Linux-Hardware Digest #623, Volume #14 Sat, 14 Apr 01 11:13:07 EDT
Contents:
I2c question ("Andrew Diaczyk")
Re: today's harddrives will surely fail before dialup users manage to fill them up?
(J. Clarke)
Re: Pinout: Serial RJ45 for Barcode Scanners (Rod Carty)
Re: Motherboard problems ("Colin G.")
Re: today's harddrives will surely fail before dialup users manage to fill them up?
(Patrick Schaaf)
Re: Linux support for Maxtor Ultra ATA100 PCI card? ("Jason Lu")
Re: SCSI errors, why? (Dave Martindale)
Re: Newbie to Linux with Modem Problems ("Jali")
Re: Sandisk SDDR31 USB Help needed ("Peter T. Breuer")
Re: Motherboard problems (Robert Hampf)
Re: Problem with (fixed frequency?) Ikegami ct-20 on pc.. (Ton)
Ensoniq Soundscape ISA PnP (modell 2) ("MBNalbach")
Re: Audio with Linux (2.4.2/2.2.16) kernel and Asus AV7133 ("Larry Snyder")
duron linux system advice wanted (Alan Needleman)
Missing XF86_SVGA???? ("Eric Hallett")
Re: Controlling network printer ("carpahacer")
Re: howto properly access serial devices in Perl or C (Ulrich Eckhardt)
----------------------------------------------------------------------------
From: "Andrew Diaczyk" <[EMAIL PROTECTED]>
Crossposted-To:
ahn.tech.linux,alt.linux,alt.os.linux,comp.os.linux,comp.os.linux.help,comp.os.linux.misc,comp.os.linux.questions
Subject: I2c question
Date: Sat, 14 Apr 2001 04:42:34 GMT
in the documentation for the new i2c drivers. It says you need an original
kernel tree or a vanilla kernel tree. First of all what is a kernel tree
where is it located. How do I set a kernel tree up on a fresh install of
linux 6.2.
------------------------------
From: J. Clarke <[EMAIL PROTECTED]>
Crossposted-To: comp.arch.storage,comp.sys.ibm.pc.hardware.storage
Subject: Re: today's harddrives will surely fail before dialup users manage to fill
them up?
Date: Sat, 14 Apr 2001 01:12:29 -0400
In article <[EMAIL PROTECTED]>, [EMAIL PROTECTED] says...
> In article <8FjB6.388105$[EMAIL PROTECTED]>, Dave wrote:
> >Dan Jacobson <[EMAIL PROTECTED]> wrote in message
> >news:[EMAIL PROTECTED]...
> >> It seems that at least for a home dialup user, today's PC hard disks
> >> would surely fail before he could manage to fill it all up via say,
> >> browsing, even with caching proxies, etc. Therefore it seems deleting
> >> unneeded files might become a routine of the past? Hmm, 30 GB /(20
> >> MB/day)=4 years
> >> --
> >> http://www.geocities.com/jidanni Tel886-4-25854780 e-mail:restore .com.
> >
> >Nope, a heavily laden cache will eventually make the browser to slow to use.
> >Still got to get rid of the dead weight.
> >Dave
>
> (post at the bottom please)
>
> if that's the case then your cache software needs a rewrite, HTH.
Oh? Care to provide us with the algorithm that performs searches of
large directories as quickly as it does small ones?
--
--
--John
Reply to jclarke at ae tee tee global dot net
(used to be jclarke at eye bee em dot net)
------------------------------
From: Rod Carty <[EMAIL PROTECTED]>
Crossposted-To:
comp.hardware,comp.sys.ibm.pc.hardware.comm,comp.sys.ibm.pc.hardware.misc,comp.sys.mac.hardware.misc
Subject: Re: Pinout: Serial RJ45 for Barcode Scanners
Date: Sat, 14 Apr 2001 05:44:39 GMT
Karsten Jeppesen wrote:
>
> I have not been able to find this pinout anywhere.
>
> Barcode wands and barcode scanners often comes with RJ45 interface. It is
> a RJ45 connector, but it is serial. TTL not fully RS232 though.
>
> It usually includes 5V on one of the pins.
>
> Anybody knows the pinout on that one?
