Hi Jacek, The patch 2/2 I sent after Dave's review. Now I have patch 1/2 and patch 2/2, produced with git format-patch -2 HEAD ... But 1/2 is re-work after your comments.
Would it be OK if I produce now new patch with all fixes as [patch v1], and starting from this point will follow [patch v2], etc? Sorry for this mess. Thanks, Vadim. > -----Original Message----- > From: Jacek Anaszewski [mailto:[email protected]] > Sent: Wednesday, September 07, 2016 4:11 PM > To: Vadim Pasternak <[email protected]>; [email protected] > Cc: [email protected]; [email protected]; > [email protected]; > Michael Shych <[email protected]> > Subject: Re: [patch 2/2] leds: add driver for Mellanox systems leds > > Hi Vadim, > > Please use git format-patch -n, where n is the number of patches to be > produced > starting from your current git HEAD. > > It will produce patches tagged [PATCH 1/2], [PATCH 2/2], or starting from > [PATCH 0/2] when added --cover-letter switch. > > Now it looks as if this patch was a part of the patch set comprising two > patches, > but I don't see the first one. > I assume that you added the numbering by hand and this one was intended to be > put in the one set with the following one: > > [patch] leds: add driver for Mellanox systems leds > > On 09/07/2016 04:53 PM, [email protected] wrote: > > From: Vadim Pasternak <[email protected]> > > > > Fix in comments 3KHz and 6KHz to 3Hz and 6Hz respectively. > > > > Signed-off-by: Vadim Pasternak <[email protected]> > > --- > > drivers/leds/leds-mlxcpld.c | 10 +++++----- > > 1 file changed, 5 insertions(+), 5 deletions(-) > > > > diff --git a/drivers/leds/leds-mlxcpld.c b/drivers/leds/leds-mlxcpld.c > > index 0ec2375..eeed35c 100644 > > --- a/drivers/leds/leds-mlxcpld.c > > +++ b/drivers/leds/leds-mlxcpld.c > > @@ -47,8 +47,8 @@ > > #define MLXPLAT_CPLD_LPC_REG_BASE_ADRR 0x2500 /* LPC bus access */ > > > > /* Color codes for leds */ > > -#define LED_OFFSET_HALF 0x01 /* Offset from solid for 3KHz blink > */ > > -#define LED_OFFSET_FULL 0x02 /* Offset from solid for 6KHz blink > */ > > +#define LED_OFFSET_HALF 0x01 /* Offset from solid for 3Hz blink > */ > > +#define LED_OFFSET_FULL 0x02 /* Offset from solid for 6Hz blink > */ > > #define LED_IS_OFF 0x00 /* Off */ > > #define LED_RED_STATIC_ON 0x05 /* Solid red */ > > #define LED_RED_BLINK_HALF (LED_RED_STATIC_ON + > LED_OFFSET_HALF) > > @@ -237,7 +237,7 @@ static void mlxcpld_led_store_hw(u8 mask, u8 off, u8 > vset) > > /* Each led is controlled through low or high nibble of the relevant > > * CPLD register. Register offset is specified by off parameter. > > * Parameter vset provides color code: 0x0 for off, 0x5 for solid red, > > - * 0x6 for 3KHz blink red, 0xd for solid green, 0xe for 3KHz blink > > + * 0x6 for 3Hz blink red, 0xd for solid green, 0xe for 3Hz blink > > * green. > > * Parameter mask specifies which nibble is used for specific led: mask > > * 0xf0 - lower nibble is to be used (bits from 0 to 3), mask 0x0f - > > @@ -274,8 +274,8 @@ static int mlxcpld_led_blink(struct led_classdev > > *led, { > > struct mlxcpld_led_priv *pled = cdev_to_priv(led); > > > > - /* HW supports two types of blinking: full (6KHz) and half (3KHz). > > - * For delay on/off zero default setting 3KHz is used. > > + /* HW supports two types of blinking: full (6Hz) and half (3Hz). > > + * For delay on/off zero default setting 3Hz is used. > > */ > > if (!(*delay_on == 0 && *delay_off == 0) && > > !(*delay_on == LED_BLINK_3HZ && *delay_off == LED_BLINK_3HZ) > && > > > > > -- > Best regards, > Jacek Anaszewski
