 08:14:12 albundy kernel: ncr53c825-0: have to clear fifos.
Jan 13 08:14:12 albundy kernel: ncr53c825-0: unexpected disconnect
Jan 13 08:14:14 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=19004ed5 SSTAT1=6
Jan 13 08:14:14 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 08:14:14 albundy kernel: Additional sense indicates Data phase error
Jan 13 08:14:18 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=190016d5 SSTAT1=6
Jan 13 08:14:18 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
.............. cut ...............
Jan 13 10:27:25 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=19002b95 SSTAT1=6
Jan 13 10:27:25 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 10:27:25 albundy kernel: Additional sense indicates Data phase error
Jan 13 10:27:28 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=190015d5 SSTAT1=6
Jan 13 10:27:28 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 10:27:28 albundy kernel: Additional sense indicates Data phase error
Jan 13 10:27:30 albundy kernel: Unable to handle kernel paging request at virtual
address 453e4f34
Jan 13 10:27:30 albundy kernel: current->tss.cr3 = 00101000, pr3 = 00101000
Jan 13 10:27:30 albundy kernel: *pde = 00000000
Jan 13 10:27:30 albundy kernel: Oops: 0000
Jan 13 10:27:30 albundy kernel: CPU: 0
Jan 13 10:27:30 albundy kernel: EIP: 0010:[<c0123e4a>]
Jan 13 10:27:30 albundy kernel: EFLAGS: 00010207
Jan 13 10:27:30 albundy kernel: eax: 453e4f20 ebx: c04978e0 ecx: 00000006 edx:
0001ffe0
Jan 13 10:27:30 albundy kernel: esi: 453e4f20 edi: cd3d9060 ebp: c04978e0 esp:
c052dfa4
Jan 13 10:27:30 albundy kernel: ds: 0018 es: 0018 ss: 0018
Jan 13 10:27:30 albundy kernel: Process kswapd (pid: 3, process nr: 3,
stackpage=c052d000)
Jan 13 10:27:30 albundy kernel: Stack: 00000000 00009000 c0119846 c04978e0 0000000d
00000006 c011e40f 00000006
Jan 13 10:27:30 albundy kernel: 00000000 00000000 c01b8783 c052c000 c011e3d9
00000000 00000010 00000f00
Jan 13 10:27:30 albundy kernel: c009dfc0 c0106000 c052c000 c010650f 00000000
00000f00 c01effd8
Jan 13 10:27:30 albundy kernel: Call Trace: [<c0119846>] [<c011e40f>] [<c01b8783>]
[<c011e3d9>] [<c0106000>] [<c010650f>]
Jan 13 10:27:30 albundy kernel: Code: 8b 76 14 83 78 20 00 75 06 f6 40 18 46 74 13 6a
00 e8 3c 01
Jan 13 10:27:32 albundy kernel: Unable to handle kernel paging request at virtual
address e53e4e74
Jan 13 10:27:32 albundy kernel: current->tss.cr3 = 0bd1c000, pr3 = 0bd1c000
Jan 13 10:27:32 albundy kernel: *pde = 00000000
Jan 13 10:27:32 albundy kernel: Oops: 0000
Jan 13 10:27:32 albundy kernel: CPU: 0
Jan 13 10:27:32 albundy kernel: EIP: 0010:[<c0123e4a>]
Jan 13 10:27:32 albundy kernel: EFLAGS: 00010206
Jan 13 10:27:32 albundy kernel: eax: e53e4e60 ebx: c0497910 ecx: 00000006 edx:
0001ffe0
Jan 13 10:27:32 albundy kernel: esi: e53e4e60 edi: cd3e4ec0 ebp: c0497910 esp:
c3d25e58
Jan 13 10:27:32 albundy kernel: ds: 0018 es: 0018 ss: 0018
Jan 13 10:27:32 albundy kernel: Process bru (pid: 1320, process nr: 48,
stackpage=c3d25000)
Jan 13 10:27:32 albundy kernel: Stack: 00000005 00000801 c0119846 c0497910 00000020
00000006 c011e40f 00000006
Jan 13 10:27:32 albundy kernel: 00000005 c3d24000 00000200 00000000 c011ec3d
00000005 00000020 00000000
Jan 13 10:27:32 albundy kernel: 00000200 00000000 00000801 00000005 00000801
c0122cfb 00000801 00000000
Jan 13 10:27:32 albundy kernel: Call Trace: [<c0119846>] [<c011e40f>] [<c011ec3d>]
[<c0122cfb>] [<c0123d83>] [<c0122ee4>] [<c0123176>]
Jan 13 10:27:32 albundy kernel: [<c013c84d>] [<c014044b>] [<c013e3d2>]
[<c013e21c>] [<d001f5ff>] [<c012197c>] [<c0107a20>]
Jan 13 10:27:32 albundy kernel: Code: 8b 76 14 83 78 20 00 75 06 f6 40 18 46 74 13 6a
00 e8 3c 01
Jan 13 10:27:47 albundy kernel: Unable to handle kernel paging request at virtual
address 453e4cf4
Jan 13 10:27:47 albundy kernel: current->tss.cr3 = 0bd1c000, pr3 = 0bd1c000
Jan 13 10:27:47 albundy kernel: *pde = 00000000
Jan 13 10:27:47 albundy kernel: Oops: 0000
Jan 13 10:27:47 albundy kernel: CPU: 0
Jan 13 10:27:47 albundy kernel: EIP: 0010:[<c0123e4a>]
Jan 13 10:27:47 albundy kernel: EFLAGS: 00010207
Jan 13 10:27:47 albundy kernel: eax: 453e4ce0 ebx: c0497970 ecx: 00000006 edx:
0001ffe0
Jan 13 10:27:47 albundy kernel: esi: 453e4ce0 edi: cd3e4d40 ebp: c0497970 esp:
c5bdfebc
Jan 13 10:27:47 albundy kernel: ds: 0018 es: 0018 ss: 0018
Jan 13 10:27:47 albundy kernel: Process lpr (pid: 1446, process nr: 48,
stackpage=c5bdf000)
Jan 13 10:27:47 albundy kernel: Stack: 00000003 00000000 c0119846 c0497970 0000001f
00000006 c011e40f 00000006
Jan 13 10:27:47 albundy kernel: 00000003 c5bde000 c02129b8 00000000 c011ec3d
00000003 00000020 ced5496c
Jan 13 10:27:47 albundy kernel: c02129b8 00000000 00000000 00000003 00000000
c0119f81 c5bdff80 00000000
Jan 13 10:27:47 albundy kernel: Call Trace: [<c0119846>] [<c011e40f>] [<c011ec3d>]
[<c0119f81>] [<c0119fb4>] [<c011a1dc>] [<c011a128>]
Jan 13 10:27:47 albundy kernel: [<c0121896>] [<c0107a20>]
Jan 13 10:27:47 albundy kernel: Code: 8b 76 14 83 78 20 00 75 06 f6 40 18 46 74 13 6a
00 e8 3c 01
Jan 13 10:27:54 albundy kernel: Unable to handle kernel paging request at virtual
address 473e4b74
Jan 13 10:27:54 albundy kernel: current->tss.cr3 = 0bd1c000, pr3 = 0bd1c000
Jan 13 10:27:54 albundy kernel: *pde = 00000000
Jan 13 10:27:54 albundy kernel: Oops: 0000
Jan 13 10:27:54 albundy kernel: CPU: 0
Jan 13 10:27:54 albundy kernel: EIP: 0010:[<c0123e4a>]
Jan 13 10:27:54 albundy kernel: EFLAGS: 00010207
Jan 13 10:27:54 albundy kernel: eax: 473e4b60 ebx: c04979a0 ecx: 00000006 edx:
0001ffe0
Jan 13 10:27:54 albundy kernel: esi: 473e4b60 edi: cd3e4bc0 ebp: c04979a0 esp:
c5bdfdb4
Jan 13 10:27:54 albundy kernel: ds: 0018 es: 0018 ss: 0018
Jan 13 10:27:54 albundy kernel: Process lpr (pid: 1448, process nr: 48,
stackpage=c5bdf000)
Jan 13 10:27:54 albundy kernel: Stack: 00000005 00020813 c0119846 c04979a0 00000020
00000006 c011e40f 00000006
Jan 13 10:27:54 albundy kernel: 00000005 c5bde000 00000400 00000001 c011ec3d
00000005 00000020 00000000
Jan 13 10:27:54 albundy kernel: 00000400 00000001 00020813 00000005 00000813
c0122cfb 00000813 00000000
Jan 13 10:27:54 albundy kernel: Call Trace: [<c0119846>] [<c011e40f>] [<c011ec3d>]
[<c0122cfb>] [<c0123d83>] [<c0122ee4>] [<c0123176>]
Jan 13 10:27:54 albundy kernel: [<c01378c9>] [<c0137d03>] [<c0138108>]
[<c01365a6>] [<c01363bc>] [<c011a11a>] [<c011a1dc>] [<c011a128>]
Jan 13 10:27:54 albundy kernel: [<c0121896>] [<c012197c>] [<c0107a20>]
Jan 13 10:27:54 albundy kernel: Code: 8b 76 14 83 78 20 00 75 06 f6 40 18 46 74 13 6a
00 e8 3c 01
Jan 13 10:28:00 albundy kernel: Unable to handle kernel paging request at virtual
address e53e49f4
Jan 13 10:28:00 albundy kernel: current->tss.cr3 = 0e3b3000, pr3 = 0e3b3000
Jan 13 10:28:00 albundy kernel: *pde = 00000000
Jan 13 10:28:00 albundy kernel: Oops: 0000
Jan 13 10:28:00 albundy kernel: CPU: 0
Jan 13 10:28:00 albundy kernel: EIP: 0010:[<c0123e4a>]
Jan 13 10:28:00 albundy kernel: EFLAGS: 00010206
Jan 13 10:28:00 albundy kernel: eax: e53e49e0 ebx: c0497a30 ecx: 00000006 edx:
0001ffe0
Jan 13 10:28:00 albundy kernel: esi: e53e49e0 edi: cd3e4a40 ebp: c0497a30 esp:
cbbebf3c
Jan 13 10:28:00 albundy kernel: ds: 0018 es: 0018 ss: 0018
Jan 13 10:28:00 albundy kernel: Process wish (pid: 1286, process nr: 56,
stackpage=cbbeb000)
Jan 13 10:28:00 albundy kernel: Stack: 00000005 bffff8e8 c0119846 c0497a30 0000001f
00000006 c011e40f 00000006
Jan 13 10:28:00 albundy kernel: 00000005 cbbea000 00000000 00000000 c011ec3d
00000005 00000020 fffffff4
Jan 13 10:28:00 albundy kernel: 00000000 00000000 bffff8e8 00000005 00000000
00000000 00000040 00000000
Jan 13 10:28:00 albundy kernel: Call Trace: [<c0119846>] [<c011e40f>] [<c011ec3d>]
[<c012a638>] [<c0107a20>]
Jan 13 10:28:00 albundy kernel: Code: 8b 76 14 83 78 20 00 75 06 f6 40 18 46 74 13 6a
00 e8 3c 01
Jan 13 11:58:27 albundy syslogd 1.3-3: restart (remote reception).
