Hello Rob,
On 06/23/2017 08:55 PM, Rob Herring wrote:
> On Fri, Jun 16, 2017 at 03:57:31PM +0200, olivier moysan wrote:
>> This adds documentation of device tree bindings for the
>> STM32 SPDIFRX interface.
>>
>> Signed-off-by: olivier moysan <olivier.moy...@st.com>
>> ---
>> .../devicetree/bindings/sound/st,stm32-spdifrx.txt | 56
>> ++++++++++++++++++++++
>> 1 file changed, 56 insertions(+)
>> create mode 100644
>> Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
>>
>> diff --git a/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
>> b/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
>> new file mode 100644
>> index 0000000..33826f2
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
>> @@ -0,0 +1,56 @@
>> +STMicroelectronics STM32 S/PDIF receiver (SPDIFRX).
>> +
>> +The SPDIFRX peripheral, is designed to receive an S/PDIF flow compliant with
>> +IEC-60958 and IEC-61937.
>> +
>> +Required properties:
>> + - compatible: should be "st,stm32h7-spdifrx"
>> + - reg: cpu DAI IP base address and size
>> + - clocks: must contain an entry for kclk (used as S/PDIF signal reference)
>> + - clock-names: must contain "kclk"
>> + - interrupts: cpu DAI interrupt line
>> + - dmas: DMA specifiers for audio data DMA and iec control flow DMA
>> + See STM32 DMA bindings,
>> Documentation/devicetree/bindings/dma/stm32-dma.txt
>> + - dma-names: two dmas have to be defined, "rx" and "rx-ctrl"
>> +
>> +Optional properties:
>> + - resets: Reference to a reset controller asserting the SPDIFRX
>> +
>> +The device node should contain one 'port' child node with one child
>> 'endpoint'
>> +node, according to the bindings defined in
>> Documentation/devicetree/bindings/
>> +graph.txt.
>> +
>> +Example:
>> +spdifrx: spdifrx@40004000 {
>> + compatible = "st,stm32h7-spdifrx";
>> + reg = <0x40004000 0x400>;
>> + clocks = <&rcc SPDIFRX_CK>;
>> + clock-names = "kclk";
>> + interrupts = <97>;
>> + dmas = <&dmamux1 2 93 0x400 0x0>,
>> + <&dmamux1 3 94 0x400 0x0>;
>> + dma-names = "rx", "rx-ctrl";
>> + pinctrl-0 = <&spdifrx_pins>;
>> + pinctrl-names = "default";
>> +
>> + spdifrx_port: port {
>> + cpu_endpoint: endpoint {
>> + remote-endpoint = <&codec_endpoint>;
>> + };
>> + };
>> +};
>> +
>> +spdif_in: spdif-in {
>> + compatible = "linux,spdif-dir";
>
> What is this? It should go.
>
> Rob
>
This is the ASoC spdif stub codec. This is relevant in DT when
spdif interface is wired to a connector.
I will remove it from bindings.
BRs
olivier
