On Wed, Jan 20, 2016 at 01:23:39PM +0100, Lothar Waßmann wrote:
> The TX51-8xxx module series is a System On Module manufactured by
> Ka-Ro electronics GmbH with the following characteristics:
> Processor Freescale i.MX515
> up to 800 MHz (commercial)
> up to 600 MHz (industrial)
> RAM 128/256MB mobile DDR-SDRAM
> ROM 128MB NAND Flash
> RTC DS1339 Real Time Clock
> Power supply Single 3.1V to 5.5V
> Size 26mm SO-DIMM
> Temp. Range 0°C..70°C (-40°C..85°C)
>
> Signed-off-by: Lothar Waßmann <l...@karo-electronics.de>
> ---
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/imx51-tx51.dts | 749
> +++++++++++++++++++++++++++++++++++++++
> 2 files changed, 751 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/imx51-tx51.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index a4a6d70..ea70f34 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -277,7 +277,8 @@ dtb-$(CONFIG_SOC_IMX51) += \
> imx51-babbage.dtb \
> imx51-digi-connectcore-jsk.dtb \
> imx51-eukrea-mbimxsd51-baseboard.dtb \
> - imx51-ts4800.dtb
> + imx51-ts4800.dtb \
> + imx51-tx51.dtb
> dtb-$(CONFIG_SOC_IMX53) += \
> imx53-ard.dtb \
> imx53-m53evk.dtb \
> diff --git a/arch/arm/boot/dts/imx51-tx51.dts
> b/arch/arm/boot/dts/imx51-tx51.dts
> new file mode 100644
> index 0000000..80c5d60
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx51-tx51.dts
> @@ -0,0 +1,749 @@
> +/*
> + * Copyright 2012-2014 Lothar Waßmann <l...@karo-electronics.de>
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
We generally suggest GPL/X11 dual license for new dts to consider
non-Linux device tree users.
> +
> +/dts-v1/;
> +#include "imx51.dtsi"
> +#include <dt-bindings/pwm/pwm.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> + model = "Ka-Ro electronics TX51 module";
> + compatible = "karo,tx51", "fsl,imx51";
> +
> + aliases {
> + backlight = &backlight;
> + display = &display;
> + i2c1 = &i2c_gpio;
> + usbotg = &usbotg;
> + wlan0 = &wlan0;
> + };
> +
> + chosen {
> + stdout-path = &uart1;
> + };
> +
> + backlight: pwm-backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
> + power-supply = <®_3v3>;
> + brightness-levels = <
> + 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100
> + >;
> + default-brightness-level = <50>;
> + };
> +
> + clocks {
> + ckih1 {
> + clock-frequency = <0>;
> + };
> +
> + mclk: clock@0 {
I would like to see these fixed rate clocks are named in a consistent
way, maybe just drop 'reg' property and use a unique clock name to align
with what imx51.dtsi does.
> + compatible = "fixed-clock";
> + reg = <0>;
> + #clock-cells = <0>;
> + clock-output-names = "mclk";
> + clock-frequency = <26000000>;
> + };
> +
> + clk_26M: clock@1 {
> + compatible = "fixed-clock";
> + reg = <1>;
> + #clock-cells = <0>;
> + clock-output-names = "clk_26M";
> + clock-frequency = <26000000>;
> + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
> + };
> +
> + wlan_ref_clk: wlan-ref-clk {
> + compatible = "ti,wilink-clock";
I do not see this compatible string is documented anywhere. And how is
this compatible string used by kernel?
