Hi Doug
On 3/23/2018 5:34 PM, Doug Anderson wrote:
> Hi,
>
> On Fri, Mar 23, 2018 at 1:20 PM, Karthikeyan Ramasubramanian
> <[email protected]> wrote:
>> This bus driver supports the GENI based i2c hardware controller in the
>> Qualcomm SOCs. The Qualcomm Generic Interface (GENI) is a programmable
>> module supporting a wide range of serial interfaces including I2C. The
>> driver supports FIFO mode and DMA mode of transfer and switches modes
>> dynamically depending on the size of the transfer.
>>
>> Signed-off-by: Karthikeyan Ramasubramanian <[email protected]>
>> Signed-off-by: Sagar Dharia <[email protected]>
>> Signed-off-by: Girish Mahadevan <[email protected]>
>> ---
>> drivers/i2c/busses/Kconfig | 13 +
>> drivers/i2c/busses/Makefile | 1 +
>> drivers/i2c/busses/i2c-qcom-geni.c | 650
>> +++++++++++++++++++++++++++++++++++++
>> 3 files changed, 664 insertions(+)
>
> [...]
>
>> +/*
>> + * Hardware uses the underlying formula to calculate time periods of
>> + * SCL clock cycle. Firmware uses some additional cycles excluded from the
>> + * below formula and it is confirmed that the time periods are within
>> + * specification limits.
>
> I was hoping for more than just "oh, and there's a fudge factor", but
> I guess this is the best I'm going to get?
>
According to our HW/FW team:
"We use over sampling in our FW and we use 1-2 NOPE extra in some cases.
this is why we can’t give a exact formula."
>
>> +static int geni_i2c_probe(struct platform_device *pdev)
>> +{
>> + struct geni_i2c_dev *gi2c;
>> + struct resource *res;
>> + u32 proto, tx_depth;
>> + int ret;
>> +
>> + gi2c = devm_kzalloc(&pdev->dev, sizeof(*gi2c), GFP_KERNEL);
>> + if (!gi2c)
>> + return -ENOMEM;
>> +
>> + gi2c->se.dev = &pdev->dev;
>> + gi2c->se.wrapper = dev_get_drvdata(pdev->dev.parent);
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> + gi2c->se.base = devm_ioremap_resource(&pdev->dev, res);
>> + if (IS_ERR(gi2c->se.base))
>> + return PTR_ERR(gi2c->se.base);
>> +
>> + gi2c->se.clk = devm_clk_get(&pdev->dev, "se");
>> + if (IS_ERR(gi2c->se.clk)) {
>> + ret = PTR_ERR(gi2c->se.clk);
>> + dev_err(&pdev->dev, "Err getting SE Core clk %d\n", ret);
>> + return ret;
>> + }
>> +
>> + ret = device_property_read_u32(&pdev->dev, "clock-frequency",
>> + &gi2c->clk_freq_out);
>> + if (ret) {
>> + /* Clock frequency not specified, so default to 100kHz. */
>> + dev_info(&pdev->dev,
>> + "Bus frequency not specified, default to 100kHz.\n");
>
> If you happen to spin again, can you remove the comment since it's
> obvious from the string in the print? It looks a lot like this code:
>
> /* Print hello, world */
> printf("hello, world\n");
>
>
> In any case, that's a pretty minor nit, so I'll add:
>
> Reviewed-by: Douglas Anderson <[email protected]>
>
> ...assuming that the bindings and "geni" code get Acked / landed
> somewhere. Ideally let's not land this before the geni code lands
> since if the geni API changes for some reason it'll cause us grief.
>
Sure, thanks a lot for reviewing the patches!
-Sagar
>
> -Doug
>
--
Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