Jan 13 11:58:27 albundy kernel: klogd 1.3-3, log source = /proc/kmsg started.
Jan 13 11:58:27 albundy kernel: Cannot find map file.
Jan 13 11:58:27 albundy kernel: Error seeking in /dev/kmem
Jan 13 11:58:27 albundy kernel: Error adding kernel module table entry.
Jan 13 11:58:27 albundy kernel: Linux version 2.2.0-pre5 (root@albundy) (gcc version
2.7.2.3) #1 Thu Jan 7 21:11:50 CET 1999
Jan 13 11:58:27 albundy kernel: Detected 400916962 Hz processor.
Jan 13 11:58:27 albundy kernel: Console: colour VGA+ 80x25
Jan 13 11:58:27 albundy kernel: Calibrating delay loop... 799.54 BogoMIPS
Jan 13 11:58:27 albundy kernel: Memory: 257460k/262080k available (860k kernel code,
412k reserved, 3292k data, 56k init)
Jan 13 11:58:27 albundy kernel: CPU: AMD AMD-K6(tm) 3D processor stepping 0c
Jan 13 11:58:27 albundy kernel: Checking 386/387 coupling... OK, FPU using exception
16 error reporting.
Jan 13 11:58:27 albundy kernel: Checking 'hlt' instruction... OK.
Jan 13 11:58:27 albundy kernel: POSIX conformance testing by UNIFIX
Jan 13 11:58:27 albundy kernel: PCI: PCI BIOS revision 2.10 entry at 0xfb490
Jan 13 11:58:27 albundy kernel: PCI: Using configuration type 1
Jan 13 11:58:27 albundy kernel: PCI: Probing PCI hardware
Jan 13 11:58:27 albundy kernel: PCI: 00:38 [1106/0586]: Work around ISA DMA hangs (00)
Jan 13 11:58:27 albundy kernel: Activating ISA DMA hang workarounds.
Jan 13 11:58:27 albundy kernel: Linux NET4.0 for Linux 2.2
Jan 13 11:58:27 albundy kernel: Based upon Swansea University Computer Society NET3.039
Jan 13 11:58:27 albundy kernel: NET4: Unix domain sockets 1.0 for Linux NET4.0.
Jan 13 11:58:27 albundy kernel: NET4: Linux TCP/IP 1.0 for NET4.0
Jan 13 11:58:27 albundy kernel: IP Protocols: ICMP, UDP, TCP
Jan 13 11:58:27 albundy kernel: Starting kswapd v 1.5
Jan 13 11:58:27 albundy kernel: Serial driver version 4.27 with no serial options
enabled
Jan 13 11:58:27 albundy kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A
Jan 13 11:58:27 albundy kernel: ttyS01 at 0x02f8 (irq = 3) is a 16550A
Jan 13 11:58:27 albundy kernel: pty: 256 Unix98 ptys configured
Jan 13 11:58:27 albundy kernel: Floppy drive(s): fd0 is 1.44M
Jan 13 11:58:27 albundy kernel: FDC 0 is a post-1991 82077
Jan 13 11:58:27 albundy kernel: ncr53c8xx: at PCI bus 0, device 10, function 0
Jan 13 11:58:27 albundy kernel: ncr53c8xx: 53c825 detected
Jan 13 11:58:27 albundy kernel: ncr53c825-0: rev=0x02, base=0xec000000,
io_port=0xe000, irq=5
Jan 13 11:58:27 albundy kernel: ncr53c825-0: ID 7, Fast-10, Parity Checking
Jan 13 11:58:27 albundy kernel: ncr53c825-0: restart (scsi reset).
Jan 13 11:58:27 albundy kernel: EATA0: address 0xe010 in use, skipping probe.
Jan 13 11:58:27 albundy kernel: EATA/DMA 2.0x: Copyright (C) 1994-1998 Dario Ballabio.
Jan 13 11:58:27 albundy kernel: EATA config options -> tc:y, lc:y, mq:16, eh:y, rs:y,
et:n.
Jan 13 11:58:27 albundy kernel: EATA0: 2.0C, PCI 0xd810, IRQ 10, BMST, SG 122, MB 64.
Jan 13 11:58:27 albundy kernel: EATA0: wide SCSI support enabled, max_id 16, max_lun 8.
Jan 13 11:58:27 albundy kernel: EATA0: SCSI channel 0 enabled, host target ID 7.
Jan 13 11:58:27 albundy kernel: EATA0: SCSI channel 1 enabled, host target ID 7.
Jan 13 11:58:27 albundy kernel: scsi0 : ncr53c8xx - revision 3.1d
Jan 13 11:58:27 albundy kernel: scsi1 : EATA/DMA 2.0x rev. 4.33.00
Jan 13 11:58:27 albundy kernel: scsi : 2 hosts.
Jan 13 11:58:27 albundy kernel: Vendor: AGFA Model: SNAPSCAN 1236 Rev: 1.40
Jan 13 11:58:27 albundy kernel: Type: Scanner ANSI SCSI
revision: 02
Jan 13 11:58:27 albundy kernel: Vendor: HP Model: C1537A Rev: L610
Jan 13 11:58:27 albundy kernel: Type: Sequential-Access ANSI SCSI
revision: 02
Jan 13 11:58:27 albundy kernel: Vendor: PIONEER Model: CD-ROM DR-U03S Rev: 1.01
Jan 13 11:58:27 albundy kernel: Type: CD-ROM ANSI SCSI
revision: 02
Jan 13 11:58:27 albundy kernel: Vendor: DPT Model: RAID-A Rev: 07L0
Jan 13 11:58:27 albundy kernel: Type: Direct-Access ANSI SCSI
revision: 02
Jan 13 11:58:27 albundy kernel: Detected scsi disk sda at scsi1, channel 0, id 1, lun 0
Jan 13 11:58:27 albundy kernel: Vendor: DPT Model: RAID-B Rev: 07L0
Jan 13 11:58:27 albundy kernel: Type: Direct-Access ANSI SCSI
revision: 02
Jan 13 11:58:27 albundy kernel: Detected scsi disk sdb at scsi1, channel 1, id 0, lun 0
Jan 13 11:58:27 albundy kernel: EATA0: scsi1, channel 0, id 1, lun 0, cmds/lun 16,
sorted, tagged.
Jan 13 11:58:27 albundy kernel: EATA0: scsi1, channel 1, id 0, lun 0, cmds/lun 16,
sorted, tagged.
Jan 13 11:58:27 albundy kernel: scsi : detected 2 SCSI disks total.
Jan 13 11:58:27 albundy kernel: SCSI device sda: hdwr sector= 512 bytes. Sectors=
17915728 [8747 MB] [8.7 GB]
Jan 13 11:58:27 albundy kernel: SCSI device sdb: hdwr sector= 512 bytes. Sectors=
17915728 [8747 MB] [8.7 GB]
Jan 13 11:58:27 albundy kernel: tulip.c:v0.89H 5/23/98 [EMAIL PROTECTED]
Jan 13 11:58:27 albundy kernel: eth0: Digital DS21140 Tulip at 0xdc00, 00 80 c8 94 41
a8, IRQ 11.
Jan 13 11:58:27 albundy kernel: eth0: EEPROM default media type Autosense.
Jan 13 11:58:27 albundy kernel: eth0: Index #0 - Media MII (#11) described by a 21140
MII PHY (1) block.
Jan 13 11:58:27 albundy kernel: eth0: MII transceiver found at MDIO address 0, config
1000 status 782d.
Jan 13 11:58:27 albundy kernel: Partition check:
Jan 13 11:58:27 albundy kernel: sda: sda1 sda2 sda3 sda4
Jan 13 11:58:27 albundy kernel: sdb: sdb1 sdb2 sdb3 sdb4
Jan 13 11:58:27 albundy kernel: VFS: Mounted root (ext2 filesystem) readonly.
Jan 13 11:58:27 albundy kernel: Freeing unused kernel memory: 56k freed
Jan 13 11:58:27 albundy kernel: Adding Swap: 130748k swap-space (priority -1)
Jan 13 11:58:27 albundy kernel: st: bufsize 32768, wrt 30720, max buffers 4, s/g segs
16.
Jan 13 11:58:27 albundy kernel: Detected scsi tape st0 at scsi0, channel 0, id 3, lun 0
Jan 13 11:58:39 albundy mountd[312]: NFS mount of /.cfsfs attempted from 127.0.0.1
Jan 13 11:58:39 albundy mountd[312]: /.cfsfs has been mounted by 127.0.0.1
Jan 13 12:48:22 albundy kernel: ncr53c825-0-<3,*>: FAST-10 SCSI 10.0 MB/s (100 ns,
offset 8)
Jan 13 12:54:10 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=19002913 SSTAT1=6
Jan 13 12:54:10 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 12:54:10 albundy kernel: Additional sense indicates Data phase error
Jan 13 12:54:13 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=190028f5 SSTAT1=6
Jan 13 12:54:13 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 12:54:13 albundy kernel: Additional sense indicates Data phase error
Jan 13 12:54:17 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=19003d14 SSTAT1=6
Jan 13 12:54:17 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 12:54:17 albundy kernel: Additional sense indicates Data phase error
Jan 13 12:54:22 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=19001856 SSTAT1=6
Jan 13 12:54:22 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 12:54:22 albundy kernel: Additional sense indicates Data phase error
Jan 13 12:54:26 albundy kernel: ncr53c825-0:3: ERROR (0:14) (0-a7-80) (8/13) @ (script
3c4:50000000).
Jan 13 12:54:26 albundy kernel: ncr53c825-0: script cmd = 80000000
Jan 13 12:54:26 albundy kernel: ncr53c825-0: regdump: da 10 80 13 47 08 03 0f 35 00 83
a7 80 00 07 02.
Jan 13 12:54:26 albundy kernel: ncr53c825-0: have to clear fifos.
Jan 13 12:54:26 albundy kernel: ncr53c825-0: unexpected disconnect
Jan 13 12:54:27 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=19000114 SSTAT1=6
Jan 13 12:54:27 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 12:54:27 albundy kernel: Additional sense indicates Data phase error
Jan 13 12:54:30 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=19004835 SSTAT1=6
Jan 13 12:54:30 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
... < cut > ...
