Recent versions of this IP support automatic erased page detection.
If an erased page is detected on reads, the controller does not set
INTR__ECC_UNCOR_ERR, but INTR__ERASED_PAGE.
The detection of erased pages is based on the number of zeros in a
page; if the number of zeros is less than the value in the field
ERASED_THRESHOLD, the page is assumed as erased.
Please note ERASED_THRESHOLD specifies the number of zeros in a _page_
instead of an ECC chunk. Moreover, the controller does not provide a
way to know the actual number of bitflips.
Actually, an erased page (all 0xff) is not an ECC correctable pattern
on the Denali ECC engine. In other words, there may be overlap between
the following two:
[1] a bit pattern reachable from a valid payload + ECC pattern within
ecc.strength bitflips
[2] a bit pattern reachable from an erased state (all 0xff) within
ecc.strength bitflips
So, this feature may intercept ECC correctable patterns, then replace
[1] with [2].
After all, this feature can work safely only when ECC_THRESHOLD == 1,
i.e. detect erased pages without any bitflips. This should be the
case most of the time. If there is a bitflip or more, the driver will
fallback to the software method by using nand_check_erased_ecc_chunk().
Strangely enough, the driver still has to fill the buffer with 0xff
in case of INTR__ERASED_PAGE because the ECC correction engine has
already manipulated the data in the buffer before it judges erased
pages.
Signed-off-by: Masahiro Yamada <yamada.masah...@socionext.com>
---
Changes in v6:
- memset(buf, 0xff, size) is necessary even if the page is completely
erased (all 0xff), strangely.
Changes in v5:
- Set ECC_THRESHOLD to 1
Changes in v4: None
Changes in v3: None
Changes in v2:
- Newly added
drivers/mtd/nand/denali.c | 9 ++++++++-
drivers/mtd/nand/denali.h | 5 +++++
2 files changed, 13 insertions(+), 1 deletion(-)
diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c
index d58ea17c0a69..1ded7cc00b1a 100644
--- a/drivers/mtd/nand/denali.c
+++ b/drivers/mtd/nand/denali.c
@@ -552,6 +552,9 @@ static int denali_pio_read(struct denali_nand_info *denali,
void *buf,
if (!(irq_status & INTR__PAGE_XFER_INC))
return -EIO;
+ if (irq_status & INTR__ERASED_PAGE)
+ memset(buf, 0xff, size);
+
return irq_status & ecc_err_mask ? -EBADMSG : 0;
}
@@ -627,6 +630,9 @@ static int denali_dma_xfer(struct denali_nand_info *denali,
void *buf,
denali_enable_dma(denali, false);
dma_sync_single_for_cpu(denali->dev, dma_addr, size, dir);
+ if (irq_status & INTR__ERASED_PAGE)
+ memset(buf, 0xff, size);
+
return ret;
}
@@ -1397,7 +1403,8 @@ int denali_init(struct denali_nand_info *denali)
"chosen ECC settings: step=%d, strength=%d, bytes=%d\n",
chip->ecc.size, chip->ecc.strength, chip->ecc.bytes);
- iowrite32(chip->ecc.strength, denali->flash_reg + ECC_CORRECTION);
+ iowrite32(MAKE_ECC_CORRECTION(chip->ecc.strength, 1),
+ denali->flash_reg + ECC_CORRECTION);
iowrite32(mtd->erasesize / mtd->writesize,
denali->flash_reg + PAGES_PER_BLOCK);
iowrite32(chip->options & NAND_BUSWIDTH_16 ? 1 : 0,
diff --git a/drivers/mtd/nand/denali.h b/drivers/mtd/nand/denali.h
index f5da52f09e34..657a794af695 100644
--- a/drivers/mtd/nand/denali.h
+++ b/drivers/mtd/nand/denali.h
@@ -110,6 +110,10 @@
#define ECC_CORRECTION 0x1b0
#define ECC_CORRECTION__VALUE GENMASK(4, 0)
+#define ECC_CORRECTION__ERASE_THRESHOLD GENMASK(31, 16)
+#define MAKE_ECC_CORRECTION(val, thresh) \
+ (((val) & (ECC_CORRECTION__VALUE)) | \
+ (((thresh) << 16) & (ECC_CORRECTION__ERASE_THRESHOLD)))
#define READ_MODE 0x1c0
#define READ_MODE__VALUE GENMASK(3, 0)
@@ -233,6 +237,7 @@
#define INTR__RST_COMP BIT(13)
#define INTR__PIPE_CMD_ERR BIT(14)
#define INTR__PAGE_XFER_INC BIT(15)
+#define INTR__ERASED_PAGE BIT(16)
#define PAGE_CNT(bank) (0x430 + (bank) * 0x50)
#define ERR_PAGE_ADDR(bank) (0x440 + (bank) * 0x50)
--
2.7.4
