On Mon, Mar 20, 2006 at 12:06:48PM +0200, Gilboa Davara wrote: > On Sun, 2006-03-19 at 18:01 +0200, Avraham Rosenberg wrote: ..
> > 3-I run smartctl on my hard disks. On the first one it failed 9 > > times ( I understand nothing of the accompanying text), but on > > the second it found nothing wrong, not even that the boot sector > > is gone (that's why I inherited it, in the first place !). Is it > > kosher that this defect was not detected ? > > Can you post the complete command line and output? > > Gilboa > > > ================================================================= > To unsubscribe, send mail to [EMAIL PROTECTED] with > the word "unsubscribe" in the message body, e.g., run the command > echo unsubscribe | mail [EMAIL PROTECTED] > Command lines: smartctl -t long /dev/hda followed some 40 minutes later by smartctl -a /dev/hda >loga Same commands for /dev/hdb. loga: smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: ST317221A Serial Number: 5EJ07GJ9 Firmware Version: 3.32 Device is: In smartctl database [for details use: -P show] ATA Version is: 5 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sat Mar 18 08:08:10 2006 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (2400) seconds. Offline data collection capabilities: (0x1d) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 26) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000c 092 079 000 Old_age Offline - 24129229 3 Spin_Up_Time 0x0002 097 097 000 Old_age Always - 0 4 Start_Stop_Count 0x0033 100 100 020 Pre-fail Always - 206 5 Reallocated_Sector_Ct 0x0033 099 099 036 Pre-fail Always - 44 7 Seek_Error_Rate 0x000d 059 050 030 Pre-fail Offline - 262043443937 9 Power_On_Hours 0x0032 063 063 000 Old_age Always - 32873 10 Spin_Retry_Count 0x0013 100 100 090 Pre-fail Always - 0 12 Power_Cycle_Count 0x0033 100 100 000 Pre-fail Always - 968 197 Current_Pending_Sector 0x0010 100 100 000 Old_age Offline - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 194 000 Old_age Always - 45 SMART Error Log Version: 1 ATA Error Count: 9 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 9 occurred at disk power-on lifetime: 32643 hours (1360 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 00 00 00 e0 00 19:20:10.344 READ DMA c8 00 08 00 00 00 e0 00 19:20:10.093 READ DMA 10 00 08 00 00 00 e0 00 19:20:10.091 RECALIBRATE [OBS-4] c8 00 08 00 00 00 e0 00 19:20:09.852 READ DMA c8 00 08 00 00 00 e0 00 19:20:09.633 READ DMA Error 8 occurred at disk power-on lifetime: 32643 hours (1360 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 00 00 00 e0 00 19:20:10.093 READ DMA 10 00 08 00 00 00 e0 00 19:20:10.091 RECALIBRATE [OBS-4] c8 00 08 00 00 00 e0 00 19:20:09.852 READ DMA c8 00 08 00 00 00 e0 00 19:20:09.633 READ DMA f8 00 01 00 00 00 e0 00 19:20:09.622 READ NATIVE MAX ADDRESS Error 7 occurred at disk power-on lifetime: 32643 hours (1360 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 00 00 00 e0 00 19:20:09.852 READ DMA c8 00 08 00 00 00 e0 00 19:20:09.633 READ DMA f8 00 01 00 00 00 e0 00 19:20:09.622 READ NATIVE MAX ADDRESS c6 00 01 00 00 00 e0 00 19:20:09.622 SET MULTIPLE MODE 10 00 01 00 00 00 e0 00 19:20:09.621 RECALIBRATE [OBS-4] Error 6 occurred at disk power-on lifetime: 32643 hours (1360 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 00 00 00 e0 00 19:20:09.633 READ DMA f8 00 01 00 00 00 e0 00 19:20:09.622 READ NATIVE MAX ADDRESS c6 00 01 00 00 00 e0 00 19:20:09.622 SET MULTIPLE MODE 10 00 01 00 00 00 e0 00 19:20:09.621 RECALIBRATE [OBS-4] 91 00 01 3f ff 3f ef 00 19:20:09.621 INITIALIZE DEVICE PARAMETERS [OBS-6] Error 5 occurred at disk power-on lifetime: 10290 hours (428 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 30 4d 06 e0 Error: ICRC, ABRT at LBA = 0x00064d30 = 412976 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 30 4d 06 e0 00 1d+00:54:38.426 READ DMA 91 00 08 01 00 00 af 00 1d+00:54:38.425 INITIALIZE DEVICE PARAMETERS [OBS-6] 00 00 08 00 00 00 00 04 1d+00:54:38.309 NOP [Abort queued commands] 91 00 08 01 00 00 af 00 1d+00:54:30.744 INITIALIZE DEVICE PARAMETERS [OBS-6] 00 00 08 00 00 00 00 04 1d+00:54:30.628 NOP [Abort queued commands] SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 32872 - # 2 Extended offline Aborted by host 90% 32863 - # 3 Extended offline Aborted by host 10% 32863 - # 4 Extended offline Aborted by host 90% 32863 - # 5 Extended offline Aborted by host 90% 32863 - Device does not support Selective Self Tests/Logging logb: smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: ST320413A Serial Number: 5ED2HRFG Firmware Version: 3.39 Device is: In smartctl database [for details use: -P show] ATA Version is: 5 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sat Mar 18 09:11:32 2006 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 422) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 23) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000e 071 057 025 Old_age Always - 119516235 3 Spin_Up_Time 0x0002 078 078 000 Old_age Always - 0 4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1865 5 Reallocated_Sector_Ct 0x0032 100 100 036 Old_age Always - 0 7 Seek_Error_Rate 0x000e 085 060 030 Old_age Always - 344581009 9 Power_On_Hours 0x0032 089 089 000 Old_age Always - 9907 10 Spin_Retry_Count 0x0012 100 100 097 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 945 194 Temperature_Celsius 0x0022 033 052 000 Old_age Always - 33 195 Hardware_ECC_Recovered 0x001a 073 057 000 Old_age Always - 219410651 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0000 100 100 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 9906 - # 2 Extended offline Completed without error 00% 9898 - Device does not support Selective Self Tests/Logging ================================================================= To unsubscribe, send mail to [EMAIL PROTECTED] with the word "unsubscribe" in the message body, e.g., run the command echo unsubscribe | mail [EMAIL PROTECTED]