Jan 13 12:57:38 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 12:57:38 albundy kernel: Additional sense indicates Data phase error
Jan 13 12:57:45 albundy kernel: ncr53c825-0:3: ERROR (0:14) (0-a7-80) (8/13) @ (script
3c4:50000000).
Jan 13 12:57:45 albundy kernel: ncr53c825-0: script cmd = 80000000
Jan 13 12:57:45 albundy kernel: ncr53c825-0: regdump: da 10 80 13 47 08 03 0f 35 00 83
a7 80 00 07 02.
Jan 13 12:57:45 albundy kernel: ncr53c825-0: have to clear fifos.
Jan 13 12:57:45 albundy kernel: ncr53c825-0: unexpected disconnect
Jan 13 12:57:45 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=190009d6 SSTAT1=6
Jan 13 12:57:45 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 12:57:45 albundy kernel: Additional sense indicates Data phase error
Jan 13 12:57:48 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=190041b5 SSTAT1=6
Jan 13 12:57:48 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
... < cut > ...
Jan 13 13:14:57 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=19000eb5 SSTAT1=6
Jan 13 13:14:57 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 13:14:57 albundy kernel: Additional sense indicates Data phase error
Jan 13 13:15:02 albundy kernel: ncr53c825-0:3: ERROR (0:14) (0-a7-80) (8/13) @ (script
3c4:50000000).
Jan 13 13:15:02 albundy kernel: ncr53c825-0: script cmd = 80000000
Jan 13 13:15:02 albundy kernel: ncr53c825-0: regdump: da 10 80 13 47 08 03 0f 35 00 83
a7 80 00 07 02.
Jan 13 13:15:02 albundy kernel: ncr53c825-0: have to clear fifos.
Jan 13 13:15:02 albundy kernel: ncr53c825-0: unexpected disconnect
Jan 13 13:15:02 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=19004bd5 SSTAT1=6
Jan 13 13:15:02 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 13:15:02 albundy kernel: Additional sense indicates Data phase error
Jan 13 13:15:06 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=19003935 SSTAT1=6
Jan 13 13:15:06 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
....< Cut> ....
Jan 13 14:04:20 albundy kernel: scsi : aborting command due to timeout : pid 80254,
scsi0, channel 0, id 3, lun 0 Read (6) 00 00 50 00 00
Jan 13 14:04:20 albundy kernel: ncr53c8xx_abort: pid=80254 serial_number=80267
serial_number_at_timeout=80267
Jan 13 14:04:22 albundy kernel: SCSI host 0 abort (pid 80254) timed out - resetting
Jan 13 14:04:22 albundy kernel: SCSI bus is being reset for host 0 channel 0.
Jan 13 14:04:22 albundy kernel: ncr53c8xx_reset: pid=80254 reset_flags=2
serial_number=80267 serial_number_at_timeout=80267
Jan 13 14:04:22 albundy kernel: ncr53c825-0: restart (scsi reset).
Jan 13 14:04:22 albundy kernel: ncr53c825-0-<3,*>: FAST-10 SCSI 10.0 MB/s (100 ns,
offset 8)
Jan 13 14:04:22 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Unit Attention
Jan 13 14:04:22 albundy kernel: Additional sense indicates Power on, reset, or bus
device reset occurred
Jan 13 14:04:37 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=19004ad6 SSTAT1=6
Jan 13 14:04:37 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 14:04:37 albundy kernel: Additional sense indicates Data phase error
Jan 13 14:04:40 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=190008b6 SSTAT1=6
Jan 13 14:04:40 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 14:04:40 albundy kernel: Additional sense indicates Data phase error
.... < cut > ....
Jan 13 14:06:14 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=19002216 SSTAT1=6
Jan 13 14:06:14 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 14:06:14 albundy kernel: Additional sense indicates Data phase error
Jan 13 14:06:17 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=19001015 SSTAT1=6
Jan 13 14:06:17 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 14:06:17 albundy kernel: Additional sense indicates Data phase error
Jan 13 14:06:20 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=19000e76 SSTAT1=6
Jan 13 14:06:20 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 14:06:20 albundy kernel: Additional sense indicates Data phase error
Jan 13 14:06:24 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=3
DBC=19000bb6 SSTAT1=6
Jan 13 14:06:24 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Aborted Command
Jan 13 14:06:24 albundy kernel: Additional sense indicates Data phase error
Jan 13 14:21:29 albundy kernel: scsi : aborting command due to timeout : pid 82918,
scsi0, channel 0, id 3, lun 0 Read (6) 00 00 50 00 00
Jan 13 14:21:29 albundy kernel: ncr53c8xx_abort: pid=82918 serial_number=82932
serial_number_at_timeout=82932
Jan 13 14:21:29 albundy kernel: ncr53c825-0: abort ccb=ccc5b820 (cancel)
Jan 13 14:21:31 albundy kernel: SCSI host 0 abort (pid 82918) timed out - resetting
Jan 13 14:21:31 albundy kernel: SCSI bus is being reset for host 0 channel 0.
Jan 13 14:21:31 albundy kernel: ncr53c8xx_reset: pid=82918 reset_flags=2
serial_number=82932 serial_number_at_timeout=82932
Jan 13 14:21:31 albundy kernel: ncr53c825-0: restart (scsi reset).
Jan 13 14:21:31 albundy kernel: ncr53c825-0-<3,*>: FAST-10 SCSI 10.0 MB/s (100 ns,
offset 8)
Jan 13 14:21:31 albundy kernel: st0: Error with sense data: extra data not valid
Current error st09:00: sense key Unit Attention
Jan 13 14:21:31 albundy kernel: Additional sense indicates Power on, reset, or bus
device reset occurred
Jan 13 14:25:28 albundy kernel: Detected scsi generic sga at scsi0, channel 0, id 2,
lun 0
Jan 13 14:27:47 albundy kernel: ncr53c825-0:3: ERROR (0:4) (8-0-0) (8/13) @ (script
414:9f030000).
Jan 13 14:27:47 albundy kernel: ncr53c825-0: script cmd = 72580000
Jan 13 14:27:47 albundy kernel: ncr53c825-0: regdump: da 00 80 13 47 08 03 0f 83 08 83
00 80 00 07 02.
Jan 13 14:27:47 albundy kernel: ncr53c825-0: have to clear fifos.
Jan 13 14:27:47 albundy kernel: ncr53c825-0: unexpected disconnect
Jan 13 14:27:47 albundy kernel: ncr53c825-0: SCSI parity error detected: SCR1=138
DBC=9f030000 SSTAT1=7
Jan 13 14:27:47 albundy kernel: ncr53c825-0-<4,*>: FAST-10 SCSI 10.0 MB/s (100 ns,
offset 8)
Jan 13 14:28:48 albundy kernel: ncr53c825-0-<2,*>: SYNC transfers not supported.
Jan 13 14:31:25 albundy kernel: Detected scsi CD-ROM sr0 at scsi0, channel 0, id 4,
lun 0
Jan 13 14:31:25 albundy kernel: sr0: scsi3-mmc drive: 20x/20x xa/form2 cdda tray
Jan 13 14:31:25 albundy kernel: Uniform CDROM driver Revision: 2.51
Jan 13 14:31:38 albundy kernel: Detected scsi generic sga at scsi0, channel 0, id 2,
lun 0
Jan 13 14:36:35 albundy kernel: scsi : aborting command due to timeout : pid 82973,
scsi0, channel 0, id 3, lun 0 Read (6) 00 00 50 00 00
Jan 13 14:36:35 albundy kernel: ncr53c8xx_abort: pid=82973 serial_number=82988
serial_number_at_timeout=82988
Jan 13 14:36:36 albundy kernel: SCSI host 0 abort (pid 82973) timed out - resetting
Jan 13 14:36:36 albundy kernel: SCSI bus is being reset for host 0 channel 0.
Jan 13 14:36:36 albundy kernel: ncr53c8xx_reset: pid=82973 reset_flags=2
serial_number=82988 serial_number_at_timeout=82988
Jan 13 14:36:36 albundy kernel: ncr53c825-0: restart (scsi reset).
Jan 13 14:36:36 albundy kernel: ncr53c825-0-<3,*>: FAST-10 SCSI 10.0 MB/s (100 ns,
offset 8)
Jan 13 15:15:39 albundy syslogd 1.3-3: restart (remote reception).
Jan 13 15:15:39 albundy kernel: klogd 1.3-3, log source = /proc/kmsg started.
Jan 13 15:15:39 albundy kernel: Cannot find map file.
Jan 13 15:15:39 albundy kernel: Error seeking in /dev/kmem
Jan 13 15:15:39 albundy kernel: Error adding kernel module table entry.
Jan 13 15:15:39 albundy kernel: Linux version 2.2.0-pre5 (root@albundy) (gcc version
2.7.2.3) #1 Thu Jan 7 21:11:50 CET 1999
Jan 13 15:15:39 albundy kernel: Detected 400915540 Hz processor.
Jan 13 15:15:39 albundy kernel: Console: colour VGA+ 80x25
Jan 13 15:15:39 albundy kernel: Calibrating delay loop... 799.54 BogoMIPS
Jan 13 15:15:39 albundy kernel: Memory: 257460k/262080k available (860k kernel code,
412k reserved, 3292k data, 56k init)
Jan 13 15:15:39 albundy kernel: CPU: AMD AMD-K6(tm) 3D processor stepping 0c
Jan 13 15:15:39 albundy kernel: Checking 386/387 coupling... OK, FPU using exception
16 error reporting.
Jan 13 15:15:39 albundy kernel: Checking 'hlt' instruction... OK.
Jan 13 15:15:39 albundy kernel: POSIX conformance testing by UNIFIX
Jan 13 15:15:39 albundy kernel: PCI: PCI BIOS revision 2.10 entry at 0xfb490
Jan 13 15:15:39 albundy kernel: PCI: Using configuration type 1
Jan 13 15:15:39 albundy kernel: PCI: Probing PCI hardware
Jan 13 15:15:39 albundy kernel: PCI: 00:38 [1106/0586]: Work around ISA DMA hangs (00)
Jan 13 15:15:39 albundy kernel: Activating ISA DMA hang workarounds.
Jan 13 15:15:39 albundy kernel: Linux NET4.0 for Linux 2.2
Jan 13 15:15:39 albundy kernel: Based upon Swansea University Computer Society NET3.039
Jan 13 15:15:39 albundy kernel: NET4: Unix domain sockets 1.0 for Linux NET4.0.