> + #clock-cells = <0>;
> + clock-frequency = <38400000>;
> + };
> + };
> +
> + display: display@di0 {
> + compatible = "fsl,imx-parallel-display";
> + interface-pix-fmt = "rgb24";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ipu_disp0>;
> +
> + display-timings {
> + VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hsync-len = <96>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vsync-len = <2>;
> + vfront-porch = <12>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETV570 {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <114>;
> + hsync-len = <30>;
> + hfront-porch = <16>;
> + vback-porch = <32>;
> + vsync-len = <3>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0350 {
> + clock-frequency = <6413760>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <34>;
> + hsync-len = <34>;
> + hfront-porch = <20>;
> + vback-porch = <15>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0430 {
> + clock-frequency = <9009000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <2>;
> + hsync-len = <41>;
> + hfront-porch = <2>;
> + vback-porch = <2>;
> + vsync-len = <10>;
> + vfront-porch = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0500 {
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0700 { /* same as ET0500 */
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETQ570 {
> + clock-frequency = <6596040>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <38>;
> + hsync-len = <30>;
> + hfront-porch = <30>;
> + vback-porch = <16>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> +
> + port {
> + display0_in: endpoint {
> + remote-endpoint = <&ipu_di0_disp0>;
> + };
> + };
> + };
> +
> + i2c_gpio: i2c-gpio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "i2c-gpio";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c_gpio>;
> + gpios = <&gpio4 17 0
> + &gpio4 16 0>;
> + clock-frequency = <400000>;
> +
> + rtc1: ds1339@68 {
> + compatible = "dallas,ds1339";
> + reg = <0x68>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_stk5led>;
> +
> + user {
> + label = "Heartbeat";
> + gpios = <&gpio4 10 0 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + reg_2v5: regulator@0 {
Device tree maintainers do not like the fake simple-bus container node.
We are asked to put these fixed regulators directly under root node,
with a unique node name like:
reg_xxx: regulator-xxx {
...
};
> + compatible = "regulator-fixed";
> + reg = <0>;
> + regulator-name = "2V5";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + regulator-always-on;
> + };
> +
> + reg_3v3: regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reg_etn_phy: regulator@2 {
> + compatible = "regulator-fixed";
> + reg = <2>;
> + regulator-name = "ETN PHY Power";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_lcd_pwr: regulator@5 {
> + compatible = "regulator-fixed";
> + reg = <5>;
> + regulator-name = "LCD POWER";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio4 14 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_lcd_reset: regulator@6 {
> + compatible = "regulator-fixed";
> + reg = <6>;
> + regulator-name = "LCD RESET";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd_reset>;
> + gpio = <&gpio4 13 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_wlan0: regulator@9 {
> + compatible = "regulator-fixed";
> + reg = <8>;
> + regulator-name = "wlan0";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> + };
> +
> + sound {
> + compatible = "karo,tx51-audio-sgtl5000",
> "fsl,imx-audio-sgtl5000";
> + model = "tx51-audio-sgtl5000";
> + ssi-controller = <&ssi1>;
> + audio-codec = <&sgtl5000>;
> + audio-routing =
> + "MIC_IN", "Mic Jack",
> + "Mic Jack", "Mic Bias",
> + "Headphone Jack", "HP_OUT";
> + /* '1' based port numbers according to datasheet names */
> + mux-int-port = <1>;
> + mux-ext-port = <3>;
> + };
> +
> + usbphy {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "simple-bus";
> +
> + usbh1phy: usbphy@0 {
> + compatible = "usb-nop-xceiv";
> + reg = <0>;
> + clocks = <&clk_26M>;
> + clock-names = "main_clk";
> + };
This should probably go with the same way as fixed regulators.
> + };
> +
> + wlan0: tiwi-ble {
> + compatible = "ti,wilink6";
Undocumented compatible string.
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wlan0>;
> + clocks = <&wlan_ref_clk>;
> + clock-names = "refclock";
> + interrupt-parent = <&gpio1>;
> + interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> +
> +&audmux {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ssi1>;
> + status = "okay";
> +};
> +
> +&ecspi1 {
> + fsl,spi-num-chipselects = <2>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi1>;
> + cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>,
> + <&gpio4 25 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +
> + spidev0: spi@0 {
> + compatible = "spidev";
> + reg = <0>;
> + spi-max-frequency = <54000000>;
> + };
> +
> + spidev1: spi@1 {
> + compatible = "spidev";
> + reg = <1>;
> + spi-max-frequency = <54000000>;
> + };
> +};
> +
> +&esdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_esdhc1>;
> + cd-gpios = <&gpio3 8 GPIO_ACTIVE_LOW>;
> + fsl,wp-controller;
> + status = "okay";
> +};
> +
> +&esdhc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_esdhc2 &pinctrl_wlan0>;
> + vmmc-supply = <®_wlan0>;
> + bus-width = <4>;
> + no-1-8-v;
> + fsl,wp-controller;
> + cap-sdio-irq;
> + non-removable;
> + //cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
Drop it.
