On Thu, Mar 13, 2008 at 1:20 PM, Jarryd Beck <[EMAIL PROTECTED]> wrote: > > On Thu, Mar 13, 2008 at 10:11 AM, Antti Palosaari <[EMAIL PROTECTED]> wrote: > > Jarryd Beck wrote: > > > On Thu, Mar 13, 2008 at 8:14 AM, <[EMAIL PROTECTED]> wrote: > > > > >> Then, please turn ON debug, repeat your tests, and post again with > > >> dmesg. I am not familiar with the af9015 driver, but for tda18271, > set > > >> debug=1. (you must unload all modules first -- do 'make unload' in > the > > >> v4l-dvb dir, then replug your device) > > >> > > >> -Mike > > >> > > >> > > > > > > Sorry I'm unsure where to set debug. > > > > > > Jarryd. > > > > I added initial support for this tda-tuner to the driver. Jarryd, can > > you test? > > http://linuxtv.org/hg/~anttip/af9015_new/ > > > > There is debug switch in af9013 module that may be helpful if it does > > not work. You can enable it as described or if it is too hard to play > > with modprobe just edit af9013.c file in frontend directory and set > > debug=1 by hard coding. > > If it does not work you can also try set GPIO3 setting (af9015) to 0xb > > instead 0x3 used currently. Also try to change rf-spectral inversion to > > see if it helps. Firmware should be ok and all other settings as well as > > I can see from usb-sniffs. With little lucky it should start working. > > > > regards > > Antti > > -- > > http://palosaari.fi/ > > > > Thanks, but now for some reason all I get is this: > > usb 2-10: new high speed USB device using ehci_hcd and address 6 > > usb 2-10: configuration #1 chosen from 1 choice > input: Leadtek WinFast DTV Dongle Gold as /class/input/input8 > > input: USB HID v1.01 Keyboard [Leadtek WinFast DTV Dongle Gold] on > usb-0000:00:02.1-10 > > af9015_usb_probe: > af9015_identify_state: reply:01 > dvb-usb: found a 'Afatech AF9015 DVB-T USB2.0 stick' in cold state, > > will try to load a firmware > dvb-usb: downloading firmware from file 'dvb-usb-af9015.fw' > af9015_download_firmware: > usbcore: registered new interface driver dvb_usb_af9015 > > Jarryd. >
I found the problem, the driver I had set .no_reconnect = 1 in af9015_properties, the one in af9015_new didn't. So after I changed that I tried again, it still didn't work. I enabled debugging and tried to tune to a channel and this is what I got in dmesg. usb 2-10: new high speed USB device using ehci_hcd and address 27 usb 2-10: configuration #1 chosen from 1 choice af9015_usb_probe: af9015_identify_state: reply:01 dvb-usb: found a 'Afatech AF9015 DVB-T USB2.0 stick' in cold state, will try to load a firmware dvb-usb: downloading firmware from file 'dvb-usb-af9015.fw' af9015_download_firmware: dvb-usb: found a 'Afatech AF9015 DVB-T USB2.0 stick' in warm state. dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. DVB: registering new adapter (Afatech AF9015 DVB-T USB2.0 stick) af9015_eeprom_dump: 00: 31 c2 bb 0b 00 00 00 00 13 04 29 60 00 02 01 02 10: 00 80 00 fa fa 10 40 ef 01 30 31 30 31 30 32 30 20: 35 30 35 30 30 30 30 31 ff ff ff ff ff ff ff ff 30: 00 00 3a 01 00 08 02 00 cc 10 00 00 9c ff ff ff 40: ff ff ff ff ff 08 02 00 1d 8d c4 04 82 ff ff ff 50: ff ff ff ff ff 26 00 00 04 03 09 04 10 03 4c 00 60: 65 00 61 00 64 00 74 00 65 00 6b 00 30 03 57 00 70: 69 00 6e 00 46 00 61 00 73 00 74 00 20 00 44 00 80: 54 00 56 00 20 00 44 00 6f 00 6e 00 67 00 6c 00 90: 65 00 20 00 47 00 6f 00 6c 00 64 00 20 03 30 00 a0: 31 00 30 00 31 00 30 00 31 00 30 00 31 00 30 00 b0: 36 00 30 00 30 00 30 00 30 00 31 00 00 ff ff ff c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff af9015_read_config: xtal:2 set adc_clock:28000 af9015_read_config: tuner id1:156 af9015_read_config: spectral inversion:0 af9015_set_gpios: af9013: firmware version:4.95.0 DVB: registering frontend 0 (Afatech AF9013 DVB-T)... af9015_tuner_attach: af9015_tda18271_tuner_attach: tda18271 5-00c0: creating new instance TDA18271HD/C1 detected @ 5-00c0 tda18271_init_regs: initializing registers for device @ 5-00c0 input: IR-receiver inside an USB DVB receiver as /class/input/input39 dvb-usb: schedule remote query interval to 200 msecs. dvb-usb: Afatech AF9015 DVB-T USB2.0 stick successfully initialized and connected. af9015_init: af9015_download_ir_table: input: Leadtek WinFast DTV Dongle Gold as /class/input/input40 input: USB HID v1.01 Keyboard [Leadtek WinFast DTV Dongle Gold] on usb-0000:00:02.1-10 tda18271_set_standby_mode: sm = 0, sm_lt = 0, sm_xt = 0 tda18271_init_regs: initializing registers for device @ 5-00c0 tda18271_tune: freq = 219500000, ifc = 3800000, bw = 7000000, std = 0x1d tda18271_set_standby_mode: sm = 0, sm_lt = 0, sm_xt = 0 tda18271_init_regs: initializing registers for device @ 5-00c0 tda18271_set_standby_mode: sm = 1, sm_lt = 0, sm_xt = 0 Jarryd. _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
