From: Stefan Agner <ste...@agner.ch>
In order to allow wake support in STOP sleep mode, clocks are
needed. Use imx_clk_gate2_cgr to disable automatic clock gating
in low power mode STOP. This allows to enable wake by UART using:
echo enabled > /sys/class/tty/ttyLP0/power/wakeup
However, if wake is not enabled, the driver should disable the
clocks explicitly to save power.
Signed-off-by: Stefan Agner <ste...@agner.ch>
---
drivers/clk/imx/clk-vf610.c | 12 ++++++------
drivers/tty/serial/fsl_lpuart.c | 16 ++++++++++++++--
2 files changed, 20 insertions(+), 8 deletions(-)
diff --git a/drivers/clk/imx/clk-vf610.c b/drivers/clk/imx/clk-vf610.c
index 3a1f244..0476353 100644
--- a/drivers/clk/imx/clk-vf610.c
+++ b/drivers/clk/imx/clk-vf610.c
@@ -315,12 +315,12 @@ static void __init vf610_clocks_init(struct device_node
*ccm_node)
clk[VF610_CLK_PIT] = imx_clk_gate2("pit", "ipg_bus", CCM_CCGR1,
CCM_CCGRx_CGn(7));
- clk[VF610_CLK_UART0] = imx_clk_gate2("uart0", "ipg_bus", CCM_CCGR0,
CCM_CCGRx_CGn(7));
- clk[VF610_CLK_UART1] = imx_clk_gate2("uart1", "ipg_bus", CCM_CCGR0,
CCM_CCGRx_CGn(8));
- clk[VF610_CLK_UART2] = imx_clk_gate2("uart2", "ipg_bus", CCM_CCGR0,
CCM_CCGRx_CGn(9));
- clk[VF610_CLK_UART3] = imx_clk_gate2("uart3", "ipg_bus", CCM_CCGR0,
CCM_CCGRx_CGn(10));
- clk[VF610_CLK_UART4] = imx_clk_gate2("uart4", "ipg_bus", CCM_CCGR6,
CCM_CCGRx_CGn(9));
- clk[VF610_CLK_UART5] = imx_clk_gate2("uart5", "ipg_bus", CCM_CCGR6,
CCM_CCGRx_CGn(10));
+ clk[VF610_CLK_UART0] = imx_clk_gate2_cgr("uart0", "ipg_bus", CCM_CCGR0,
CCM_CCGRx_CGn(7), 0x2);
+ clk[VF610_CLK_UART1] = imx_clk_gate2_cgr("uart1", "ipg_bus", CCM_CCGR0,
CCM_CCGRx_CGn(8), 0x2);
+ clk[VF610_CLK_UART2] = imx_clk_gate2_cgr("uart2", "ipg_bus", CCM_CCGR0,
CCM_CCGRx_CGn(9), 0x2);
+ clk[VF610_CLK_UART3] = imx_clk_gate2_cgr("uart3", "ipg_bus", CCM_CCGR0,
CCM_CCGRx_CGn(10), 0x2);
+ clk[VF610_CLK_UART4] = imx_clk_gate2_cgr("uart4", "ipg_bus", CCM_CCGR6,
CCM_CCGRx_CGn(9), 0x2);
+ clk[VF610_CLK_UART5] = imx_clk_gate2_cgr("uart5", "ipg_bus", CCM_CCGR6,
CCM_CCGRx_CGn(10), 0x2);
clk[VF610_CLK_I2C0] = imx_clk_gate2("i2c0", "ipg_bus", CCM_CCGR4,
CCM_CCGRx_CGn(6));
clk[VF610_CLK_I2C1] = imx_clk_gate2("i2c1", "ipg_bus", CCM_CCGR4,
CCM_CCGRx_CGn(7));
diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index fabfa7e..75a2098 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -483,9 +483,8 @@ static void lpuart_dma_rx_complete(void *arg)
spin_unlock_irqrestore(&sport->port.lock, flags);
}
-static void lpuart_timer_func(unsigned long data)
+static void lpuart_dma_rx_terminate(struct lpuart_port *sport)
{
- struct lpuart_port *sport = (struct lpuart_port *)data;
struct tty_port *port = &sport->port.state->port;
struct dma_tx_state state;
unsigned long flags;
@@ -510,6 +509,11 @@ static void lpuart_timer_func(unsigned long data)
spin_unlock_irqrestore(&sport->port.lock, flags);
}
+static void lpuart_timer_func(unsigned long data)
+{
+ lpuart_dma_rx_terminate((struct lpuart_port *)data);
+}
+
static inline void lpuart_prepare_rx(struct lpuart_port *sport)
{
unsigned long flags;
@@ -1925,7 +1929,12 @@ static int lpuart_suspend(struct device *dev)
writeb(temp, sport->port.membase + UARTCR2);
}
+ if (sport->dma_rx_in_progress)
+ lpuart_dma_rx_terminate(sport);
+
uart_suspend_port(&lpuart_reg, &sport->port);
+ if (sport->port.suspended && !sport->port.irq_wake)
+ clk_disable_unprepare(sport->clk);
return 0;
}
@@ -1935,6 +1944,9 @@ static int lpuart_resume(struct device *dev)
struct lpuart_port *sport = dev_get_drvdata(dev);
unsigned long temp;
+ if (sport->port.suspended && !sport->port.irq_wake)
+ clk_prepare_enable(sport->clk);
+
if (sport->lpuart32) {
lpuart32_setup_watermark(sport);
temp = lpuart32_read(sport->port.membase + UARTCTRL);
--
2.8.3