>
> TIA
> Karsten
What brand and model of barcode wand?
Here's a website that I've found useful on more than one occasion. This
page is the one for point of sale equipment, but you may find what
you're looking for on one of the other pages - just use the domain part
of the URL for their home page and follow the links.
http://www.pin-outs.com/directory//Hardware/Point_of_Sale/
--
Rod C--
Enterprise Network Consulting
Whitehorse, Yukon
http://www.enc.yk.net/
http://members.nbci.com/rodcarty/
http://community.webshots.com/user/rodcarty
>> Si hoc legere scis nimium eruditionis habes. (If you can read this, you're
>overeducated.) <<
The preceding humor inserted by QuipSig
http://www.enc.yk.net/quipsig/
4,000 quip repertory!
------------------------------
From: "Colin G." <[EMAIL PROTECTED]>
Subject: Re: Motherboard problems
Date: Sat, 14 Apr 2001 05:55:48 GMT
I'm running an ASUS A7V with an Athlon 850 MHz Thunderbird processor. I've
experienced no problems under linux what-so-ever.
Just trying to help you rule out boards that aren't causing any problems.
--
Colin G.
coling (at) intrive (dot) com
"Philip" <[EMAIL PROTECTED]> wrote in message
news:[EMAIL PROTECTED]...
> I was just informed that there are problems with some ASUS motherboards
> and the Athlon processor running Linux. Can anyone tell me which boards
> are the problem.
> And just out of curiosity why is Linux affected by this problem and not
> Windows.
>
> Then again this may be bogus information. I'm trying to get
> confirmation.
>
------------------------------
Crossposted-To: comp.arch.storage,comp.sys.ibm.pc.hardware.storage
Subject: Re: today's harddrives will surely fail before dialup users manage to fill
them up?
From: [EMAIL PROTECTED] (Patrick Schaaf)
Date: 14 Apr 2001 06:15:19 GMT
J. Clarke <[EMAIL PROTECTED]> writes:
>Oh? Care to provide us with the algorithm that performs searches of
>large directories as quickly as it does small ones?
Get a book on databases.
Anyway, the question is stupid. For a web browser cache application,
you only need to be faster than the network connection; no need
to be faster than not doing anything at all, as that's not equivalent.
regards
Patrick
------------------------------
From: "Jason Lu" <[EMAIL PROTECTED]>
Subject: Re: Linux support for Maxtor Ultra ATA100 PCI card?
Date: Sat, 14 Apr 2001 14:23:19 +0800
It is a PROMISE ATA100 card. Just following UDMA-mini-HOWTO.
Step by step like PROMISE Ultra33.
or Use new kernal 2.4.x which support PROMSE ATA chipset already.
"Richard M. Denney" <[EMAIL PROTECTED]> ?????
news:[EMAIL PROTECTED]...
> Does anyone know whether ATA100 IDE drives attached to the Maxtor Ultra
> ATA 100 PCI card would be recognized under linux? Do these fast drives
> provide high speed under linux? The software drivers provided with the
> card mention only windows operating systems.
>
> Rick Denney
>
------------------------------
From: [EMAIL PROTECTED] (Dave Martindale)
Subject: Re: SCSI errors, why?
Date: 14 Apr 2001 01:44:26 -0700
Trevor Jenkins <[EMAIL PROTECTED]> writes:
>But the Zip drive isn't the last device on the bus. I knew enough to
>turn off termination on the Zip drive before powering up. :-)
>Although I say Zip it's actually a Zip 250 rather than the original 100.
Does it still use the stupid 25-pin SCSI connectors? SCSI is really
supposed to use almost 40 wires, with separate ground wires for many of
the signals. With a 25-pin SCSI connector, many of the grounds need to
be shorted together in the connector on the cable. When I was running
a Mac system with multiple external SCSI devices, I found that having
the Zip drive in the SCSI chain was always somewhat problematic. I
found that putting the Zip drive at the end, of the bus so at least all
the other devices had proper 50-pin connections, minimized these
problems.
I don't think there's any problem using the Zip's internal terminator.
However, the drive does not provide external termination power.