> + status = "okay";
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec>;
> + phy-mode = "mii";
> +// phy-handle = <&phy0>;
> + local-mac-address = [000000000000]; /* will be set by U-Boot */
> + status = "okay";
> +
> + phy0: ethernet-phy@0 {
> + interrupt-parent = <&gpio3>;
> + interrupts = <18 0>;
> + device_type = "ethernet-phy";
> + };
This probably works, but I think we should follow the more standard
bindings to put it like the following?
phy-handle = <&phy0>;
mdio {
#address-cells = <1>;
#size-cells = <0>;
phy0: ethernet-phy@0 {
interrupt-parent = <&gpio3>;
interrupts = <18 0>;
device_type = "ethernet-phy";
};
};
> +};
> +
> +&ipu {
> + status = "okay";
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +
> + sgtl5000: sgtl5000@0a {
Use generic name like 'codec' for node might comply to DT convention
better.
> + compatible = "fsl,sgtl5000";
> + reg = <0x0a>;
> + clocks = <&mclk>;
> + VDDA-supply = <®_2v5>;
> + VDDIO-supply = <®_3v3>;
> + };
> +
> + polytouch: edt-ft5x06@38 {
> + compatible = "edt,edt-ft5x06";
> + reg = <0x38>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_edt_ft5x06>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <5 0>;
> + reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
> + wake-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>;
> + };
> +
> + touchscreen: tsc2007@48 {
tsc2007: touchscreen@48 {
> + compatible = "ti,tsc2007";
> + reg = <0x48>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_tsc2007>;
> + interrupt-parent = <&gpio3>;
> + interrupts = <3 0>;
> + gpios = <&gpio3 3 GPIO_ACTIVE_LOW>;
> + ti,x-plate-ohms = <660>;
> + linux,wakeup;
Use the new standard 'wakeup-source' please.
https://git.kernel.org/cgit/linux/kernel/git/shawnguo/linux.git/commit/?h=imx/dt&id=1c49ad21c2cae607193da4495489c751d7147df2
> + };
> +};
> +
> +&iomuxc {
Please move the node to the bottom of the file to make the reset a bit
easier for reading.
> + imx51-tx51 {
Since commit 5fcdf6a7ed95 (pinctrl: imx: Allow parsing DT without
function nodes), this additional function container node can be saved.
> + pinctrl_hog: hoggrp {
> + fsl,pins = <
> + MX51_PAD_GPIO1_7__GPIO1_7 0x20e0
> /* 26MHz osc enable */
> + >;
> + };
> +
> + pinctrl_ecspi1: ecspi1grp {
> + fsl,pins = <
> + MX51_PAD_CSPI1_SS0__ECSPI1_SS0 0x4
> + MX51_PAD_CSPI1_SS1__ECSPI1_SS1 0x4
> + MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK 0x5
> + MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI 0x85
> + MX51_PAD_CSPI1_MISO__ECSPI1_MISO 0x185
> + MX51_PAD_CSPI1_RDY__ECSPI1_RDY 0x84
> + >;
> + };
> +
> + pinctrl_edt_ft5x06: edt-ft5x056grp {
I would suggest to not use any hyphen in pinctrl group node name to make
the naming looks more consistent.
