On Tue, May 28, 2019 at 09:46:47PM +0200, Marek Vasut wrote:
> On 5/28/19 9:35 PM, Heiner Kallweit wrote:
> > On 28.05.2019 21:31, Marek Vasut wrote:
> >> On 5/28/19 9:28 PM, Heiner Kallweit wrote:
> >>> On 28.05.2019 21:23, Marek Vasut wrote:
> >>>> Add support for handling the TJA11xx PHY IRQ signal.
> >>>>
> >>>> Signed-off-by: Marek Vasut <[email protected]>
> >>>> Cc: Andrew Lunn <[email protected]>
> >>>> Cc: Florian Fainelli <[email protected]>
> >>>> Cc: Guenter Roeck <[email protected]>
> >>>> Cc: Heiner Kallweit <[email protected]>
> >>>> Cc: Jean Delvare <[email protected]>
> >>>> Cc: [email protected]
> >>>> ---
> >>>> V2: - Define each bit of the MII_INTEN register and a mask
> >>>> - Drop IRQ acking from tja11xx_config_intr()
> >>>> ---
> >>>> drivers/net/phy/nxp-tja11xx.c | 48 +++++++++++++++++++++++++++++++++++
> >>>> 1 file changed, 48 insertions(+)
> >>>>
> >>>> diff --git a/drivers/net/phy/nxp-tja11xx.c
> >>>> b/drivers/net/phy/nxp-tja11xx.c
> >>>> index b705d0bd798b..b41af609607d 100644
> >>>> --- a/drivers/net/phy/nxp-tja11xx.c
> >>>> +++ b/drivers/net/phy/nxp-tja11xx.c
> >>>> @@ -40,6 +40,29 @@
> >>>> #define MII_INTSRC_TEMP_ERR BIT(1)
> >>>> #define MII_INTSRC_UV_ERR BIT(3)
> >>>>
> >>>> +#define MII_INTEN 22
> >>>> +#define MII_INTEN_PWON_EN BIT(15)
> >>>> +#define MII_INTEN_WAKEUP_EN BIT(14)
> >>>> +#define MII_INTEN_PHY_INIT_FAIL_EN BIT(11)
> >>>> +#define MII_INTEN_LINK_STATUS_FAIL_EN BIT(10)
> >>>> +#define MII_INTEN_LINK_STATUS_UP_EN BIT(9)
> >>>> +#define MII_INTEN_SYM_ERR_EN BIT(8)
> >>>> +#define MII_INTEN_TRAINING_FAILED_EN BIT(7)
> >>>> +#define MII_INTEN_SQI_WARNING_EN BIT(6)
> >>>> +#define MII_INTEN_CONTROL_ERR_EN BIT(5)
> >>>> +#define MII_INTEN_UV_ERR_EN BIT(3)
> >>>> +#define MII_INTEN_UV_RECOVERY_EN BIT(2)
> >>>> +#define MII_INTEN_TEMP_ERR_EN BIT(1)
> >>>> +#define MII_INTEN_SLEEP_ABORT_EN BIT(0)
> >>>> +#define MII_INTEN_MASK
> >>>> \
> >>>> + (MII_INTEN_PWON_EN | MII_INTEN_WAKEUP_EN |
> >>>> \
> >>>> + MII_INTEN_PHY_INIT_FAIL_EN | MII_INTEN_LINK_STATUS_FAIL_EN |
> >>>> \
> >>>> + MII_INTEN_LINK_STATUS_UP_EN | MII_INTEN_SYM_ERR_EN |
> >>>> \
> >>>> + MII_INTEN_TRAINING_FAILED_EN | MII_INTEN_SQI_WARNING_EN |
> >>>> \
> >>>> + MII_INTEN_CONTROL_ERR_EN | MII_INTEN_UV_ERR_EN |
> >>>> \
> >>>> + MII_INTEN_UV_RECOVERY_EN | MII_INTEN_TEMP_ERR_EN |
> >>>> \
> >>>> + MII_INTEN_SLEEP_ABORT_EN)
> >>>
> >>> Why do you enable all these interrupt sources? As I said, phylib needs
> >>> link change info only.
> >>
> >> Because I need them to reliably detect that the link state changed.
Hi Marek
That statement suggests you started with just bits 10 and 9 and it
failed to detect some sort of link up/down event? What was missed?
Andrew