Jan 13 15:15:39 albundy kernel: NET4: Linux TCP/IP 1.0 for NET4.0
Jan 13 15:15:39 albundy kernel: IP Protocols: ICMP, UDP, TCP
Jan 13 15:15:39 albundy kernel: Starting kswapd v 1.5
Jan 13 15:15:39 albundy kernel: Serial driver version 4.27 with no serial options
enabled
Jan 13 15:15:39 albundy kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A
Jan 13 15:15:39 albundy kernel: ttyS01 at 0x02f8 (irq = 3) is a 16550A
Jan 13 15:15:39 albundy kernel: pty: 256 Unix98 ptys configured
Jan 13 15:15:39 albundy kernel: Floppy drive(s): fd0 is 1.44M
Jan 13 15:15:39 albundy kernel: FDC 0 is a post-1991 82077
Jan 13 15:15:39 albundy kernel: ncr53c8xx: at PCI bus 0, device 10, function 0
Jan 13 15:15:39 albundy kernel: ncr53c8xx: 53c825 detected
Jan 13 15:15:39 albundy kernel: ncr53c825-0: rev=0x02, base=0xec000000,
io_port=0xe000, irq=5
Jan 13 15:15:39 albundy kernel: ncr53c825-0: ID 7, Fast-10, Parity Checking
Jan 13 15:15:39 albundy kernel: ncr53c825-0: restart (scsi reset).
Jan 13 15:15:39 albundy kernel: EATA0: address 0xe010 in use, skipping probe.
Jan 13 15:15:39 albundy kernel: EATA/DMA 2.0x: Copyright (C) 1994-1998 Dario Ballabio.
Jan 13 15:15:39 albundy kernel: EATA config options -> tc:y, lc:y, mq:16, eh:y, rs:y,
et:n.
Jan 13 15:15:39 albundy kernel: EATA0: 2.0C, PCI 0xd810, IRQ 10, BMST, SG 122, MB 64.
Jan 13 15:15:39 albundy kernel: EATA0: wide SCSI support enabled, max_id 16, max_lun 8.
Jan 13 15:15:39 albundy kernel: EATA0: SCSI channel 0 enabled, host target ID 7.
Jan 13 15:15:39 albundy kernel: EATA0: SCSI channel 1 enabled, host target ID 7.
Jan 13 15:15:39 albundy kernel: scsi0 : ncr53c8xx - revision 3.1d
Jan 13 15:15:39 albundy kernel: scsi1 : EATA/DMA 2.0x rev. 4.33.00
Jan 13 15:15:39 albundy kernel: scsi : 2 hosts.
Jan 13 15:15:39 albundy kernel: Vendor: AGFA Model: SNAPSCAN 1236 Rev: 1.40
Jan 13 15:15:39 albundy kernel: Type: Scanner ANSI SCSI
revision: 02
Jan 13 15:15:39 albundy kernel: Vendor: HP Model: C1537A Rev: L610
Jan 13 15:15:39 albundy kernel: Type: Sequential-Access ANSI SCSI
revision: 02
Jan 13 15:15:39 albundy kernel: Vendor: PIONEER Model: CD-ROM DR-U03S Rev: 1.01
Jan 13 15:15:39 albundy kernel: Type: CD-ROM ANSI SCSI
revision: 02
Jan 13 15:15:39 albundy kernel: Vendor: DPT Model: RAID-A Rev: 07L0
Jan 13 15:15:39 albundy kernel: Type: Direct-Access ANSI SCSI
revision: 02
Jan 13 15:15:39 albundy kernel: Detected scsi disk sda at scsi1, channel 0, id 1, lun 0
Jan 13 15:15:39 albundy kernel: Vendor: DPT Model: RAID-B Rev: 07L0
Jan 13 15:15:39 albundy kernel: Type: Direct-Access ANSI SCSI
revision: 02
Jan 13 15:15:39 albundy kernel: Detected scsi disk sdb at scsi1, channel 1, id 0, lun 0
Jan 13 15:15:39 albundy kernel: EATA0: scsi1, channel 0, id 1, lun 0, cmds/lun 16,
sorted, tagged.
Jan 13 15:15:39 albundy kernel: EATA0: scsi1, channel 1, id 0, lun 0, cmds/lun 16,
sorted, tagged.
Jan 13 15:15:39 albundy kernel: scsi : detected 2 SCSI disks total.
Jan 13 15:15:39 albundy kernel: SCSI device sda: hdwr sector= 512 bytes. Sectors=
17915728 [8747 MB] [8.7 GB]
Jan 13 15:15:39 albundy kernel: SCSI device sdb: hdwr sector= 512 bytes. Sectors=
17915728 [8747 MB] [8.7 GB]
Jan 13 15:15:39 albundy kernel: tulip.c:v0.89H 5/23/98 [EMAIL PROTECTED]
Jan 13 15:15:39 albundy kernel: eth0: Digital DS21140 Tulip at 0xdc00, 00 80 c8 94 41
a8, IRQ 11.
Jan 13 15:15:39 albundy kernel: eth0: EEPROM default media type Autosense.
Jan 13 15:15:39 albundy kernel: eth0: Index #0 - Media MII (#11) described by a 21140
MII PHY (1) block.
Jan 13 15:15:39 albundy kernel: eth0: MII transceiver found at MDIO address 0, config
1000 status 782d.
Jan 13 15:15:39 albundy kernel: Partition check:
Jan 13 15:15:39 albundy kernel: sda: sda1 sda2 sda3 sda4
Jan 13 15:15:39 albundy kernel: sdb: sdb1 sdb2 sdb3 sdb4
Jan 13 15:15:39 albundy kernel: VFS: Mounted root (ext2 filesystem) readonly.
Jan 13 15:15:39 albundy kernel: Freeing unused kernel memory: 56k freed
Jan 13 15:15:39 albundy kernel: Adding Swap: 130748k swap-space (priority -1)
Jan 13 15:15:39 albundy kernel: st: bufsize 32768, wrt 30720, max buffers 4, s/g segs
16.
Jan 13 15:15:39 albundy kernel: Detected scsi tape st0 at scsi0, channel 0, id 3, lun 0
Jan 13 15:15:56 albundy mountd[314]: NFS mount of /.cfsfs attempted from 127.0.0.1
Jan 13 15:15:56 albundy mountd[314]: /.cfsfs has been mounted by 127.0.0.1
Jan 13 15:36:58 albundy init: Switching to runlevel: 6
Jan 13 15:37:01 albundy syslogd: exiting on signal 15
Jan 13 15:39:17 albundy syslogd 1.3-3: restart (remote reception).
Jan 13 15:39:17 albundy kernel: klogd 1.3-3, log source = /proc/kmsg started.
Jan 13 15:39:17 albundy kernel: Cannot find map file.
Jan 13 15:39:17 albundy kernel: Error seeking in /dev/kmem
Jan 13 15:39:17 albundy kernel: Error adding kernel module table entry.
Jan 13 15:39:17 albundy kernel: Linux version 2.2.0-pre5 (root@albundy) (gcc version
2.7.2.3) #1 Thu Jan 7 21:11:50 CET 1999
Jan 13 15:39:17 albundy kernel: Detected 400919844 Hz processor.
Jan 13 15:39:17 albundy kernel: Console: colour VGA+ 80x25
Jan 13 15:39:17 albundy kernel: Calibrating delay loop... 799.54 BogoMIPS
Jan 13 15:39:17 albundy kernel: Memory: 257460k/262080k available (860k kernel code,
412k reserved, 3292k data, 56k init)
Jan 13 15:39:17 albundy kernel: CPU: AMD AMD-K6(tm) 3D processor stepping 0c
Jan 13 15:39:17 albundy kernel: Checking 386/387 coupling... OK, FPU using exception
16 error reporting.
Jan 13 15:39:17 albundy kernel: Checking 'hlt' instruction... OK.
Jan 13 15:39:17 albundy kernel: POSIX conformance testing by UNIFIX
Jan 13 15:39:17 albundy kernel: PCI: PCI BIOS revision 2.10 entry at 0xfb490
Jan 13 15:39:17 albundy kernel: PCI: Using configuration type 1
Jan 13 15:39:17 albundy kernel: PCI: Probing PCI hardware
Jan 13 15:39:17 albundy kernel: PCI: 00:38 [1106/0586]: Work around ISA DMA hangs (00)
Jan 13 15:39:17 albundy kernel: Activating ISA DMA hang workarounds.
Jan 13 15:39:17 albundy kernel: Linux NET4.0 for Linux 2.2
Jan 13 15:39:17 albundy kernel: Based upon Swansea University Computer Society NET3.039
Jan 13 15:39:17 albundy kernel: NET4: Unix domain sockets 1.0 for Linux NET4.0.
Jan 13 15:39:17 albundy kernel: NET4: Linux TCP/IP 1.0 for NET4.0
Jan 13 15:39:17 albundy kernel: IP Protocols: ICMP, UDP, TCP
Jan 13 15:39:17 albundy kernel: Starting kswapd v 1.5
Jan 13 15:39:17 albundy kernel: Serial driver version 4.27 with no serial options
enabled
Jan 13 15:39:17 albundy kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A
Jan 13 15:39:17 albundy kernel: ttyS01 at 0x02f8 (irq = 3) is a 16550A
Jan 13 15:39:17 albundy kernel: pty: 256 Unix98 ptys configured
Jan 13 15:39:17 albundy kernel: Floppy drive(s): fd0 is 1.44M
Jan 13 15:39:17 albundy kernel: FDC 0 is a post-1991 82077
Jan 13 15:39:17 albundy kernel: ncr53c8xx: at PCI bus 0, device 10, function 0
Jan 13 15:39:17 albundy kernel: ncr53c8xx: 53c825 detected
Jan 13 15:39:17 albundy kernel: ncr53c825-0: rev=0x02, base=0xec000000,
io_port=0xe000, irq=5
Jan 13 15:39:17 albundy kernel: ncr53c825-0: ID 7, Fast-10, Parity Checking
Jan 13 15:39:17 albundy kernel: ncr53c825-0: restart (scsi reset).
Jan 13 15:39:17 albundy kernel: EATA0: address 0xe010 in use, skipping probe.
Jan 13 15:39:17 albundy kernel: EATA/DMA 2.0x: Copyright (C) 1994-1998 Dario Ballabio.
Jan 13 15:39:17 albundy kernel: EATA config options -> tc:y, lc:y, mq:16, eh:y, rs:y,
et:n.
Jan 13 15:39:17 albundy kernel: EATA0: 2.0C, PCI 0xd810, IRQ 10, BMST, SG 122, MB 64.
Jan 13 15:39:17 albundy kernel: EATA0: wide SCSI support enabled, max_id 16, max_lun 8.
Jan 13 15:39:17 albundy kernel: EATA0: SCSI channel 0 enabled, host target ID 7.
Jan 13 15:39:17 albundy kernel: EATA0: SCSI channel 1 enabled, host target ID 7.