Normally this isn't a problem, because the SCSI controller in the PC
ought to be configured to provide terminator power. There *was* a
problem with Powerbooks - for some reason the Powerbook didn't provide
terminator power, and if the Zip didn't either, and there wasn't
any other device providing terminator power, then your external
terminator wouldn't work properly. But this shouldn't be a problem
on a PC.
Dave
------------------------------
From: "Jali" <[EMAIL PROTECTED]>
Subject: Re: Newbie to Linux with Modem Problems
Date: Sat, 14 Apr 2001 11:09:25 +0100
In article <wLHB6.569360$[EMAIL PROTECTED]>, "Chris
Routh" <[EMAIL PROTECTED]> wrote:
[...]
>
> PC: Intel 300mhz Celeron, 64MB Ram, 10GB HD running Windows 98 SE and
> Linux Mandrake 6.1 I installed linux on a second partition and am using
> Boot Magic PQ because I don't know anything about LILO I went into the
> KDE interface as root I ran KPPP dialer and set up my connection, my
> modem is set to PnP now but was set to Com2 IRQ3 orginally I tested the
> modem using the button in the dialer and everything checked out. I tried
> dialing and got "Sorry, Modem doesn't respond" I went back to testing
> and got "Sorry, Modem doesn't respond" there.. I've tried everything I
> can figure out how to do.. and can't get it to work.. also. my manual
> for my linux distribution doesn't cover modems..
>
> Routhy Chris Routh http://www.routhy.net
>
>
Hi!
Try to find out wether you have physical access to the modem so far. An
easy way is to send an inittialisation string to the modem and see if it
responds. To do this you can either send an echo ATZ++ >/dev/modem on the
command line, and watch the LEDs on your modem, or use a program like
minicom. If it is properly configured to the modem settings the modem
should respond with OK. Try this on /dev/ttyS0 to /dev/ttyS3. Keep in
mind that what's COM2: in Windows/DOS is /dev/ttyS1 in Linux, for the
latter starts counting the devices by 0. If you finally found out which
serial port your modem is connected to, you should set
/dev/modem to it. If your configuration tool doesn't properly do that you
can set it by hand using the command ln -s /dev/ttyS1 /dev/modem as root.
If your modem is on an other port than /dev/ttyS1 you'll have to set its
name instead of course. If you still don't have access to the modem,
maybe your kernel doesn't support serial devices. If you didn't compile
your own kernel yet, this will be very unusual, but it's possible of
course. To compile a new kernel you must have the kernel sources
installed. For kernel compilation you'll have to be root, since you cannot
install the new kernel as another user. Change directory to /usr/src/linux
and type make menuconfig. Usually all options should be preconfigured to
good values, but it's a good idea to read the Kernel-HOWTO first. Go to
the section Character Devices and make sure that "Standard/generic (dumb)
serial support is enabled, either static (with a *) or as a module (M). If
it is not you have to select it and recompile a new kernel. Refer to the
Kernel-Howto for details.
Hope this helps. regards, Alex
------------------------------
From: "Peter T. Breuer" <[EMAIL PROTECTED]>
Subject: Re: Sandisk SDDR31 USB Help needed
Date: Sat, 14 Apr 2001 11:17:24 +0200
Dances With Crows <[EMAIL PROTECTED]> wrote:
> On Fri, 13 Apr 2001 16:13:13 +0200, Schubert staggered into the Black
> Sun and said:
>>I want to access my compactflash memory card via the sandisk SDDR31
>>Reader (USB) to the linux system. I'm using SuSE Distr.+ Kernel 2.2.16
>>and compiled the USB-modules (Besemodule and the Mass Storage Module).
> USB support did not fully stabilize in the 2.2.x series until kernel
> 2.2.18. SuSE's 2.2.16 with USB patches isn't quite up to snuff; for
I happily ported the 2.2.18 usb stuff back to 2.2.15 (then found out
later there was an official patch). It works fine because it IS the
same. The port consisted of adding a few macros to supply functions
that 2.2.15 didn't have - the only thing I couldn't do was the ibmcia
(I think I recall) which required physical memory mapping that
I didn't want to go near.
> instance, I have a USB gamepad that doesn't work at all with their
> kernel yet works on a 2.4.3 kernel.
Maybe it also needs some of the physmem support. But comparing it
against 2.4.3 isn't fair. I'm very happy with the way the back-port
works.
