This adds support for the Zodiac Inflight Innovations SCU2 Ethernet Switch Board, which is based on the i.MX51.
Signed-off-by: Andrey Gusakov <[email protected]> --- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/imx51-zii-scu2-esb.dts | 178 +++++++++++++++++++++++++++++++ 2 files changed, 180 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/imx51-zii-scu2-esb.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 37a3de7..d8900f4 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -358,7 +358,8 @@ dtb-$(CONFIG_SOC_IMX51) += \ imx51-digi-connectcore-jsk.dtb \ imx51-eukrea-mbimxsd51-baseboard.dtb \ imx51-ts4800.dtb \ - imx51-zii-rdu1.dtb + imx51-zii-rdu1.dtb \ + imx51-zii-scu2-esb.dtb dtb-$(CONFIG_SOC_IMX53) += \ imx53-ard.dtb \ imx53-cx9020.dtb \ diff --git a/arch/arm/boot/dts/imx51-zii-scu2-esb.dts b/arch/arm/boot/dts/imx51-zii-scu2-esb.dts new file mode 100644 index 0000000..e052133 --- /dev/null +++ b/arch/arm/boot/dts/imx51-zii-scu2-esb.dts @@ -0,0 +1,178 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +// Copyright (C) 2018 Zodiac Inflight Innovations + +/dts-v1/; +#include "imx51-zii-common.dtsi" + +/ { + model = "ZII SCU2 ESB board"; + compatible = "zii,imx51-scu2-esb", "fsl,imx51"; +}; + +&esdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_esdhc1_4bit &pinctrl_esdhc1_8bit>; + bus-width = <8>; +}; + +&fec { + phy-reset-gpios = <&gpio4 21 GPIO_ACTIVE_LOW>; + + fixed-link { + speed = <100>; + full-duplex; + }; + + fec_mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + switch@0 { + compatible = "marvell,mv88e6085"; + reg = <0>; + dsa,member = <0 0>; + eeprom-length = <512>; + interrupt-parent = <&gpio4>; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "port1"; + }; + + port@1 { + reg = <1>; + label = "port2"; + }; + + port@2 { + reg = <2>; + label = "port3"; + }; + + port@3 { + reg = <3>; + label = "scu2scu"; + }; + + port@4 { + reg = <4>; + label = "esb2host"; + }; + port@5 { + reg = <5>; + label = "esb2mezz"; + phy-mode = "sgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + port@6 { + reg = <6>; + label = "cpu"; + phy-mode = "mii"; + ethernet = <&fec>; + + fixed-link { + speed = <100>; + full-duplex; + }; + }; + }; + }; + }; +}; + +&i2c2 { + lm75@48 { + compatible = "national,lm75"; + reg = <0x48>; + }; +}; + +&i2c_gpio { + gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>, /* sda */ + <&gpio3 0 GPIO_ACTIVE_HIGH>; /* scl */ +}; + +&ipu { + status = "disabled"; +}; + +&usb_vbus { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_mmc_reset>; + gpio = <&gpio4 19 GPIO_ACTIVE_LOW>; + startup-delay-us = <150000>; +}; + +&iomuxc { + pinctrl_fec: fecgrp { + fsl,pins = < + MX51_PAD_DISP2_DAT15__FEC_TDATA0 0x2004 + MX51_PAD_DISP2_DAT6__FEC_TDATA1 0x2004 + MX51_PAD_DISP2_DAT7__FEC_TDATA2 0x2004 + MX51_PAD_DISP2_DAT8__FEC_TDATA3 0x2004 + MX51_PAD_DISP2_DAT9__FEC_TX_EN 0x2004 + MX51_PAD_DISP2_DAT10__FEC_COL 0x0180 + MX51_PAD_DISP2_DAT11__FEC_RX_CLK 0x0180 + MX51_PAD_DISP2_DAT12__FEC_RX_DV 0x20a4 + MX51_PAD_DISP2_DAT13__FEC_TX_CLK 0x2180 + MX51_PAD_DISP2_DAT14__FEC_RDATA0 0x2180 + MX51_PAD_DI2_DISP_CLK__FEC_RDATA1 0x0085 + MX51_PAD_DI_GP4__FEC_RDATA2 0x0085 + MX51_PAD_DISP2_DAT0__FEC_RDATA3 0x0085 + MX51_PAD_DI2_PIN2__FEC_MDC 0x2004 + MX51_PAD_DI2_PIN3__FEC_MDIO 0x01f5 + MX51_PAD_DI2_PIN4__FEC_CRS 0x0180 + MX51_PAD_AUD3_BB_FS__GPIO4_21 0x0000 + >; + }; + + pinctrl_swi2c: swi2cgrp { + fsl,pins = < + MX51_PAD_DI1_PIN11__GPIO3_0 0x100 + MX51_PAD_DI1_PIN12__GPIO3_1 0x100 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX51_PAD_UART1_RXD__UART1_RXD 0x1c5 + MX51_PAD_UART1_TXD__UART1_TXD 0x1c5 + MX51_PAD_UART1_RTS__UART1_RTS 0x1c5 + MX51_PAD_UART1_CTS__UART1_CTS 0x1c5 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX51_PAD_UART2_RXD__UART2_RXD 0x1c5 + MX51_PAD_UART2_TXD__UART2_TXD 0x1c5 + MX51_PAD_USBH1_DATA0__UART2_CTS 0x1c5 + MX51_PAD_USBH1_DATA3__UART2_RTS 0x1c5 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX51_PAD_UART3_RXD__UART3_RXD 0x1c5 + MX51_PAD_UART3_TXD__UART3_TXD 0x1c5 + >; + }; + + pinctrl_usb_mmc_reset: usbmmcgrp { + fsl,pins = < + MX51_PAD_AUD3_BB_RXD__GPIO4_19 0x100 + >; + }; +}; -- 1.9.1