> + fsl,pins = <
> + MX51_PAD_GPIO1_5__GPIO1_5 0x20e0
> /* Interrupt */
> + MX51_PAD_CSI2_PIXCLK__GPIO4_15 0x20e0
> /* Reset */
> + MX51_PAD_CSI2_D12__GPIO4_9 0x20e0
> /* Wake */
> + >;
> + };
> +
> + pinctrl_esdhc1: esdhc1grp {
> + fsl,pins = <
> + MX51_PAD_DISPB2_SER_RS__GPIO3_8 0x1c0
> /* SD1 CD */
> + MX51_PAD_SD1_DATA0__SD1_DATA0 0x20d4
> + MX51_PAD_SD1_DATA1__SD1_DATA1 0x20d4
> + MX51_PAD_SD1_DATA2__SD1_DATA2 0x20d4
> + MX51_PAD_SD1_DATA3__SD1_DATA3 0x20d4
> + MX51_PAD_SD1_CMD__SD1_CMD
> 0x400020d4
> + MX51_PAD_SD1_CLK__SD1_CLK 0x2004
> + >;
> + };
> +
> + pinctrl_esdhc2: esdhc2grp {
> + fsl,pins = <
> + MX51_PAD_DISPB2_SER_DIO__GPIO3_6 0x1c0
> /* SD2 CD */
> + MX51_PAD_SD2_DATA0__SD2_DATA0 0x20d4
> + MX51_PAD_SD2_DATA1__SD2_DATA1 0x20d4
> + MX51_PAD_SD2_DATA2__SD2_DATA2 0x20d4
> + MX51_PAD_SD2_DATA3__SD2_DATA3 0x20d4
> + MX51_PAD_SD2_CMD__SD2_CMD
> 0x400020d4
> + MX51_PAD_SD2_CLK__SD2_CLK 0x2004
> + >;
> + };
> +
> + pinctrl_fec: fecgrp {
> + fsl,pins = <
> + MX51_PAD_EIM_A20__GPIO2_14 0x20e4
> /* PHY reset */
> + MX51_PAD_GPIO1_3__GPIO1_3 0x20e4
> /* PHY power */
> + MX51_PAD_NANDF_CS3__FEC_MDC 0x2004
> + MX51_PAD_EIM_EB2__FEC_MDIO 0x0005
> + MX51_PAD_NANDF_RB3__FEC_RX_CLK 0x2000
> + MX51_PAD_NANDF_D11__FEC_RX_DV 0x2000
> + MX51_PAD_NANDF_D9__FEC_RDATA0 0x2000
> + MX51_PAD_EIM_EB3__FEC_RDATA1 0x0001
> + MX51_PAD_EIM_CS2__FEC_RDATA2 0x0001
> + MX51_PAD_EIM_CS3__FEC_RDATA3 0x0001
> + MX51_PAD_EIM_CS4__FEC_RX_ER 0x0001
> + MX51_PAD_NANDF_RDY_INT__FEC_TX_CLK 0x2000
> + MX51_PAD_NANDF_CS7__FEC_TX_EN 0x2004
> + MX51_PAD_NANDF_D8__FEC_TDATA0 0x2004
> + MX51_PAD_NANDF_CS4__FEC_TDATA1 0x2004
> + MX51_PAD_NANDF_CS5__FEC_TDATA2 0x2004
> + MX51_PAD_NANDF_CS6__FEC_TDATA3 0x2004
> + MX51_PAD_NANDF_RB2__FEC_COL 0x2000
> + MX51_PAD_EIM_CS5__FEC_CRS 0x0005
> + MX51_PAD_NANDF_CS2__GPIO3_18 0x20e4
> + >;
> + };
> +
> + pinctrl_i2c2: ipu-i2c2grp {
> + fsl,pins = <
> + MX51_PAD_EIM_D27__I2C2_SCL
> 0x40000004
> + MX51_PAD_EIM_D24__I2C2_SDA
> 0x40000004
> + >;
> + };
> +
> + pinctrl_i2c_gpio: ipu-i2c-gpiogrp {
> + fsl,pins = <
> + MX51_PAD_I2C1_CLK__GPIO4_16
> 0x40000004
> + MX51_PAD_I2C1_DAT__GPIO4_17
> 0x40000004
> + >;
> + };
> +
> + pinctrl_ipu_disp0: ipu-disp0grp {
> + fsl,pins = <
> + MX51_PAD_DISP1_DAT0__DISP1_DAT0 0x5
> + MX51_PAD_DISP1_DAT1__DISP1_DAT1 0x5
> + MX51_PAD_DISP1_DAT2__DISP1_DAT2 0x5
