在 2018-04-03二的 21:40 +0800，Icenowy Zheng写道： > As the definition of CCU slice macros are already merged into the > source > tree, restore the usage of the macros now.
Maxime, could you check this patch and pick it? Thanks! > > Signed-off-by: Icenowy Zheng <[email protected]> > --- > arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 20 +++++++++++------- > -- > 1 file changed, 11 insertions(+), 9 deletions(-) > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi > b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi > index 56563150d61a..4debc3962830 100644 > --- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi > @@ -4,6 +4,8 @@ > */ > > #include <dt-bindings/interrupt-controller/arm-gic.h> > +#include <dt-bindings/clock/sun50i-h6-ccu.h> > +#include <dt-bindings/reset/sun50i-h6-ccu.h> > > / { > interrupt-parent = <&gic>; > @@ -115,7 +117,7 @@ > <GIC_SPI 53 > IRQ_TYPE_LEVEL_HIGH>, > <GIC_SPI 54 > IRQ_TYPE_LEVEL_HIGH>, > <GIC_SPI 59 > IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&ccu 26>, <&osc24M>, <&osc32k>; > + clocks = <&ccu CLK_APB1>, <&osc24M>, > <&osc32k>; > clock-names = "apb", "hosc", "losc"; > gpio-controller; > #gpio-cells = <3>; > @@ -134,8 +136,8 @@ > interrupts = <GIC_SPI 0 > IRQ_TYPE_LEVEL_HIGH>; > reg-shift = <2>; > reg-io-width = <4>; > - clocks = <&ccu 70>; > - resets = <&ccu 21>; > + clocks = <&ccu CLK_BUS_UART0>; > + resets = <&ccu RST_BUS_UART0>; > status = "disabled"; > }; > > @@ -145,8 +147,8 @@ > interrupts = <GIC_SPI 1 > IRQ_TYPE_LEVEL_HIGH>; > reg-shift = <2>; > reg-io-width = <4>; > - clocks = <&ccu 71>; > - resets = <&ccu 22>; > + clocks = <&ccu CLK_BUS_UART1>; > + resets = <&ccu RST_BUS_UART1>; > status = "disabled"; > }; > > @@ -156,8 +158,8 @@ > interrupts = <GIC_SPI 2 > IRQ_TYPE_LEVEL_HIGH>; > reg-shift = <2>; > reg-io-width = <4>; > - clocks = <&ccu 72>; > - resets = <&ccu 23>; > + clocks = <&ccu CLK_BUS_UART2>; > + resets = <&ccu RST_BUS_UART2>; > status = "disabled"; > }; > > @@ -167,8 +169,8 @@ > interrupts = <GIC_SPI 3 > IRQ_TYPE_LEVEL_HIGH>; > reg-shift = <2>; > reg-io-width = <4>; > - clocks = <&ccu 73>; > - resets = <&ccu 24>; > + clocks = <&ccu CLK_BUS_UART3>; > + resets = <&ccu RST_BUS_UART3>; > status = "disabled"; > }; > };