Jan 13 15:39:17 albundy kernel: scsi0 : ncr53c8xx - revision 3.1d
Jan 13 15:39:17 albundy kernel: scsi1 : EATA/DMA 2.0x rev. 4.33.00
Jan 13 15:39:17 albundy kernel: scsi : 2 hosts.
Jan 13 15:39:17 albundy kernel: Vendor: AGFA Model: SNAPSCAN 1236 Rev: 1.40
Jan 13 15:39:17 albundy kernel: Type: Scanner ANSI SCSI
revision: 02
Jan 13 15:39:17 albundy kernel: Vendor: HP Model: C1537A Rev: L610
Jan 13 15:39:17 albundy kernel: Type: Sequential-Access ANSI SCSI
revision: 02
Jan 13 15:39:17 albundy kernel: Vendor: PIONEER Model: CD-ROM DR-U03S Rev: 1.01
Jan 13 15:39:17 albundy kernel: Type: CD-ROM ANSI SCSI
revision: 02
Jan 13 15:39:17 albundy kernel: Vendor: DPT Model: RAID-A Rev: 07L0
Jan 13 15:39:17 albundy kernel: Type: Direct-Access ANSI SCSI
revision: 02
Jan 13 15:39:17 albundy kernel: Detected scsi disk sda at scsi1, channel 0, id 1, lun 0
Jan 13 15:39:17 albundy kernel: Vendor: DPT Model: RAID-B Rev: 07L0
Jan 13 15:39:17 albundy kernel: Type: Direct-Access ANSI SCSI
revision: 02
Jan 13 15:39:17 albundy kernel: Detected scsi disk sdb at scsi1, channel 1, id 0, lun 0
Jan 13 15:39:17 albundy kernel: EATA0: scsi1, channel 0, id 1, lun 0, cmds/lun 16,
sorted, tagged.
Jan 13 15:39:17 albundy kernel: EATA0: scsi1, channel 1, id 0, lun 0, cmds/lun 16,
sorted, tagged.
Jan 13 15:39:17 albundy kernel: scsi : detected 2 SCSI disks total.
Jan 13 15:39:17 albundy kernel: SCSI device sda: hdwr sector= 512 bytes. Sectors=
17915728 [8747 MB] [8.7 GB]
Jan 13 15:39:17 albundy kernel: SCSI device sdb: hdwr sector= 512 bytes. Sectors=
17915728 [8747 MB] [8.7 GB]
Jan 13 15:39:17 albundy kernel: tulip.c:v0.89H 5/23/98 [EMAIL PROTECTED]
Jan 13 15:39:17 albundy kernel: eth0: Digital DS21140 Tulip at 0xdc00, 00 80 c8 94 41
a8, IRQ 11.
Jan 13 15:39:17 albundy kernel: eth0: EEPROM default media type Autosense.
Jan 13 15:39:17 albundy kernel: eth0: Index #0 - Media MII (#11) described by a 21140
MII PHY (1) block.
Jan 13 15:39:17 albundy kernel: eth0: MII transceiver found at MDIO address 0, config
1000 status 782d.
Jan 13 15:39:17 albundy kernel: Partition check:
Jan 13 15:39:17 albundy kernel: sda: sda1 sda2 sda3 sda4
Jan 13 15:39:17 albundy kernel: sdb: sdb1 sdb2 sdb3 sdb4
Jan 13 15:39:17 albundy kernel: VFS: Mounted root (ext2 filesystem) readonly.
Jan 13 15:39:17 albundy kernel: Freeing unused kernel memory: 56k freed
Jan 13 15:39:17 albundy kernel: Adding Swap: 130748k swap-space (priority -1)
Jan 13 15:39:17 albundy kernel: st: bufsize 32768, wrt 30720, max buffers 4, s/g segs
16.
Jan 13 15:39:17 albundy kernel: Detected scsi tape st0 at scsi0, channel 0, id 3, lun 0
Jan 13 15:39:29 albundy mountd[312]: NFS mount of /.cfsfs attempted from 127.0.0.1
Jan 13 15:39:29 albundy mountd[312]: /.cfsfs has been mounted by 127.0.0.1
Jan 13 15:48:17 albundy syslogd: recvfrom unix
Jan 13 15:52:42 albundy kernel: Unable to handle kernel paging request at virtual
address ef32413c
Jan 13 15:52:42 albundy kernel: current->tss.cr3 = 00101000, pr3 = 00101000
Jan 13 15:52:42 albundy kernel: *pde = 00000000
Jan 13 15:52:42 albundy kernel: Oops: 0000
Jan 13 15:52:42 albundy kernel: CPU: 0
Jan 13 15:52:42 albundy kernel: EIP: 0010:[<c0174a6f>]
Jan 13 15:52:42 albundy kernel: EFLAGS: 00010206
Jan 13 15:52:42 albundy kernel: eax: cf324104 ebx: 00000000 ecx: ef324104 edx:
ef324104
Jan 13 15:52:42 albundy kernel: esi: cf3240c0 edi: 00000000 ebp: cfda7480 esp:
cdfeff04
Jan 13 15:52:42 albundy kernel: ds: 0018 es: 0018 ss: 0018
Jan 13 15:52:42 albundy kernel: Process wish (pid: 523, process nr: 52,
stackpage=cdfef000)
Jan 13 15:52:42 albundy kernel: Stack: ce7faf00 cfda7480 c0172f3e cf3240c0 ce464dc0
ce464000 ce7faf00 c0172e7e
Jan 13 15:52:42 albundy kernel: ce464000 ce5bf4c8 ce5bf430 c0173108 ce464000
c0154667 ce5bf4c8 00000000
Jan 13 15:52:42 albundy kernel: ce5bf430 c0154a61 ce5bf4c8 ce1a5540 c0121463
ce5bf430 ce1a5540 ce1a5540
Jan 13 15:52:42 albundy kernel: Call Trace: [<c0172f3e>] [<c0172e7e>] [<c0173108>]
[<c0154667>] [<c0154a61>] [<c0121463>] [<c0122540>]
Jan 13 15:52:42 albundy kernel: [<c01214e6>] [<c0114b58>] [<c0114c6e>]
[<c0107a20>]
Jan 13 15:52:42 albundy kernel: Code: 8b 41 38 85 c0 0f 84 a3 00 00 00 8d 68 04 8b 00
48 89 44 24
Jan 13 15:52:50 albundy kernel: EXT2-fs warning (device 08:11): ext2_free_blocks: bit
already cleared for block 2139309
Jan 13 15:52:50 albundy kernel: EXT2-fs warning (device 08:11): ext2_free_blocks: bit
already cleared for block 2139567
Jan 13 15:52:50 albundy kernel: EXT2-fs warning (device 08:11): ext2_free_blocks: bit
already cleared for block 2139824
Jan 13 15:59:04 albundy kernel: Detected scsi generic sga at scsi0, channel 0, id 2,
lun 0
Jan 13 15:59:04 albundy kernel: ncr53c825-0-<4,*>: FAST-10 SCSI 10.0 MB/s (100 ns,
offset 8)
Jan 13 15:59:04 albundy kernel: ncr53c825-0-<2,*>: SYNC transfers not supported.
Jan 13 15:59:04 albundy kernel: ncr53c825-0-<3,*>: FAST-10 SCSI 10.0 MB/s (100 ns,
offset 8)
Jan 13 16:03:02 albundy kernel: ncr53c825-0-<2,0>: extraneous data discarded.
Jan 13 16:03:02 albundy kernel: ncr53c825-0-<2,0>: COMMAND FAILED (89 0) @c009a820.
Jan 13 16:03:16 albundy modprobe: can't locate module block-major-3
Jan 13 16:03:16 albundy last message repeated 7 times
Jan 13 16:08:13 albundy init: Switching to runlevel: 6
Jan 13 16:08:14 albundy kernel: Unable to handle kernel paging request at virtual
address 80000000
Jan 13 16:08:14 albundy kernel: current->tss.cr3 = 0f7e9000, pr3 = 0f7e9000
Jan 13 16:08:14 albundy kernel: *pde = 00000000
Jan 13 16:08:14 albundy kernel: Oops: 0000
Jan 13 16:08:14 albundy kernel: CPU: 0
Jan 13 16:08:14 albundy kernel: EIP: 0010:[<c0170f04>]
Jan 13 16:08:14 albundy kernel: EFLAGS: 00010286
Jan 13 16:08:14 albundy kernel: eax: cea054e4 ebx: 80000000 ecx: cf324c50 edx:
00000001
Jan 13 16:08:14 albundy kernel: esi: cf324bc0 edi: cfd85aa0 ebp: c0528140 esp:
ceb6bf38
Jan 13 16:08:14 albundy kernel: ds: 0018 es: 0018 ss: 0018
Jan 13 16:08:14 albundy kernel: Process X (pid: 394, process nr: 41,
stackpage=ceb6b000)
Jan 13 16:08:14 albundy kernel: Stack: c016fe5b cf324bc0 cf324bc0 cea054c8 cea05430
c0154667 cea054c8 00000000
Jan 13 16:08:14 albundy kernel: cea05430 c0154a61 cea054c8 ceaf04a0 c0121463
cea05430 ceaf04a0 ceaf04a0
Jan 13 16:08:14 albundy kernel: 00000000 cfd85aa0 c0122540 ceaf04a0 ceaf04a0
ceaf04a0 c01214e6 ceaf04a0
Jan 13 16:08:14 albundy kernel: Call Trace: [<c016fe5b>] [<c0154667>] [<c0154a61>]
[<c0121463>] [<c0122540>] [<c01214e6>] [<c012153c>]
Jan 13 16:08:14 albundy kernel: [<c0107a20>]
Jan 13 16:08:14 albundy kernel: Code: 8b 03 89 86 5c 02 00 00 8b 43 10 50 e8 67 dd ff
ff 89 c2 83
Jan 13 16:08:20 albundy kernel: Unable to handle kernel paging request at virtual
address ef324104
Jan 13 16:08:20 albundy kernel: current->tss.cr3 = 00101000, pr3 = 00101000
Jan 13 16:08:20 albundy kernel: *pde = 00000000
Jan 13 16:08:20 albundy kernel: Oops: 0000
Jan 13 16:08:20 albundy kernel: CPU: 0
Jan 13 16:08:20 albundy kernel: EIP: 0010:[<c0172ea9>]
Jan 13 16:08:20 albundy kernel: EFLAGS: 00010006
Jan 13 16:08:20 albundy kernel: eax: ef324104 ebx: ef324104 ecx: 00000000 edx:
00000286
Jan 13 16:08:20 albundy kernel: esi: cf324104 edi: cf3240c0 ebp: c0528920 esp:
cf31ff1c
Jan 13 16:08:20 albundy kernel: ds: 0018 es: 0018 ss: 0018
Jan 13 16:08:20 albundy kernel: Process rpc.mountd (pid: 312, process nr: 19,
stackpage=cf31f000)
Jan 13 16:08:20 albundy kernel: Stack: cfd3cf00 c0172e79 cf3240c0 cf374f40 cf374ea8
c0173108 cf3240c0 c0154667
Jan 13 16:08:20 albundy kernel: cf374f40 00000000 cf374ea8 c0154a61 cf374f40
cf761720 c0121463 cf374ea8
Jan 13 16:10:28 albundy syslogd 1.3-3: restart (remote reception).