>>linux kernel: usb.c: USB new device connect, assigned device number 2
>>linux kernel: usb.c: This device is not recognized by any installed USB
Well, seems he forgot to load a driver!
>>driver.
>>linux kernel: hub.c: already running port 2 disabled by hub (EMI?),
>>re-enabling...
>>linux kernel: usb.c: USB disconnect on device 2
>>linux kernel: usb.c: USB new device connect, assigned device number 2
>>linux kernel: usb.c: This device is not recognized by any installed USB
>>driver.
> Did you "modprobe usb-storage"? This message is telling you that the
> USB base system found a device, but said base system doesn't take care
> of auto-loading the appropriate module for that device. A user-space
> utility called "hotplug" is supposed to take care of that, but from the
I've never heard of it.
> hotplug project site, it's not quite all there yet for 2.2.x kernels.
> Try loading usb-storage , plugging in the device, and then attempting to
> access /dev/sdX or /dev/sdX1 , where X will be "a" unless you have other
> SCSI devices attached. HTH, bonne chance....
Sounds good advice. Visiting the linux-usb.org pages is also on his
itinerary.
Peter
------------------------------
From: [EMAIL PROTECTED] (Robert Hampf)
Subject: Re: Motherboard problems
Date: Sat, 14 Apr 2001 13:31:48 +0300
Philip <[EMAIL PROTECTED]> h�lt �essu fram:
:
: I was just informed that there are problems with some ASUS motherboards
: and the Athlon processor running Linux. Can anyone tell me which boards
: are the problem.
There was something about this on www.theregister.co.uk yesterday.
Apparently there is a bug in a Via chip. There seems to be a fix for
this in the latest kernels. I wonder whether this also includes the
2.2.19.
: And just out of curiosity why is Linux affected by this problem and not
: Windows.
It affects Windows also.
rh
------------------------------
From: Ton <[EMAIL PROTECTED]>
Crossposted-To: comp.sys.ibm.pc.hardware.video,comp.sys.mac.hardware.video
Subject: Re: Problem with (fixed frequency?) Ikegami ct-20 on pc..
Date: Sat, 14 Apr 2001 12:47:23 +0200
ks wrote:
> Basically, if you want it to work, you're going to have to get the proper
> video card. I've just gone through your whole sequence of events myself, so
> I know first hand...
> Check out:
> www.si87.com
> and check out the Saturn GL. that will fix your problem...
> As far as other fixes, they do exist, but at $140, I think this is your best
> option.
> Keith
> [EMAIL PROTECTED]
Thanks Keith,
I was told is should work at 64k horizontal/60Hz vertical so it probably is
broken, since I've tried some 'mistuning' to get my current card on that freqs.
I saw the si87 site before and the option of the Saturn card, but tell me, can
you explain why I should get this card and not be able to use a 'normal' one? I
can live without the low resolutions, so only need the high res mode. Do you
think it is absolutely necessary to get it working because of the exact freqs
which I might not get by mistuning mine, and so the monitor might not even be
broken?
Thanks,
Ton
------------------------------
From: "MBNalbach" <[EMAIL PROTECTED]>
Subject: Ensoniq Soundscape ISA PnP (modell 2)
Date: Sat, 14 Apr 2001 13:30:08 +0200
Ich habe in meinem Linux Rechner eine Ensoniq Soundscape ISA PnP (modell 2)
Karte und bekomme sie leider nicht zum Laufen. Suse Linux 7.1 Prof. bringt
zu dieser karte nicht einen einzigen treiber mit. Dann wollte ich sie mit
OSS (www.opensound.de) zum Laufen bringen. Leider fragt mich OSS nach einem
Firmware-file, das ich nicht habe und auch nirgends finde, da die FTP�s die
opensound angibt alle platt sind. :-(
---schnipp---
Name of the firmware file (sndscape.co#) is asked by soundconf when
a soundscape card is added to the configuration. The # in the name
is a number between 0 and 4 and depends on the model of the card.
OSS requires at least version 3.0 of the firmware files. Currently
these files are only included in the DOS/Windows driver packege
which is distributed with the card and is also available from
ftp://ftp.ensoniq.com.