> + MX51_PAD_DISP1_DAT3__DISP1_DAT3 0x5
> + MX51_PAD_DISP1_DAT4__DISP1_DAT4 0x5
> + MX51_PAD_DISP1_DAT5__DISP1_DAT5 0x5
> + MX51_PAD_DISP1_DAT6__DISP1_DAT6 0x5
> + MX51_PAD_DISP1_DAT7__DISP1_DAT7 0x5
> + MX51_PAD_DISP1_DAT8__DISP1_DAT8 0x5
> + MX51_PAD_DISP1_DAT9__DISP1_DAT9 0x5
> + MX51_PAD_DISP1_DAT10__DISP1_DAT10 0x5
> + MX51_PAD_DISP1_DAT11__DISP1_DAT11 0x5
> + MX51_PAD_DISP1_DAT12__DISP1_DAT12 0x5
> + MX51_PAD_DISP1_DAT13__DISP1_DAT13 0x5
> + MX51_PAD_DISP1_DAT14__DISP1_DAT14 0x5
> + MX51_PAD_DISP1_DAT15__DISP1_DAT15 0x5
> + MX51_PAD_DISP1_DAT16__DISP1_DAT16 0x5
> + MX51_PAD_DISP1_DAT17__DISP1_DAT17 0x5
> + MX51_PAD_DISP1_DAT18__DISP1_DAT18 0x5
> + MX51_PAD_DISP1_DAT19__DISP1_DAT19 0x5
> + MX51_PAD_DISP1_DAT20__DISP1_DAT20 0x5
> + MX51_PAD_DISP1_DAT21__DISP1_DAT21 0x5
> + MX51_PAD_DISP1_DAT22__DISP1_DAT22 0x5
> + MX51_PAD_DISP1_DAT23__DISP1_DAT23 0x5
> + MX51_PAD_DI1_PIN2__DI1_PIN2 0x5 /*
> HSYNC */
> + MX51_PAD_DI1_PIN3__DI1_PIN3 0x5 /*
> VSYNC */
> + >;
> + };
> +
> + pinctrl_kpp: kppgrp-1 {
The '-1' suffix means nothing and can just be dropped.
> + fsl,pins = <
> + MX51_PAD_KEY_ROW0__KEY_ROW0 0xe0
> + MX51_PAD_KEY_ROW1__KEY_ROW1 0xe0
> + MX51_PAD_KEY_ROW2__KEY_ROW2 0xe0
> + MX51_PAD_KEY_ROW3__KEY_ROW3 0xe0
> + MX51_PAD_KEY_COL0__KEY_COL0 0xe8
> + MX51_PAD_KEY_COL1__KEY_COL1 0xe8
> + MX51_PAD_KEY_COL2__KEY_COL2 0xe8
> + MX51_PAD_KEY_COL3__KEY_COL3 0xe8
> + MX51_PAD_KEY_COL4__KEY_COL4 0xe8
> + MX51_PAD_KEY_COL5__KEY_COL5 0xe8
> + >;
> + };
> +
> + pinctrl_lcd_pwr: lcd-pwrgrp {
> + fsl,pins = <
> + MX51_PAD_CSI2_HSYNC__GPIO4_14 0x4
> + >;
> + };
> +
> + pinctrl_lcd_reset: lcd-resetgrp {
> + fsl,pins = <
> + MX51_PAD_CSI2_VSYNC__GPIO4_13 0x4
> + >;
> + };
> +
> + pinctrl_pwm1: pwm1grp {
> + fsl,pins = <
> + MX51_PAD_GPIO1_2__PWM1_PWMO 0xf4
> + >;
> + };
> +
> + pinctrl_ssi1: ssi1grp {
> + fsl,pins = <
> + MX51_PAD_AUD3_BB_RXD__AUD3_RXD 0x5
> + MX51_PAD_AUD3_BB_TXD__AUD3_TXD 0x5
> + MX51_PAD_AUD3_BB_CK__AUD3_TXC 0x5
> + MX51_PAD_AUD3_BB_FS__AUD3_TXFS 0x5
> + >;
> + };
> +
> + pinctrl_ssi2: ssi2grp {
> + fsl,pins = <
> + MX51_PAD_EIM_D29__AUD6_RXD 0x5
> + MX51_PAD_EIM_D28__AUD6_TXD 0x5
> + MX51_PAD_EIM_D30__AUD6_TXC 0x5
> + MX51_PAD_EIM_D31__AUD6_TXFS 0x5
> + >;
> + };
> +
> + pinctrl_stk5led: stk5ledgrp {
> + fsl,pins = <
> + MX51_PAD_CSI2_D13__GPIO4_10 0x20e4
> + >;
> + };
> +
> + pinctrl_tsc2007: tsc2007grp {
