Hi Boris, > -----Original Message----- > From: Boris Brezillon [mailto:boris.brezil...@bootlin.com] > Sent: Monday, October 15, 2018 5:24 PM > To: Yogesh Narayan Gaur <yogeshnarayan.g...@nxp.com> > Cc: linux-...@lists.infradead.org; marek.va...@gmail.com; vigne...@ti.com; > linux-...@vger.kernel.org; devicet...@vger.kernel.org; r...@kernel.org; > mark.rutl...@arm.com; shawn...@kernel.org; linux-arm- > ker...@lists.infradead.org; computersforpe...@gmail.com; > frieder.schre...@exceet.de; linux-kernel@vger.kernel.org > Subject: Re: [PATCH v2 0/7] spi: add support for octal mode > > Hi Yogesh, > > On Mon, 15 Oct 2018 11:47:55 +0000 > Yogesh Narayan Gaur <yogeshnarayan.g...@nxp.com> wrote: > > > Add support for octal mode IO data transfer. > > Micron flash, mt35xu512aba, supports octal mode data transfer and NXP > > FlexSPI controller supports 8 data lines for data transfer (Rx/Tx). > > > > Patch series > > * Add support for octal mode flags and parsing of same in spi driver. > > * Add opcodes for octal I/O commands in spi-nor framework, Read and Write > proto for (1-1-8/1-8-8) mode. > > Opcodes are added as per octal data IO commands required for > mt35xu512aba [1] flash. > > * Add parsing logic for spi-mem framework and m25p80.c device file. > > * Add mode bit required for octal mode in nxp-fspi driver [2]. > > * Define binding property 'spi-rx/tx-bus-width' for LX2160ARDB target [2]. > > > > Cherry pick below 2 patches (from: > https://emea01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fgit.ker > nel.org%2Fpub%2Fscm%2Flinux%2Fkernel%2Fgit%2Fbroonie%2Fspi.git&da > ta=02%7C01%7Cyogeshnarayan.gaur%40nxp.com%7C9af69996cae344b6e7b70 > 8d63294eaf5%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C6367520 > 12521352025&sdata=euwK9X2tael3Q69QO%2BirRznB%2BHKazDbumdAOp > eZvxCc%3D&reserved=0): > > c639f871febe6667d9afce28108c634e5636c735 spi: spi-mem: Fix inverted > logic in op sanity check > > db122eb8a749a1eff038f9a282c620ab16c4be1d spi: spi-mem: Add extra > > sanity checks on the op param > > > > Tested on LX2160ARDB target with nxp-fspi driver, below are Read > > performance number of 1-1-1 and 1-1-8 read protocol. > > > > root@lxxx:~# cat /proc/mtd > > dev: size erasesize name > > mtd0: 04000000 00001000 "spi0.0" > > mtd1: 04000000 00001000 "spi0.1" > > root@lxxx:~# time mtd_debug read /dev/mtd0 0x0 0x1000000 0read > > Copied 16777216 bytes from address 0x00000000 in flash to 0read > > > > real 0m2.792s > > user 0m0.000s > > sys 0m2.790s > > root@lxxx:~# time mtd_debug read /dev/mtd1 0x0 0x1000000 0read > > Copied 16777216 bytes from address 0x00000000 in flash to 0read > > > > real 0m0.441s > > user 0m0.000s > > sys 0m0.440s > > root@ls1012ardb:~# > > > > Flash device MTD0 configured in 1-1-1 protocol. > > Flash device MTD1 configured in 1-1-8 protocol. > > > > [1] > > https://emea01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fpat > > chwork.ozlabs.org%2Fproject%2Flinux- > mtd%2Flist%2F%3Fseries%3D70384& > > ;data=02%7C01%7Cyogeshnarayan.gaur%40nxp.com%7C9af69996cae344b6e > 7b708d > > > 63294eaf5%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C636752012 > 521352 > > > 025&sdata=ldk0ny8vksO%2FayIsYX26M4akFUojtaP1YyOtpMEGJZA%3D&a > mp;res > > erved=0 [2] > > https://emea01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fpat > > chwork.ozlabs.org%2Fproject%2Flinux- > mtd%2Flist%2F%3Fseries%3D70210& > > ;data=02%7C01%7Cyogeshnarayan.gaur%40nxp.com%7C9af69996cae344b6e > 7b708d > > > 63294eaf5%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C636752012 > 521352 > > > 025&sdata=wq%2BCnrk4Ovx4itHrZfv%2FGH5raStF91hfjHBQmO9Sjq0%3D& > amp;r > > eserved=0 > > > > Yogesh Gaur (7): > > spi: add support for octal I/O data transfer > > mtd: spi-nor: add opcodes for octal Read/Write commands > > mtd: spi-nor: add octal read flag for flash mt35xu512aba > > mtd: m25p80: add support of octal I/O transfer > > spi: spi-mem: add support for octal I/O data transfer > > Patch 5 should be moved before patch 4 (ideally in 2nd position) if you want > this > series to be bisectable. >
Ok. For now, order which I have selected is as per the comments from Vignesh. Would resend again with the suggested order. -- Regards Yogesh Gaur > Regards, > > Boris > > > spi: nxp-fspi: add mode flag bit for octal support > > arm64: dts: lx2160a: update fspi node > > > > Changes for v2: > > Incorporated review comments of Boris and Vignesh. > > > > arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts | 4 ++++ > > drivers/mtd/devices/m25p80.c | 9 ++++++++- > > drivers/mtd/spi-nor/spi-nor.c | 15 ++++++++++++++- > > drivers/spi/spi-mem.c | 9 ++++++++- > > drivers/spi/spi-nxp-fspi.c | 4 ++-- > > drivers/spi/spi.c | 6 ++++++ > > include/linux/mtd/spi-nor.h | 8 ++++++++ > > include/linux/spi/spi.h | 2 ++ > > 8 files changed, 52 insertions(+), 5 deletions(-) > >