---schnapp---
MFG *der-soundlose* MBNalbach
------------------------------
From: "Larry Snyder" <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.setup,alt.comp.periphs.mainboard.asus
Subject: Re: Audio with Linux (2.4.2/2.2.16) kernel and Asus AV7133
Date: Sat, 14 Apr 2001 08:01:04 -0400
Can you give me an idea of what to check for?
For example, when bring up real player 8 (basic/standard) I hear in the
background the "theme" music but I also hear static/white noise..
Any help would be appreciated..
Cheers..
"Unstable" <[EMAIL PROTECTED]> wrote in message
news:IbEB6.4845$[EMAIL PROTECTED]...
> It might be a configuration problem with the real player, not the onboard
> sound.
> Look at the settings in real player and see if something is set wrong.
>
> "Larry Snyder" <[EMAIL PROTECTED]> wrote in message
> news:%LrB6.6586$[EMAIL PROTECTED]...
> > I have been unable to get the onboard audio to work with my Asua A7V133
> > under Linux - it works just fine under Windows 2K.
> >
> > The audio hardware is detected at boot time - when I try to stream audio
> > using the real player I get lots of static (but I can make out the music
> in
> > the background)..
> >
> > When I log into the machine (using Mandrake 8 Beta 3) I do get the
"login"
> > WAV played just fine..
> >
> > Any ideas?
> >
> > Larry
> >
> >
>
>
------------------------------
From: Alan Needleman <[EMAIL PROTECTED]>
Subject: duron linux system advice wanted
Date: Sat, 14 Apr 2001 12:43:05 GMT
Hi,
My old PII 350 MHz system at home seems to be slowly dying (memory
errors - could be the cache - and disk noises). I use it mainly for
writing, web access, burning music cd's and some programming
(computational). I found an AMD Duron system from Cyberpower that seems
reasonably priced ($560 - no monitor) with a 750 MHz Duron, 256MB, 20GB
disk (UDMA 66), ATI 2000 video card with 32 MB. The motherboard is an
Azza using the VIA KT133 chipset. (I would use the CDRW and USB ZIP disk
I added to the old system.) Does anyone have experience with such a
system running linux? Are there gotcha's I should look out for? Any
experience with that vendor? Any vendor recommendations? Any suggestions
welcome. Thanks. -- Alan
------------------------------
From: "Eric Hallett" <[EMAIL PROTECTED]>
Subject: Missing XF86_SVGA????
Date: Sat, 14 Apr 2001 20:18:03 +0700
I'm new to Linux--Redhat 7
I used Xconfigurator to locate my video card. It listed XF86_SVGA as the
server for my Rendition V2200. After hitting OK, I got this message...
Server doesn't exist, can't continue. tried to use
../../usr/X11R6/bin/XF86_SVGA
I need some help with this. What should this newbie do next?
Thanks
------------------------------
From: "carpahacer" <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.x,alt.os.linux.redhat,alt.linux
Subject: Re: Controlling network printer
Date: Sun, 15 Apr 2001 00:43:12 +1000
This is a multi-part message in MIME format.
=======_NextPart_000_00FC_01C0C545.0D1E51C0
Content-Type: text/plain;
charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
The 4219 printer is difficult to setup.
You have to rarp to the printer to configure the network card's ip =
address then telnet <host> 2002.
rarp isn't installed in most disrtributions these days, so you might =
have to install it as a module.
read man rarp
rarp -s hostname hw_addr
--set hostname hw_addr
Create a RARP address mapping entry for host host=AD
name with hardware address set to hw_addr class,
but for most classes one can assume that the usual
presentation can be used. For the Ethernet class,
this is 6 bytes in hexadecimal, separated by
colons.
Chris
"Victor" <[EMAIL PROTECTED]> wrote in message =
news:3ad7a174$0$25510$[EMAIL PROTECTED]...
> G'day Folks
>=20
> I have an old Xerox 4219/MRP laser printer that has the capability to =
run as
> a network printer. Xerox does apparently have some TCP/IP software for =
it
> for Unix.
> The printer itself has an rj-45 and aui connector on the back but says =
the
> networking is not configured when the configuration tests are run.
>=20
> Does anybody know of similar software for Linux (Redhat 7.0).
> It would be interesting to see it working.