Jan 13 16:10:28 albundy kernel: klogd 1.3-3, log source = /proc/kmsg started.
Jan 13 16:10:28 albundy kernel: Cannot find map file.
Jan 13 16:10:28 albundy kernel: Error seeking in /dev/kmem
Jan 13 16:10:28 albundy kernel: Error adding kernel module table entry.
Jan 13 16:10:28 albundy kernel: Linux version 2.2.0-pre5 (root@albundy) (gcc version
2.7.2.3) #1 Wed Jan 13 15:58:31 CET 1999
Jan 13 16:10:28 albundy kernel: Detected 400918422 Hz processor.
Jan 13 16:10:28 albundy kernel: Console: colour VGA+ 80x25
Jan 13 16:10:28 albundy kernel: Calibrating delay loop... 799.54 BogoMIPS
Jan 13 16:10:28 albundy kernel: Memory: 257532k/262080k available (820k kernel code,
408k reserved, 3288k data, 32k init)
Jan 13 16:10:28 albundy kernel: CPU: AMD AMD-K6(tm) 3D processor stepping 0c
Jan 13 16:10:28 albundy kernel: Checking 386/387 coupling... OK, FPU using exception
16 error reporting.
Jan 13 16:10:28 albundy kernel: Checking 'hlt' instruction... OK.
Jan 13 16:10:28 albundy kernel: POSIX conformance testing by UNIFIX
Jan 13 16:10:28 albundy kernel: PCI: PCI BIOS revision 2.10 entry at 0xfb490
Jan 13 16:10:28 albundy kernel: PCI: Using configuration type 1
Jan 13 16:10:28 albundy kernel: PCI: Probing PCI hardware
Jan 13 16:10:28 albundy kernel: PCI: 00:38 [1106/0586]: Work around ISA DMA hangs (00)
Jan 13 16:10:28 albundy kernel: Activating ISA DMA hang workarounds.
Jan 13 16:10:28 albundy kernel: Linux NET4.0 for Linux 2.2
Jan 13 16:10:28 albundy kernel: Based upon Swansea University Computer Society NET3.039
Jan 13 16:10:28 albundy kernel: NET4: Unix domain sockets 1.0 for Linux NET4.0.
Jan 13 16:10:28 albundy kernel: NET4: Linux TCP/IP 1.0 for NET4.0
Jan 13 16:10:28 albundy kernel: IP Protocols: ICMP, UDP, TCP
Jan 13 16:10:28 albundy kernel: Starting kswapd v 1.5
Jan 13 16:10:28 albundy kernel: Serial driver version 4.27 with no serial options
enabled
Jan 13 16:10:28 albundy kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A
Jan 13 16:10:28 albundy kernel: ttyS01 at 0x02f8 (irq = 3) is a 16550A
Jan 13 16:10:28 albundy kernel: pty: 256 Unix98 ptys configured
Jan 13 16:10:28 albundy kernel: Floppy drive(s): fd0 is 1.44M
Jan 13 16:10:28 albundy kernel: FDC 0 is a post-1991 82077
Jan 13 16:10:28 albundy kernel: EATA/DMA 2.0x: Copyright (C) 1994-1998 Dario Ballabio.
Jan 13 16:10:28 albundy kernel: EATA config options -> tc:y, lc:y, mq:16, eh:y, rs:y,
et:n.
Jan 13 16:10:28 albundy kernel: EATA0: 2.0C, PCI 0xd810, IRQ 10, BMST, SG 122, MB 64.
Jan 13 16:10:28 albundy kernel: EATA0: wide SCSI support enabled, max_id 16, max_lun 8.
Jan 13 16:10:28 albundy kernel: EATA0: SCSI channel 0 enabled, host target ID 7.
Jan 13 16:10:28 albundy kernel: EATA0: SCSI channel 1 enabled, host target ID 7.
Jan 13 16:10:28 albundy kernel: scsi0 : EATA/DMA 2.0x rev. 4.33.00
Jan 13 16:10:28 albundy kernel: scsi : 1 host.
Jan 13 16:10:28 albundy kernel: Vendor: DPT Model: RAID-A Rev: 07L0
Jan 13 16:10:28 albundy kernel: Type: Direct-Access ANSI SCSI
revision: 02
Jan 13 16:10:28 albundy kernel: Detected scsi disk sda at scsi0, channel 0, id 1, lun 0
Jan 13 16:10:28 albundy kernel: Vendor: DPT Model: RAID-B Rev: 07L0
Jan 13 16:10:28 albundy kernel: Type: Direct-Access ANSI SCSI
revision: 02
Jan 13 16:10:28 albundy kernel: Detected scsi disk sdb at scsi0, channel 1, id 0, lun 0
Jan 13 16:10:28 albundy kernel: EATA0: scsi0, channel 0, id 1, lun 0, cmds/lun 16,
sorted, tagged.
Jan 13 16:10:28 albundy kernel: EATA0: scsi0, channel 1, id 0, lun 0, cmds/lun 16,
sorted, tagged.
Jan 13 16:10:28 albundy kernel: scsi : detected 2 SCSI disks total.
Jan 13 16:10:28 albundy kernel: SCSI device sda: hdwr sector= 512 bytes. Sectors=
17915728 [8747 MB] [8.7 GB]
Jan 13 16:10:28 albundy kernel: SCSI device sdb: hdwr sector= 512 bytes. Sectors=
17915728 [8747 MB] [8.7 GB]
Jan 13 16:10:28 albundy kernel: tulip.c:v0.89H 5/23/98 [EMAIL PROTECTED]
Jan 13 16:10:28 albundy kernel: eth0: Digital DS21140 Tulip at 0xdc00, 00 80 c8 94 41
a8, IRQ 11.
Jan 13 16:10:28 albundy kernel: eth0: EEPROM default media type Autosense.
Jan 13 16:10:28 albundy kernel: eth0: Index #0 - Media MII (#11) described by a 21140
MII PHY (1) block.
Jan 13 16:10:28 albundy kernel: eth0: MII transceiver found at MDIO address 0, config
1000 status 782d.
Jan 13 16:10:28 albundy kernel: Partition check:
Jan 13 16:10:28 albundy kernel: sda: sda1 sda2 sda3 sda4
Jan 13 16:10:28 albundy kernel: sdb: sdb1 sdb2 sdb3 sdb4
Jan 13 16:10:28 albundy kernel: VFS: Mounted root (ext2 filesystem) readonly.
Jan 13 16:10:28 albundy kernel: Freeing unused kernel memory: 32k freed
Jan 13 16:10:28 albundy kernel: Adding Swap: 130748k swap-space (priority -1)
Jan 13 16:10:28 albundy kernel: EXT2-fs error (device 08:11):
ext2_check_blocks_bitmap: Wrong free blocks count for group 261, stored = 6114,
counted = 5981
Jan 13 16:10:28 albundy kernel: EXT2-fs error (device 08:11):
ext2_check_blocks_bitmap: Wrong free blocks count in super block, stored = 2604660,
counted = 2604527
Jan 13 16:10:29 albundy kernel: parport0: PC-style at 0x378 [SPP,PS2,EPP]
Jan 13 16:10:53 albundy mountd[310]: NFS mount of /.cfsfs attempted from 127.0.0.1
Jan 13 16:10:53 albundy mountd[310]: /.cfsfs has been mounted by 127.0.0.1
Jan 13 16:21:58 albundy kernel: scsi-ncr53c7,8xx : at PCI bus 0, device 10, function 0
Jan 13 16:21:58 albundy kernel: scsi-ncr53c7,8xx : NCR53c825 at memory 0xec000000, io
0xe000, irq 5
Jan 13 16:21:58 albundy kernel: scsi1 : burst length 8
Jan 13 16:21:58 albundy kernel: scsi1 : NCR code relocated to 0xe22c610 (virt
0xce22c610)
Jan 13 16:21:58 albundy kernel: scsi1 : test 1 started
Jan 13 16:21:58 albundy kernel: scsi1 : NCR53c{7,8}xx (rel 17)
Jan 13 16:21:58 albundy kernel: scsi : 2 hosts.
Jan 13 16:22:01 albundy kernel: scsi1 : target 2 rejected SDTR
Jan 13 16:22:01 albundy kernel: scsi1 : setting target 2 to asynchronous SCSI
Jan 13 16:22:01 albundy kernel: Vendor: AGFA Model: SNAPSCAN 1236 Rev: 1.40
Jan 13 16:22:01 albundy kernel: Type: Scanner ANSI SCSI
revision: 02
Jan 13 16:22:01 albundy kernel: scsi1 : target 3 accepting period 100ns offset 8
10.00MHz FAST SCSI-II
Jan 13 16:22:01 albundy kernel: scsi1 : setting target 3 to period 100ns offset 8
10.00MHz FAST SCSI-II
Jan 13 16:22:01 albundy kernel: Vendor: HP Model: C1537A Rev: L610
Jan 13 16:22:01 albundy kernel: Type: Sequential-Access ANSI SCSI
revision: 02
Jan 13 16:22:01 albundy kernel: scsi1 : target 4 accepting period 100ns offset 8
10.00MHz FAST SCSI-II
Jan 13 16:22:01 albundy kernel: scsi1 : setting target 4 to period 100ns offset 8
10.00MHz FAST SCSI-II
Jan 13 16:22:01 albundy kernel: Vendor: PIONEER Model: CD-ROM DR-U03S Rev: 1.01
Jan 13 16:22:01 albundy kernel: Type: CD-ROM ANSI SCSI
revision: 02
Jan 13 16:22:01 albundy kernel: Detected scsi CD-ROM sr0 at scsi1, channel 0, id 4,
lun 0
Jan 13 16:22:03 albundy kernel: sr0: scsi3-mmc drive: 20x/20x xa/form2 cdda tray
Jan 13 16:22:03 albundy kernel: Uniform CDROM driver Revision: 2.51
Jan 13 16:23:16 albundy kernel: st: bufsize 32768, wrt 30720, max buffers 4, s/g segs
16.