> + fsl,pins = <
> + MX51_PAD_DI1_D0_CS__GPIO3_3 0xc0
> /* Pen-Down Interrupt */
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX51_PAD_UART1_RXD__UART1_RXD 0xc1
> + MX51_PAD_UART1_TXD__UART1_TXD 0xc5
> + MX51_PAD_UART1_RTS__UART1_RTS 0xc1
> + MX51_PAD_UART1_CTS__UART1_CTS 0xc5
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX51_PAD_UART2_RXD__UART2_RXD 0xc1
> + MX51_PAD_UART2_TXD__UART2_TXD 0xc5
> + MX51_PAD_EIM_D26__UART2_RTS 0xc1
> + MX51_PAD_EIM_D25__UART2_CTS 0xc5
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX51_PAD_UART3_RXD__UART3_RXD 0xc1
> + MX51_PAD_UART3_TXD__UART3_TXD 0xc5
> + MX51_PAD_EIM_D18__UART3_RTS 0xc1
> + MX51_PAD_EIM_D17__UART3_CTS 0xc5
> + >;
> + };
> +
> + pinctrl_wlan0: wlan0grp {
> + fsl,pins = <
> + MX51_PAD_CSI2_PIXCLK__GPIO4_15 0x04 /*
> WL_EN */
> + MX51_PAD_GPIO1_5__GPIO1_5 0xf0 /*
> WL_IRQ */
> + >;
> + };
> + };
> +};
> +
> +&ipu_di0_disp0 {
> + remote-endpoint = <&display0_in>;
> +};
> +
> +&kpp {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_kpp>;
> + linux,keymap = < /* sample keymap */
> + MATRIX_KEY(0, 0, KEY_POWER)
> + MATRIX_KEY(0, 1, KEY_KP0)
> + MATRIX_KEY(0, 2, KEY_KP1)
> + MATRIX_KEY(0, 3, KEY_KP2)
> + MATRIX_KEY(1, 0, KEY_KP3)
> + MATRIX_KEY(1, 1, KEY_KP4)
> + MATRIX_KEY(1, 2, KEY_KP5)
> + MATRIX_KEY(1, 3, KEY_KP6)
> + MATRIX_KEY(2, 0, KEY_KP7)
> + MATRIX_KEY(2, 1, KEY_KP8)
> + MATRIX_KEY(2, 2, KEY_KP9)
> + >;
> + status = "okay";
> +};
> +
> +&nfc {
> + nand-bus-width = <8>;
> + nand-ecc-mode = "hw";
> + nand-on-flash-bbt;
> + status = "okay";
> +};
> +
> +&pwm1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm1>;
> +};
> +
> +&ssi1 {
> + fsl,mode = "i2s-slave";
The "i2s-slave" of fsl,mode is deprecated and can be dropped.
Shawn
> + codec-handle = <&sgtl5000>;
> + status = "okay";
> +};
> +
> +&ssi2 {
> + status = "disabled";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + fsl,uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + fsl,uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart3>;
> + fsl,uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&usbh1 {
> + phy_type = "ulpi";
> + fsl,usphy = <&usbh1phy>;
> + disable-over-current;
> + status = "okay";
> +};
> +
> +&usbotg {
> + dr_mode = "peripheral";
> + phy_type = "utmi_wide";
> + disable-over-current;
> + status = "okay";
> +};
> --
> 2.1.4
>
>
