On Mon, Sep 24, 2018 at 10:53:13PM +0200, Arnd Bergmann wrote:
> On Tue, Sep 18, 2018 at 3:42 PM Lorenzo Pieralisi
> <[email protected]> wrote:
> >
> > On Mon, Jun 04, 2018 at 09:17:49AM -0500, Rob Herring wrote:
> > > +Arnd
> > >
> > > On Tue, May 29, 2018 at 4:58 PM, Ray Jui <[email protected]> wrote:
> > > > Update the iProc PCIe binding document for better modeling of the legacy
> > > > interrupt (INTx) support
> > > >
> > > > Signed-off-by: Ray Jui <[email protected]>
> > > > ---
> > > > .../devicetree/bindings/pci/brcm,iproc-pcie.txt | 31
> > > > +++++++++++++++++-----
> > > > 1 file changed, 24 insertions(+), 7 deletions(-)
> > > >
> > > > diff --git a/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
> > > > b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
> > > > index b8e48b4..7ea24dc 100644
> > > > --- a/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
> > > > +++ b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
> > > > @@ -13,9 +13,6 @@ controller, used in Stingray
> > > > PAXB-based root complex is used for external endpoint devices.
> > > > PAXC-based
> > > > root complex is connected to emulated endpoint devices internal to the
> > > > ASIC
> > > > - reg: base address and length of the PCIe controller I/O register
> > > > space
> > > > -- #interrupt-cells: set to <1>
> > > > -- interrupt-map-mask and interrupt-map, standard PCI properties to
> > > > define the
> > > > - mapping of the PCIe interface to interrupt numbers
> > > > - linux,pci-domain: PCI domain ID. Should be unique for each host
> > > > controller
> > > > - bus-range: PCI bus numbers covered
> > > > - #address-cells: set to <3>
> > > > @@ -41,6 +38,16 @@ Required:
> > > > - brcm,pcie-ob-axi-offset: The offset from the AXI address to the
> > > > internal
> > > > address used by the iProc PCIe core (not the PCIe address)
> > > >
> > > > +Legacy interrupt (INTx) support (optional):
> > > > +
> > > > +Note INTx is for PAXB only.
> > > > +
> > > > +- interrupt-controller: claims itself as an interrupt controller for
> > > > INTx
> > > > +- #interrupt-cells: set to <1>
> > > > +- interrupt-map-mask and interrupt-map, standard PCI properties to
> > > > define
> > > > +the mapping of the PCIe interface to interrupt numbers
> > > > +- interrupts: interrupt line wired to the generic GIC for INTx support
> > > > +
> > > > MSI support (optional):
> > > >
> > > > For older platforms without MSI integrated in the GIC, iProc PCIe core
> > > > provides
> > > > @@ -77,9 +84,14 @@ Example:
> > > > compatible = "brcm,iproc-pcie";
> > > > reg = <0x18012000 0x1000>;
> > > >
> > > > + interrupt-controller;
> > > > #interrupt-cells = <1>;
> > > > - interrupt-map-mask = <0 0 0 0>;
> > > > - interrupt-map = <0 0 0 0 &gic GIC_SPI 100
> > > > IRQ_TYPE_NONE>;
> > > > + interrupt-map-mask = <0 0 0 7>;
> > > > + interrupt-map = <0 0 0 1 &pcie0 1>,
> > >
> > > Are you sure this works? The irq parsing code will ignore
> > > interrupt-map if interrupt-controller is found. In other words, you
> > > should have one or the other, but not both.
> > >
> > > Maybe it happens to work because "pcie0" is this node and your irq
> > > numbers are the same.
> > >
> > > Arnd, any thoughts on this?
> >
> > To start with, I think the destination IRQ number is wrong, what the
> > mappings actually do is mapping the PCI interrupt line (ie #INTA, #INTB,
> > #INTC, #INTD) to input {0,1,2,3} of the PCI host bridge (pseudo)
> > interrupt controller.
> >
> > I really want to clean this up since currently there are different
> > DT bindings defining this in different ways which resulted in
> > non-consistent kernel code.
> >
> > AFAICS, the Aardvark PCIe controller bindings define the mapping
> > as I expect:
> >
> > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/pci/aardvark-pci.txt?h=v4.19-rc4
> >
> > but I would like to get Rob and Arnd viewpoint on this so that
> > we can close this topic once for all.
>
> It seems ambiguous at best, as Rob suggested it may only
> work by accident. Since there is only one upstream interrupt,
> could we simply list <GIC_SPI 100 IRQ_TYPE_NONE> as
> the destination for any IntX?
I think that would not be correct from an HW description standpoint
since there is some logic in the host bridge that behaves as an
interrupt controller (eg registers to ack/mask IRQs).
AFAICS the aardvark (it is an example) bindings below should be correct,
with an interrupt controller node within the PCI host bridge:
pcie0: pcie@d0070000 {
compatible = "marvell,armada-3700-pcie";
device_type = "pci";
reg = <0 0xd0070000 0 0x20000>;
#address-cells = <3>;
#size-cells = <2>;
bus-range = <0x00 0xff>;
interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
#interrupt-cells = <1>;
msi-controller;
msi-parent = <&pcie0>;
ranges = <0x82000000 0 0xe8000000 0 0xe8000000 0 0x1000000 /*
Port 0 MEM */
0x81000000 0 0xe9000000 0 0xe9000000 0 0x10000>; /*
Port 0 IO*/
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0 0 0 1 &pcie_intc 0>,
<0 0 0 2 &pcie_intc 1>,
<0 0 0 3 &pcie_intc 2>,
<0 0 0 4 &pcie_intc 3>;
pcie_intc: interrupt-controller {
interrupt-controller;
#interrupt-cells = <1>;
};
};
Thoughts ?
Lorenzo