Jan 13 16:23:16 albundy kernel: Detected scsi tape st0 at scsi1, channel 0, id 3, lun 0
Jan 13 16:24:26 albundy kernel: st: Unloaded.
Jan 13 16:25:54 albundy kernel: st: bufsize 32768, wrt 30720, max buffers 4, s/g segs
16.
Jan 13 16:25:54 albundy kernel: Detected scsi tape st0 at scsi1, channel 0, id 3, lun 0
Jan 13 16:29:56 albundy kernel: scsi1 : DANGER : abort_connected() called
Jan 13 16:29:56 albundy kernel: st0: Error 27070000 (sugg. bt 0x20, driver bt 0x27,
host bt 0x7).
Jan 13 16:32:12 albundy kernel: scsi1 : SCSI FIFO not empty
Jan 13 16:32:12 albundy kernel: scsi1 : unknown location : unexpected phase DATAIN.
Jan 13 16:32:12 albundy kernel: scsi1 : DCMD|DBC=0x8413cc9, DNAD=0xc0000020 (virt
0xc0000020)
Jan 13 16:32:12 albundy kernel: DSA=0xf80c1d0 (virt 0xcf80c1d0)
Jan 13 16:32:12 albundy kernel: DSPS=0xc0000001, TEMP=0xf80c1d0 (virt
0xcf80c1d0), DMODE=0x88
Jan 13 16:32:12 albundy kernel: SXFER=0x8, SCNTL3=0x13
Jan 13 16:32:12 albundy kernel: BSY phase=DATAIN, 8 bytes in SCSI FIFO
Jan 13 16:32:12 albundy kernel: STEST0=0x5
Jan 13 16:32:12 albundy kernel: scsi1 : DSP 0xf80c1d0 (virt 0xcf80c1d0) ->
Jan 13 16:32:12 albundy kernel: 0xf80c1d0 (virt 0xcf80c1d0) : 0x08413ce8 0xc0000001
(virt 0xc0000001)
Jan 13 16:32:12 albundy kernel: 0xf80c1d8 (virt 0xcf80c1d8) : 0x083ff9d8 0x00000004
(virt 0xc0000004)
Jan 13 16:32:12 albundy kernel: 0xf80c1e0 (virt 0xcf80c1e0) : 0x01dd0210 0x00000026
(virt 0xc0000026)
Jan 13 16:32:12 albundy kernel: 0xf80c1e8 (virt 0xcf80c1e8) : 0x00800091 0x00000000
(virt 0xc0000000)
Jan 13 16:32:12 albundy kernel: 0xf80c1f0 (virt 0xcf80c1f0) : 0x00980055 0x08000000
(virt 0xc8000000)
Jan 13 16:32:12 albundy kernel: 0xf80c1f8 (virt 0xcf80c1f8) : 0xc0000001 0x083ff9d8
(virt 0xc83ff9d8) 0x00000000 (virt 0xc0000000)
Jan 13 16:32:12 albundy kernel: scsi1 : connected (SDID=0x3, SSID=0x83)
Jan 13 16:32:12 albundy kernel: scsi1 : dsa at phys 0xf80c1d0 (virt 0xcf80c1d0)
Jan 13 16:32:12 albundy kernel: + 64 : dsa_msgout length = 1, data = 0xf80c014
(virt 0xcf80c014)
Jan 13 16:32:12 albundy kernel: Identify disconnect allowed lun 0
Jan 13 16:32:12 albundy kernel: + 60 : select_indirect = 0x13030800
Jan 13 16:32:12 albundy kernel: + 56 : dsa_cmnd = 0xfffc00
result = 0xffff, target = 3, lun = 0, cmd = Read (6) 00 00 50 00 00
Jan 13 16:32:12 albundy kernel: + 48 : dsa_next = 0x0
Jan 13 16:32:12 albundy kernel: scsi1 target 3 : sxfer_sanity = 0x8, scntl3_sanity =
0x13
Jan 13 16:32:12 albundy kernel: script : 0x78031300 0x0 0x78050800
0x0 0x90080000 0x0 0x0 0x0
Jan 13 16:32:12 albundy kernel: scsi1 : saved data pointer at offset 0
Jan 13 16:32:12 albundy kernel: scsi1 : can't determine active data pointer offset
Jan 13 16:32:12 albundy kernel: 0xe22c864 (virt 0xce22c864) : 0x820b0000 0x0e22c85c
(virt 0xce22c85c)
Jan 13 16:32:12 albundy kernel: 0xe22c86c (virt 0xce22c86c) : 0x8f0b0000 0x0e22ca14
(virt 0xce22ca14)
Jan 13 16:32:12 albundy kernel: scsi1 : issue queue
Jan 13 16:32:12 albundy kernel: scsi1 : schedule dsa array :
Jan 13 16:32:12 albundy kernel: scsi1 : end schedule dsa array
Jan 13 16:32:12 albundy kernel: scsi1 : reconnect_dsa_head :
Jan 13 16:32:12 albundy kernel: scsi1: bad DSA pointer 0xc0000000scsi1 : end
reconnect_dsa_head
Jan 13 16:32:12 albundy kernel: scsi1 : DANGER : abort_connected() called
Jan 13 16:32:12 albundy kernel: st0: Error 27070000 (sugg. bt 0x20, driver bt 0x27,
host bt 0x7).
Jan 13 16:50:17 albundy kernel: scsi : aborting command due to timeout : pid 37486,
scsi1, channel 0, id 3, lun 0 Read (6) 00 00 50 00 00
Jan 13 16:50:17 albundy kernel: scsi1 : DANGER : command running, can not abort.
... <cut> ...
Jan 13 21:09:59 albundy kernel: klogd 1.3-3, log source = /proc/kmsg started.
Jan 13 21:09:59 albundy kernel: Loaded 3196 symbols from /System.map.
Jan 13 21:09:59 albundy kernel: Symbols match kernel version 2.0.36.
Jan 13 21:09:59 albundy kernel: No module symbols loaded.
Jan 13 21:09:59 albundy kernel: Memory: sized by int13 0e801h
Jan 13 21:09:59 albundy kernel: Console: 16 point font, 400 scans
Jan 13 21:09:59 albundy kernel: Console: colour VGA+ 80x25, 1 virtual console (max 63)
Jan 13 21:09:59 albundy kernel: pcibios_init : BIOS32 Service Directory structure at
0x000fafe0
Jan 13 21:09:59 albundy kernel: pcibios_init : BIOS32 Service Directory entry at
0xfb460
Jan 13 21:09:59 albundy kernel: pcibios_init : PCI BIOS revision 2.10 entry at 0xfb490
Jan 13 21:09:59 albundy kernel: Probing PCI hardware.
Jan 13 21:09:59 albundy kernel: Calibrating delay loop.. ok - 799.54 BogoMIPS
Jan 13 21:09:59 albundy kernel: Memory: 257220k/262080k available (604k kernel code,
384k reserved, 3872k data)
Jan 13 21:09:59 albundy kernel: Swansea University Computer Society NET3.035 for Linux
2.0
Jan 13 21:09:59 albundy kernel: NET3: Unix domain sockets 0.13 for Linux NET3.035.
Jan 13 21:09:59 albundy kernel: Swansea University Computer Society TCP/IP for NET3.034
Jan 13 21:09:59 albundy kernel: IP Protocols: ICMP, UDP, TCP
Jan 13 21:09:59 albundy kernel: VFS: Diskquotas version dquot_5.6.0 initialized
Jan 13 21:09:59 albundy kernel:
Jan 13 21:09:59 albundy kernel: Checking 386/387 coupling... Ok, fpu using exception
16 error reporting.
Jan 13 21:09:59 albundy kernel: Checking 'hlt' instruction... Ok.
Jan 13 21:09:59 albundy kernel: Linux version 2.0.36 (root@albundy) (gcc version
2.7.2.3) #1 Wed Jan 13 21:03:03 CET 1999
Jan 13 21:09:59 albundy kernel: Starting kswapd v 1.4.2.2
Jan 13 21:09:59 albundy kernel: Serial driver version 4.13 with no serial options
enabled
Jan 13 21:09:59 albundy kernel: tty00 at 0x03f8 (irq = 4) is a 16550A
Jan 13 21:09:59 albundy kernel: tty01 at 0x02f8 (irq = 3) is a 16550A
Jan 13 21:09:59 albundy kernel: PS/2 auxiliary pointing device detected -- driver
installed.
Jan 13 21:09:59 albundy kernel: Floppy drive(s): fd0 is 1.44M
Jan 13 21:09:59 albundy kernel: FDC 0 is a post-1991 82077
Jan 13 21:09:59 albundy kernel: EATA (Extended Attachment) driver version: 2.59b
Jan 13 21:09:59 albundy kernel: developed in co-operation with DPT
Jan 13 21:09:59 albundy kernel: (c) 1993-96 Michael Neuffer, [EMAIL PROTECTED]
Jan 13 21:09:59 albundy kernel: Registered HBAs:
Jan 13 21:09:59 albundy kernel: HBA no. Boardtype Revis EATA Bus BaseIO IRQ DMA
Ch ID Pr QS S/G IS
Jan 13 21:09:59 albundy kernel: scsi0 : PM3334UW v07L.0 2.0c PCI 0xd810 10 BMST
2 7 N 64 252 Y
Jan 13 21:09:59 albundy kernel: scsi0 : EATA (Extended Attachment) HBA driver
Jan 13 21:09:59 albundy kernel: scsi : 1 host.
Jan 13 21:09:59 albundy kernel: Vendor: DPT Model: RAID-A Rev: 07L0
Jan 13 21:09:59 albundy kernel: Type: Direct-Access ANSI SCSI
revision: 02
Jan 13 21:09:59 albundy kernel: Detected scsi disk sda at scsi0, channel 0, id 1, lun 0
Jan 13 21:09:59 albundy kernel: Vendor: DPT Model: RAID-B Rev: 07L0
Jan 13 21:09:59 albundy kernel: Type: Direct-Access ANSI SCSI
revision: 02
Jan 13 21:09:59 albundy kernel: Detected scsi disk sdb at scsi0, channel 1, id 0, lun 0
Jan 13 21:09:59 albundy kernel: scsi0: queue depth for target 1 on channel 0 set to 32
Jan 13 21:09:59 albundy kernel: scsi0: queue depth for target 0 on channel 1 set to 32
Jan 13 21:09:59 albundy kernel: scsi : detected 2 SCSI disks total.
