Hi Vadim, Please use git format-patch -n, where n is the number of patches to be produced starting from your current git HEAD.
It will produce patches tagged [PATCH 1/2], [PATCH 2/2], or starting from [PATCH 0/2] when added --cover-letter switch. Now it looks as if this patch was a part of the patch set comprising two patches, but I don't see the first one. I assume that you added the numbering by hand and this one was intended to be put in the one set with the following one: [patch] leds: add driver for Mellanox systems leds On 09/07/2016 04:53 PM, [email protected] wrote:
From: Vadim Pasternak <[email protected]> Fix in comments 3KHz and 6KHz to 3Hz and 6Hz respectively. Signed-off-by: Vadim Pasternak <[email protected]> --- drivers/leds/leds-mlxcpld.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/drivers/leds/leds-mlxcpld.c b/drivers/leds/leds-mlxcpld.c index 0ec2375..eeed35c 100644 --- a/drivers/leds/leds-mlxcpld.c +++ b/drivers/leds/leds-mlxcpld.c @@ -47,8 +47,8 @@ #define MLXPLAT_CPLD_LPC_REG_BASE_ADRR 0x2500 /* LPC bus access */ /* Color codes for leds */ -#define LED_OFFSET_HALF 0x01 /* Offset from solid for 3KHz blink */ -#define LED_OFFSET_FULL 0x02 /* Offset from solid for 6KHz blink */ +#define LED_OFFSET_HALF 0x01 /* Offset from solid for 3Hz blink */ +#define LED_OFFSET_FULL 0x02 /* Offset from solid for 6Hz blink */ #define LED_IS_OFF 0x00 /* Off */ #define LED_RED_STATIC_ON 0x05 /* Solid red */ #define LED_RED_BLINK_HALF (LED_RED_STATIC_ON + LED_OFFSET_HALF) @@ -237,7 +237,7 @@ static void mlxcpld_led_store_hw(u8 mask, u8 off, u8 vset) /* Each led is controlled through low or high nibble of the relevant * CPLD register. Register offset is specified by off parameter. * Parameter vset provides color code: 0x0 for off, 0x5 for solid red, - * 0x6 for 3KHz blink red, 0xd for solid green, 0xe for 3KHz blink + * 0x6 for 3Hz blink red, 0xd for solid green, 0xe for 3Hz blink * green. * Parameter mask specifies which nibble is used for specific led: mask * 0xf0 - lower nibble is to be used (bits from 0 to 3), mask 0x0f - @@ -274,8 +274,8 @@ static int mlxcpld_led_blink(struct led_classdev *led, { struct mlxcpld_led_priv *pled = cdev_to_priv(led); - /* HW supports two types of blinking: full (6KHz) and half (3KHz). - * For delay on/off zero default setting 3KHz is used. + /* HW supports two types of blinking: full (6Hz) and half (3Hz). + * For delay on/off zero default setting 3Hz is used. */ if (!(*delay_on == 0 && *delay_off == 0) && !(*delay_on == LED_BLINK_3HZ && *delay_off == LED_BLINK_3HZ) &&
-- Best regards, Jacek Anaszewski
