From: Yue Wang <yue.w...@amlogic.com>
The Amlogic Meson PCIe host controller is based on the Synopsys DesignWare
PCI core. This patch adds documentation for the DT bindings in Meson PCIe
controller.
Signed-off-by: Yue Wang <yue.w...@amlogic.com>
Signed-off-by: Hanjie Lin <hanjie....@amlogic.com>
Reviewed-by: Rob Herring <r...@kernel.org>
---
.../devicetree/bindings/pci/amlogic,meson-pcie.txt | 70 ++++++++++++++++++++++
1 file changed, 70 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
new file mode 100644
index 0000000..12b18f8
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
@@ -0,0 +1,70 @@
+Amlogic Meson AXG DWC PCIE SoC controller
+
+Amlogic Meson PCIe host controller is based on the Synopsys DesignWare PCI
core.
+It shares common functions with the PCIe DesignWare core driver and
+inherits common properties defined in
+Documentation/devicetree/bindings/pci/designware-pci.txt.
+
+Additional properties are described here:
+
+Required properties:
+- compatible:
+ should contain "amlogic,axg-pcie" to identify the core.
+- reg:
+ should contain the configuration address space.
+- reg-names: Must be
+ - "elbi" External local bus interface registers
+ - "cfg" Meson specific registers
+ - "phy" Meson PCIE PHY registers
+ - "config" PCIe configuration space
+- reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.
+- clocks: Must contain an entry for each entry in clock-names.
+- clock-names: Must include the following entries:
+ - "pclk" PCIe GEN 100M PLL clock
+ - "port" PCIe_x(A or B) RC clock gate
+ - "general" PCIe Phy clock
+ - "mipi" PCIe_x(A or B) 100M ref clock gate
+- resets: phandle to the reset lines.
+- reset-names: must contain "phy" "port" and "apb"
+ - "phy" Share PHY reset
+ - "port" Port A or B reset
+ - "apb" Share APB reset
+- device_type:
+ should be "pci". As specified in designware-pcie.txt
+
+
+Example configuration:
+
+ pcie: pcie@f9800000 {
+ compatible = "amlogic,axg-pcie", "snps,dw-pcie";
+ reg = <0x0 0xf9800000 0x0 0x400000
+ 0x0 0xff646000 0x0 0x2000
+ 0x0 0xff644000 0x0 0x2000
+ 0x0 0xf9f00000 0x0 0x100000>;
+ reg-names = "elbi", "cfg", "phy", "config";
+ reset-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>;
+ interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 179
IRQ_TYPE_EDGE_RISING>;
+ bus-range = <0x0 0xff>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges = <0x82000000 0 0 0x0 0xf9c00000 0 0x00300000>;
+
+ clocks = <&clkc CLKID_USB
+ &clkc CLKID_MIPI_ENABLE
+ &clkc CLKID_PCIE_A
+ &clkc CLKID_PCIE_CML_EN0>;
+ clock-names = "general",
+ "mipi",
+ "pclk",
+ "port";
+ resets = <&reset RESET_PCIE_PHY>,
+ <&reset RESET_PCIE_A>,
+ <&reset RESET_PCIE_APB>;
+ reset-names = "phy",
+ "port",
+ "apb";
+ };
--
2.7.4