>=20
> cheers
>=20
> /Victor
>=20
>=20
=======_NextPart_000_00FC_01C0C545.0D1E51C0
Content-Type: text/html;
charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META content=3D"text/html; charset=3Diso-8859-1" =
http-equiv=3DContent-Type>
<META content=3D"MSHTML 5.00.2920.0" name=3DGENERATOR>
<STYLE></STYLE>
</HEAD>
<BODY>
<DIV><FONT face=3DArial size=3D2>The 4219 printer is difficult to=20
setup.</FONT></DIV>
<DIV><FONT face=3DArial size=3D2>You have to rarp to the printer to =
configure the=20
network card's ip address</FONT><FONT face=3DArial size=3D2> then telnet =
<host> 2002.</FONT></DIV>
<DIV><FONT face=3DArial size=3D2>rarp isn't installed in most =
disrtributions these=20
days, so you might have to install it as a module.</FONT></DIV>
<DIV><FONT face=3DArial size=3D2>read man rarp</FONT></DIV>
<DIV><FONT face=3DArial size=3D2>rarp -s hostname hw_addr</FONT></DIV>
<DIV><FONT face=3DArial size=3D2> =
--set hostname=20
hw_addr<BR> &n=
bsp; =20
Create a RARP address mapping entry for host=20
host­<BR> =
=20
name with hardware address set to hw_addr =20
class,<BR> &nb=
sp; =20
but for most classes one can assume that the=20
usual<BR> &nbs=
p; =20
presentation can be used. For the Ethernet =20
class,<BR> &nb=
sp; =20
this is 6 bytes in hexadecimal, =20
separated =20
by<BR> &=
nbsp; =20
colons.</FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>Chris</FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2><BR> </DIV></FONT>
<DIV><FONT face=3DArial size=3D2>"Victor" <</FONT><A=20
href=3D"mailto:[EMAIL PROTECTED]"><FONT face=3DArial=20
size=3D2>[EMAIL PROTECTED]</FONT></A><FONT face=3DArial size=3D2>> =
wrote in=20
message </FONT><A=20
href=3D"news:3ad7a174$0$25510$[EMAIL PROTECTED]"><FONT =
face=3DArial=20
size=3D2>news:3ad7a174$0$25510$[EMAIL PROTECTED]</FONT>=
</A><FONT=20
face=3DArial size=3D2>...</FONT></DIV><FONT face=3DArial size=3D2>> =
G'day=20
Folks<BR>> <BR>> I have an old Xerox 4219/MRP laser printer that =
has the=20
capability to run as<BR>> a network printer. Xerox does apparently =
have some=20
TCP/IP software for it<BR>> for Unix.<BR>> The printer itself has =
an rj-45=20
and aui connector on the back but says the<BR>> networking is not =
configured=20
when the configuration tests are run.<BR>> <BR>> Does anybody know =
of=20
similar software for Linux (Redhat 7.0).<BR>> It would be interesting =
to see=20
it working.<BR>> <BR>> cheers<BR>> <BR>> /Victor<BR>> =
<BR>>=20
</FONT></BODY></HTML>
=======_NextPart_000_00FC_01C0C545.0D1E51C0==
------------------------------
From: Ulrich Eckhardt <[EMAIL PROTECTED]>
Subject: Re: howto properly access serial devices in Perl or C
Crossposted-To:
comp.os.linux.development.apps,comp.os.linux.development.system,de.alt.comm.isdn4linux
Date: Sat, 14 Apr 2001 12:56:32 +0200
Ingo Ciechowski wrote:
> I'd like to access some serial device on my linux box bidirectionally, but
> for some reason don't get connected to the device. Seems as if special
> precautions are required...
there's the serial-programming howto with some C examples
------------------------------
** FOR YOUR REFERENCE **
The service address, to which questions about the list itself and requests
to be added to or deleted from it should be directed, is:
Internet: [EMAIL PROTECTED]
You can send mail to the entire list by posting to comp.os.linux.hardware.
Linux may be obtained via one of these FTP sites:
ftp.funet.fi pub/Linux
tsx-11.mit.edu pub/linux
sunsite.unc.edu pub/Linux
End of Linux-Hardware Digest
******************************
