Hello Corentin, Chen-Yu

在 2017/8/9 16:45, Corentin Labbe 写道:
On Thu, Aug 03, 2017 at 07:06:33PM +0800, Chen-Yu Tsai wrote:
On Thu, Aug 3, 2017 at 1:38 AM, Florian Fainelli <f.faine...@gmail.com> wrote:
On 08/01/2017 11:21 PM, David Wu wrote:
To make internal phy work, need to configure the phy_clock,
phy cru_reset and related registers.

Signed-off-by: David Wu <david...@rock-chips.com>
  .../devicetree/bindings/net/rockchip-dwmac.txt     |  6 +-
  drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c     | 81 ++++++++++++++++++++++
  2 files changed, 86 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt 
index 8f42755..ec39b31 100644
--- a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
+++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
@@ -25,7 +25,8 @@ Required properties:
   - clock-names: One name for each entry in the clocks property.
   - phy-mode: See ethernet.txt file in the same directory.
   - pinctrl-names: Names corresponding to the numbered pinctrl states.
- - pinctrl-0: pin-control mode. can be <&rgmii_pins> or <&rmii_pins>.
+ - pinctrl-0: pin-control mode. can be <&rgmii_pins>, <&rmii_pins> or led pins
+   for internal phy mode.
   - clock_in_out: For RGMII, it must be "input", means main clock(125MHz)
     is not sourced from SoC's PLL, but input from PHY; For RMII, "input" means
     PHY provides the reference clock(50MHz), "output" means GMAC provides the
@@ -40,6 +41,9 @@ Optional properties:
   - tx_delay: Delay value for TXD timing. Range value is 0~0x7F, 0x30 as 
   - rx_delay: Delay value for RXD timing. Range value is 0~0x7F, 0x10 as 
   - phy-supply: phandle to a regulator if the PHY needs one
+ - clocks: <&cru MAC_PHY>: Clock selector for internal macphy
+ - phy-is-internal: A boolean property allows us to know that MAC will connect 
+   internal phy.

This is incorrect in two ways:

- this is a property of the PHY, so it should be documented as such in
Documentation/devicetree/bindings/net/phy.txt so other bindings can
re-use it

- if it was specific to your MAC you would expect a vendor prefix to
this property, which is not there

An alternative way to implement the external/internal logic selection
would be mandate that your Ethernet PHY node have a compatible string
like this:

phy@0 {
         compatible = "ethernet-phy-id1234.d400", "ethernet-phy-802.3-c22";

Then you don't need this phy-is-internal property, because you can
locate the PHY node by the phy-handle (see more about that in a reply to
patch 10) and you can determine ahead of time whether this PHY is
internal or not based on its compatible string.

This doesn't really work for us (sunxi). The "internal" PHY of the H3
is also available in the X-Powers AC200 combo chip, which would be
external. Same ID. So if someone were to be stupid and put the two
together, you wouldn't know which one it actually is. Generically
it doesn't make sense to match against the ID either. The PHY is
only integrated or inlined into the SoC, meaning it could be moved
elsewhere or even be a discreet part.

The way I see it is more like a reversed pinmux. The system should
select either the internal set or external set of xMII pins to use.

A phy-is-internal property in the PHY node would work for us. We
already need a PHY node to describe its clocks and resets.

A side note to this solution is that, since the internal PHY is defined
at the .dtsi level, any external PHYs at the same address would need to
make sure to delete the property, which is kind of counterintuitive, but
it is how device tree works. One would want to put the internal PHY's
address, assuming it is configurable, on something that is rarely used.

Hello David, Florian, Andrew

Could someone ack this ? or nack if you think that the chance for having two 
PHY id both internal and external is too low.
Anyway, we need a choice.

I think we should be specific to the situation, for us we have the possibility that the Mac only picks up internal PHY, so this can be fixed at the. DTSi level, also possible INTERNL PHY's Mac can also be used to connect external PHY, while cutting off the connection with the internal PHY, so we should define the internal PHY at the DTS level, so I think Florian's approach is acceptable.


Reply via email to