Jan 13 21:09:59 albundy kernel: SCSI device sda: hdwr sector= 512 bytes. Sectors=
17915728 [8747 MB] [8.7 GB]
Jan 13 21:09:59 albundy kernel: SCSI device sdb: hdwr sector= 512 bytes. Sectors=
17915728 [8747 MB] [8.7 GB]
Jan 13 21:09:59 albundy kernel: tulip.c:v0.89H 5/23/98 [EMAIL PROTECTED]
Jan 13 21:09:59 albundy kernel: eth0: Digital DS21140 Tulip at 0xdc00, 00 80 c8 94 41
a8, IRQ 11.
Jan 13 21:09:59 albundy kernel: eth0: EEPROM default media type Autosense.
Jan 13 21:09:59 albundy kernel: eth0: Index #0 - Media MII (#11) described by a 21140
MII PHY (1) block.
Jan 13 21:09:59 albundy kernel: eth0: MII transceiver found at MDIO address 0, config
1000 status 782d.
Jan 13 21:09:59 albundy kernel: Partition check:
Jan 13 21:09:59 albundy kernel: sda: sda1 sda2 sda3 sda4
Jan 13 21:09:59 albundy kernel: sdb: sdb1 sdb2 sdb3 sdb4
Jan 13 21:09:59 albundy kernel: VFS: Mounted root (ext2 filesystem) readonly.
Jan 13 21:09:59 albundy kernel: Adding Swap: 130748k swap-space (priority -1)
Jan 13 21:09:59 albundy kernel: Unable to load NLS charset cp437(nls_cp437)
Jan 13 21:10:11 albundy mountd[297]: NFS mount of /.cfsfs attempted from 127.0.0.1
Jan 13 21:10:11 albundy mountd[297]: /.cfsfs has been mounted by 127.0.0.1
Jan 13 22:59:00 albundy kernel: st: Unloaded.
Jan 13 23:00:22 albundy kernel: st: Unloaded.
Jan 14 10:02:01 albundy kernel: scsi-ncr53c7,8xx : at PCI bus 0, device 10, function 0
Jan 14 10:02:01 albundy kernel: scsi-ncr53c7,8xx : NCR53c825 at memory 0xec000000, io
0xe000, irq 5
Jan 14 10:02:01 albundy kernel: scsi1 : burst length 8
Jan 14 10:02:01 albundy kernel: scsi1 : NCR code relocated to 0xb074600 (virt
0x0b074600)
Jan 14 10:02:01 albundy kernel: scsi1 : test 1 started
Jan 14 10:02:01 albundy kernel: scsi1 : NCR53c{7,8}xx (rel 17)
Jan 14 10:02:01 albundy kernel: scsi : 2 hosts.
Jan 14 10:02:03 albundy kernel: scsi1 : target 2 rejected SDTR
Jan 14 10:02:03 albundy kernel: scsi1 : setting target 2 to asynchronous SCSI
Jan 14 10:02:03 albundy kernel: Vendor: AGFA Model: SNAPSCAN 1236 Rev: 1.40
Jan 14 10:02:03 albundy kernel: Type: Scanner ANSI SCSI
revision: 02
Jan 14 10:02:03 albundy kernel: scsi1 : target 3 accepting period 100ns offset 8
10.00MHz FAST SCSI-II
Jan 14 10:02:03 albundy kernel: scsi1 : setting target 3 to period 100ns offset 8
10.00MHz FAST SCSI-II
Jan 14 10:02:03 albundy kernel: Vendor: HP Model: C1537A Rev: L610
Jan 14 10:02:03 albundy kernel: Type: Sequential-Access ANSI SCSI
revision: 02
Jan 14 10:02:03 albundy kernel: Detected scsi tape st0 at scsi1, channel 0, id 3, lun 0
Jan 14 10:02:03 albundy kernel: scsi1 : target 4 accepting period 100ns offset 8
10.00MHz FAST SCSI-II
Jan 14 10:02:03 albundy kernel: scsi1 : setting target 4 to period 100ns offset 8
10.00MHz FAST SCSI-II
Jan 14 10:02:03 albundy kernel: Vendor: PIONEER Model: CD-ROM DR-U03S Rev: 1.01
Jan 14 10:02:03 albundy kernel: Type: CD-ROM ANSI SCSI
revision: 02
Jan 14 10:02:13 albundy kernel: st: Unloaded.
Jan 14 10:02:15 albundy kernel: Detected scsi tape st0 at scsi1, channel 0, id 3, lun 0
Jan 14 10:03:15 albundy kernel: st: Unloaded.
Jan 14 10:03:18 albundy kernel: Detected scsi tape st0 at scsi1, channel 0, id 3, lun 0
Jan 14 10:04:20 albundy kernel: st: Unloaded.
Jan 14 10:04:25 albundy kernel: Detected scsi tape st0 at scsi1, channel 0, id 3, lun 0
Jan 14 10:05:25 albundy kernel: st: Unloaded.
Jan 14 10:05:27 albundy kernel: Detected scsi tape st0 at scsi1, channel 0, id 3, lun 0
Jan 14 10:07:32 albundy kernel: st: Unloaded.
Jan 14 10:07:32 albundy kernel: Detected scsi tape st0 at scsi1, channel 0, id 3, lun 0
Jan 14 10:08:36 albundy kernel: st: Unloaded.
Jan 14 10:08:57 albundy kernel: Detected scsi tape st0 at scsi1, channel 0, id 3, lun 0
Jan 14 10:10:55 albundy kernel: scsi1 : SCSI FIFO not empty
Jan 14 10:10:55 albundy kernel: scsi1 : illegal instruction
Jan 14 10:10:55 albundy kernel: scsi1 : DCMD|DBC=0x0, DNAD=0x0 (virt 0x00000000)
Jan 14 10:10:55 albundy kernel: DSA=0xb5541e8 (virt 0x0b5541e8)
Jan 14 10:10:55 albundy kernel: DSPS=0x0, TEMP=0xb074854 (virt 0x0b074854),
DMODE=0x98
Jan 14 10:10:55 albundy kernel: SXFER=0x8, SCNTL3=0x13
Jan 14 10:10:55 albundy kernel: BSY phase=DATAIN, 8 bytes in SCSI FIFO
Jan 14 10:10:55 albundy kernel: STEST0=0x5
Jan 14 10:10:55 albundy kernel: scsi1 : DSP 0xb554154 (virt 0x0b554154) ->
Jan 14 10:10:55 albundy kernel: 0xb554154 (virt 0x0b554154) : 0x78388800 0x00000000
(virt 0x00000000)
Jan 14 10:10:55 albundy kernel: 0xb55415c (virt 0x0b55415c) : 0xc0000018 0x0b55405c
(virt 0x0b55405c) 0x0b554044 (virt 0x0b554044)
Jan 14 10:10:55 albundy kernel: 0xb554168 (virt 0x0b554168) : 0x60000040 0x00000000
(virt 0x00000000)
Jan 14 10:10:55 albundy kernel: 0xb554170 (virt 0x0b554170) : 0x90080000 0x00000000
(virt 0x00000000)
Jan 14 10:10:55 albundy kernel: 0xb554178 (virt 0x0b554178) : 0x720a0000 0x00000000
(virt 0x00000000)
Jan 14 10:10:55 albundy kernel: 0xb554180 (virt 0x0b554180) : 0x8084f803 0x00ffff48
(virt 0x00ffff48)
Jan 14 10:10:55 albundy kernel: scsi1 : connected (SDID=0x3, SSID=0x83)
Jan 14 10:10:55 albundy kernel: scsi1 : dsa at phys 0xb5541e8 (virt 0x0b5541e8)
Jan 14 10:10:55 albundy kernel: + 64 : dsa_msgout length = 1, data = 0xb55402c
(virt 0x0b55402c)
Jan 14 10:10:55 albundy kernel: Identify disconnect allowed lun 0
Jan 14 10:10:55 albundy kernel: + 60 : select_indirect = 0x13030800
Jan 14 10:10:55 albundy kernel: + 56 : dsa_cmnd = 0xf047a04
result = 0xffff, target = 3, lun = 0, cmd = Read (6) 00 00 80 00 00
Jan 14 10:10:55 albundy kernel: + 48 : dsa_next = 0x0
Jan 14 10:10:55 albundy kernel: scsi1 target 3 : sxfer_sanity = 0x8, scntl3_sanity =
0x13
Jan 14 10:10:55 albundy kernel: script : 0x78031300 0x0 0x78050800
0x0 0x90080000 0x0 0x0 0x0
Jan 14 10:10:55 albundy kernel: scsi1 : saved data pointer at offset 0
Jan 14 10:10:55 albundy kernel: scsi1 : can't determine active data pointer offset
Jan 14 10:10:55 albundy kernel: 0xb074854 (virt 0x0b074854) : 0x820b0000 0x0b07484c
(virt 0x0b07484c)
Jan 14 10:10:55 albundy kernel: 0xb07485c (virt 0x0b07485c) : 0x8f0b0000 0x0b074a04
(virt 0x0b074a04)
Jan 14 10:10:55 albundy kernel: scsi1 : issue queue
Jan 14 10:10:55 albundy kernel: scsi1 : schedule dsa array :
Jan 14 10:10:55 albundy kernel: scsi1 : end schedule dsa array
Jan 14 10:10:55 albundy kernel: scsi1 : reconnect_dsa_head :
Jan 14 10:10:55 albundy kernel: scsi1 : end reconnect_dsa_head
Jan 14 10:10:55 albundy kernel: mail [EMAIL PROTECTED] with ALL
Jan 14 10:10:55 albundy kernel: boot messages and diagnostic output
Jan 14 10:10:55 albundy kernel: The sti() implicit in a printk() prevents hangs
Jan 14 10:10:55 albundy kernel: scsi1 : nuking commands
Jan 14 10:10:55 albundy kernel: scsi1 : done.
Jan 14 10:10:55 albundy kernel: scsi1 : disabled. Unload and reload
Jan 14 10:25:55 albundy kernel: scsi : aborting command due to timeout : pid 53461,
scsi1, channel 0, id 3, lun 0 Read (6) 00 00 80 00 00
Jan 14 10:25:55 albundy kernel: scsi1 : did this command ever run?
Jan 14 10:25:55 albundy kernel: scsi1 : disabled or bad target 3 lun 0
Jan 14 10:25:55 albundy kernel: st0: Error 25040000.
Jan 14 10:26:45 albundy kernel: st: Unloaded.
==============3DACA717C3537A89769C6639==
------------------------------
** FOR YOUR REFERENCE **
The service address, to which questions about the list itself and requests
to be added to or deleted from it should be directed, is:
Internet: [EMAIL PROTECTED]
You can send mail to the entire list (and comp.os.linux.development.system) via:
Internet: [EMAIL PROTECTED]
Linux may be obtained via one of these FTP sites:
ftp.funet.fi pub/Linux
tsx-11.mit.edu pub/linux
sunsite.unc.edu pub/Linux
End of Linux-Development-System Digest
******************************
