Hi,
I have just installed Mandrake 6.1 with kisdn-1.0.1-2-mdk6-kde-1.1.i386.rpm
and I cannot make it work.
The package isdn4utils is the one from Mandrake 6.1 (version 3.0-3mdk)
When I try to connect using kisdn I get the following in /var/log/messages:
Oct 14 21:02:27 wallaby kernel: ISDN subsystem Rev: 1.86/1.72/1.88/1.49/1.16/1.2 loaded
Oct 14 21:02:32 wallaby kernel: HiSax: Linux Driver for passive ISDN cards
Oct 14 21:02:32 wallaby kernel: HiSax: Version 3.3 (module)
Oct 14 21:02:32 wallaby kernel: HiSax: Layer1 Revision 2.34
Oct 14 21:02:32 wallaby kernel: HiSax: Layer2 Revision 2.19
Oct 14 21:02:32 wallaby kernel: HiSax: TeiMgr Revision 2.13
Oct 14 21:02:32 wallaby kernel: HiSax: Layer3 Revision 2.10
Oct 14 21:02:32 wallaby kernel: HiSax: LinkLayer Revision 2.31
Oct 14 21:02:32 wallaby kernel: HiSax: Approval certification valid
Oct 14 21:02:32 wallaby kernel: HiSax: Approved with ELSA Quickstep series cards
Oct 14 21:02:32 wallaby kernel: HiSax: Approval registration numbers:
Oct 14 21:02:32 wallaby kernel: HiSax: German D133361J CETECOM ICT Services GmbH
Oct 14 21:02:32 wallaby kernel: HiSax: EU (D133362J) CETECOM ICT Services GmbH
Oct 14 21:02:32 wallaby kernel: HiSax: Approved with Eicon Technology Diva 2.01 PCI
cards
Oct 14 21:02:32 wallaby kernel: HiSax: Card 1 Protocol EDSS1 Id=elsa_qs1000_pci (0)
Oct 14 21:02:32 wallaby kernel: HiSax: Elsa driver Rev. 2.17
Oct 14 21:02:32 wallaby kernel: Elsa: You may have a wrong PCI bios
Oct 14 21:02:32 wallaby kernel: Elsa: If your system hangs now, read
Oct 14 21:02:32 wallaby kernel: Elsa: Documentation/isdn/README.HiSax
Oct 14 21:02:32 wallaby kernel: Elsa: Waiting 5 sec to sync discs
Oct 14 21:02:32 wallaby kernel: Elsa: QS 1000 PCI defined at 0xfcec/0xfc00 IRQ 5
Oct 14 21:02:32 wallaby kernel: Elsa: IPAC version 1
Oct 14 21:02:32 wallaby kernel: Elsa PCI: IRQ 5 count 19532
Oct 14 21:02:32 wallaby kernel: Elsa PCI: IRQ 5 count 19538
Oct 14 21:02:32 wallaby kernel: HiSax: DSS1 Rev. 2.18
Oct 14 21:02:32 wallaby kernel: HiSax: 2 channels added
Oct 14 21:02:32 wallaby kernel: HiSax: MAX_WAITING_CALLS added
Oct 14 21:02:32 wallaby modprobe: can't locate module sound-slot-0
Oct 14 21:02:32 wallaby modprobe: can't locate module sound-service-0-3
Oct 14 21:02:40 wallaby ipppd: info: no PAP secret entry for this user!
Oct 14 21:02:40 wallaby ipppd[1061]: Found 1 device: /dev/ippp0
Oct 14 21:02:40 wallaby ipppd[1061]: ipppd i2.2.10 (isdn4linux version of pppd by MH)
started
Oct 14 21:02:40 wallaby ipppd[1061]: init_unit: 0
Oct 14 21:02:40 wallaby ipppd[1061]: Connect[0]: /dev/ippp0, fd: 19
Oct 14 21:02:41 wallaby kernel: ippp0: dialing 1 08450798054...
Oct 14 21:02:43 wallaby kernel: isdn_net: ippp0 connected
Oct 14 21:02:43 wallaby ipppd[1061]: Local number: , Remote number: 08450798054, Type:
outgoing
Oct 14 21:02:43 wallaby ipppd[1061]: PHASE_WAIT -> PHASE_ESTABLISHED, ifunit: 0,
linkunit: 0, fd: 19
At this stage there is a lot of traffic happening but no dynamic IP (IP of local and
IP of remote) have been allocated.
note: ppp support is compiled as module in the default Mandrake 6.1 kernel 2.2.13
#ifconfig ippp0 shows:
ippp0 Link encap:Point-to-Point Protocol
inet addr:1.1.1.1 P-t-P:1.1.1.1 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MTU:1500 Metric:1
RX packets:4603 errors:0 dropped:0 overruns:0 frame:0
TX packets:4602 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:30
#route -n shows:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo
#isdnctrl list ippp0
Current setup of interface 'ippp0':
EAZ/MSN:
Phone number(s):
Outgoing: 08450798054
Incoming:
Dial mode: auto
Secure: on
Callback: off
Reject before Callback: on
Callback-delay: 5
Dialmax: 1
Hangup-Timeout: 600
Incoming-Hangup: on
ChargeHangup: off
Charge-Units: 0
Charge-Interval: 0
Layer-2-Protocol: hdlc
Layer-3-Protocol: trans
Encapsulation: syncppp
Slave Interface: None
Slave delay: 10
Slave trigger: 6000 cps
Master Interface: None
Pre-Bound to: Nothing
PPP-Bound to: Nothing
** Some of my config files **
/etc/host.conf
order hosts bind
multi on
/etc/networks
loopback 127.0.0.0
primex 195.112.4.0 <- my ISP
/etc/route.conf
195.112.4.0 0.0.0.0 255.255.255.0 ippp0
default 195.112.4.11
/etc/resolv.conf
search primex.co.uk
nameserver 195.112.4.4
nameserver 195.112.4.7
/etc/hosts
127.0.0.1 localhost
192.168.0.99 wallaby.primex.co.uk wallaby
195.112.4.11 primex
Any help much appreciated.
Cheers,
Fred
/////
( / \ )
( O O )
______________________oOOo-( )-oOOo_______________________
Frederic Soulier
private e-mail: [EMAIL PROTECTED]
office e-mail: [EMAIL PROTECTED]
office tel: +44 (0)20 856 20959
______________________________Oooo________________________
oooO ( )
( ) ) /
\ ( (_/
\_)
