Poll PLLX lock-status instead of delaying for a constant time. This speeds
up resume from suspend a tad and is less error-prone since lock failure
will be reported.
Signed-off-by: Dmitry Osipenko <dig...@gmail.com>
---
drivers/clk/tegra/clk-tegra20.c | 51 +++++++++++++++++++++++++++------
drivers/clk/tegra/clk-tegra30.c | 51 +++++++++++++++++++++++++++------
2 files changed, 86 insertions(+), 16 deletions(-)
diff --git a/drivers/clk/tegra/clk-tegra20.c b/drivers/clk/tegra/clk-tegra20.c
index f987ed361df6..c8146e65e7ad 100644
--- a/drivers/clk/tegra/clk-tegra20.c
+++ b/drivers/clk/tegra/clk-tegra20.c
@@ -15,6 +15,7 @@
*/
#include <linux/io.h>
+#include <linux/iopoll.h>
#include <linux/clk-provider.h>
#include <linux/clkdev.h>
#include <linux/of.h>
@@ -1001,6 +1002,47 @@ static void tegra20_cpu_clock_suspend(void)
readl(clk_base + SUPER_CCLK_DIVIDER);
}
+static void tegra20_cpu_clock_restore_pllx(void)
+{
+ u32 misc = readl_relaxed(clk_base + PLLX_MISC);
+ u32 base = readl_relaxed(clk_base + PLLX_BASE);
+ u32 misc_restore = tegra20_cpu_clk_sctx.pllx_misc;
+ u32 base_restore = tegra20_cpu_clk_sctx.pllx_base;
+ int err;
+
+ /* nothing to do if PLL configuration is unchanged */
+ if (misc == misc_restore && base == base_restore)
+ return;
+
+ /* otherwise restore configuration */
+ if (base_restore & BIT(30)) {
+ /* PLL shall be locked if we are going to (re)enable it */
+ misc_restore |= BIT(18);
+ }
+
+ /* disable PLL if it is enabled to re-apply configuration safely */
+ if (base & BIT(30)) {
+ writel_relaxed(base & ~BIT(30), clk_base + PLLX_BASE);
+ udelay(1);
+ }
+
+ /* restore the configuration */
+ writel_relaxed(misc_restore, clk_base + PLLX_MISC);
+ writel_relaxed(base_restore, clk_base + PLLX_BASE);
+
+ /* PLL is disabled now, nothing left to do */
+ if (!(base_restore & BIT(30)))
+ return;
+
+ /* otherwise start polling the PLL lock-status */
+ err = readl_relaxed_poll_timeout_atomic(clk_base + PLLX_BASE, base,
+ base & BIT(27), 1, 2000);
+ /* should not happen */
+ WARN_ONCE(err, "PLLX failed to lock: %d\n", err);
+ /* post-enable delay */
+ udelay(50);
+}
+
static void tegra20_cpu_clock_resume(void)
{
unsigned int reg, policy;
@@ -1018,14 +1060,7 @@ static void tegra20_cpu_clock_resume(void)
if (reg != CCLK_BURST_POLICY_PLLX) {
/* restore PLLX settings if CPU is on different PLL */
- writel(tegra20_cpu_clk_sctx.pllx_misc,
- clk_base + PLLX_MISC);
- writel(tegra20_cpu_clk_sctx.pllx_base,
- clk_base + PLLX_BASE);
-
- /* wait for PLL stabilization if PLLX was enabled */
- if (tegra20_cpu_clk_sctx.pllx_base & (1 << 30))
- udelay(300);
+ tegra20_cpu_clock_restore_pllx();
}
/*
diff --git a/drivers/clk/tegra/clk-tegra30.c b/drivers/clk/tegra/clk-tegra30.c
index 0f8797ca39e2..0059fdf79169 100644
--- a/drivers/clk/tegra/clk-tegra30.c
+++ b/drivers/clk/tegra/clk-tegra30.c
@@ -15,6 +15,7 @@
*/
#include <linux/io.h>
+#include <linux/iopoll.h>
#include <linux/delay.h>
#include <linux/clk-provider.h>
#include <linux/clkdev.h>
@@ -1189,6 +1190,47 @@ static void tegra30_cpu_clock_suspend(void)
readl(clk_base + CLK_RESET_CCLK_DIVIDER);
}
+static void tegra30_cpu_clock_restore_pllx(void)
+{
+ u32 misc = readl_relaxed(clk_base + CLK_RESET_PLLX_MISC);
+ u32 base = readl_relaxed(clk_base + CLK_RESET_PLLX_BASE);
+ u32 misc_restore = tegra30_cpu_clk_sctx.pllx_misc;
+ u32 base_restore = tegra30_cpu_clk_sctx.pllx_base;
+ int err;
+
+ /* nothing to do if PLL configuration is unchanged */
+ if (misc == misc_restore && base == base_restore)
+ return;
+
+ /* otherwise restore configuration */
+ if (base_restore & BIT(30)) {
+ /* PLL shall be locked if we are going to (re)enable it */
+ misc_restore |= BIT(18);
+ }
+
+ /* disable PLL if it is enabled to re-apply configuration safely */
+ if (base & BIT(30)) {
+ writel_relaxed(base & ~BIT(30), clk_base + CLK_RESET_PLLX_BASE);
+ udelay(1);
+ }
+
+ /* restore the configuration */
+ writel_relaxed(misc_restore, clk_base + CLK_RESET_PLLX_MISC);
+ writel_relaxed(base_restore, clk_base + CLK_RESET_PLLX_BASE);
+
+ /* PLL is disabled now, nothing left to do */
+ if (!(base_restore & BIT(30)))
+ return;
+
+ /* otherwise start polling the PLL lock-status */
+ err = readl_relaxed_poll_timeout_atomic(clk_base + CLK_RESET_PLLX_BASE,
+ base, base & BIT(27), 1, 2000);
+ /* should not happen */
+ WARN_ONCE(err, "PLLX failed to lock: %d\n", err);
+ /* post-enable delay */
+ udelay(50);
+}
+
static void tegra30_cpu_clock_resume(void)
{
unsigned int reg, policy;
@@ -1206,14 +1248,7 @@ static void tegra30_cpu_clock_resume(void)
if (reg != CLK_RESET_CCLK_BURST_POLICY_PLLX) {
/* restore PLLX settings if CPU is on different PLL */
- writel(tegra30_cpu_clk_sctx.pllx_misc,
- clk_base + CLK_RESET_PLLX_MISC);
- writel(tegra30_cpu_clk_sctx.pllx_base,
- clk_base + CLK_RESET_PLLX_BASE);
-
- /* wait for PLL stabilization if PLLX was enabled */
- if (tegra30_cpu_clk_sctx.pllx_base & (1 << 30))
- udelay(300);
+ tegra30_cpu_clock_restore_pllx();
}
/*
--
2.18.0
