On Thu, Aug 21, 2008 at 11:44:13AM +0300, Geoff Shang wrote:
> Hello,
>
> Apologies if this is something easily solved, but I wasn't able to tur up
> any helpful pages on Google.
>
> I just started getting the folowing when I try to load up one of my
> soundcards:
>
> PCI: Assigned IRQ 11 for device 00:12.0
> IRQ routing conflict for 00:12.1, have irq 9, want irq 11
>
> As far as I can tell, nothing has changed. This system has been operating
> happily for several years. Yes it is runing an old kernel (2.4.32) but
> again nothing has changed.
Perhaps some change in BIOS settings (such as PNP settings)?
Can you try booting with knoppix?
Perhaps some hardware problem? Can you try using the cards (one at a
time) on some other machine (perhaps with knoppix)? Or at least take out
one of them at the time and see if the other works?
> 00:07.3 Bridge: Intel Corp. 82371AB PIIX4 ACPI (rev 02)
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin ? routed to IRQ 9
^^^^^
>
[snip]
>
> 00:12.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 0a)
> Subsystem: Creative Labs: Unknown device 8065
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort+
> <TAbort- <MAbort- >SERR- <PERR+
> Interrupt: pin A routed to IRQ 0
^^^^^
> Region 0: I/O ports at ec00 [size=32]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:12.1 Input device controller: Creative Labs: Unknown device 6002 (rev 0a)
> Subsystem: Creative Labs: Unknown device 0020
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop+
> ParErr+ Stepping+ SERR+ FastB2B+
> Status: Cap+ 66Mhz+ UDF+ FastB2B+ ParErr+ DEVSEL=?? >TAbort+
> <TAbort+ <MAbort+ >SERR+ <PERR+
> Latency: 0
> Interrupt: pin ? routed to IRQ 9
^^^^^
> Region 0: I/O ports at 1000 [size=8]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
Perhaps you have the output of lspci -vv from before, when all was
working well?
I do not like the 'pin ?' and the 'IRQ 0'. I do not know what they mean,
I now checked on three machines and non of them has either of these.
--
Didi
=================================================================
To unsubscribe, send mail to [EMAIL PROTECTED] with
the word "unsubscribe" in the message body, e.g., run the command
echo unsubscribe | mail [EMAIL PROTECTED]
