Add devicetree support for Avenger96 board based on STM32MP157A MPU
from ST Micro. This board is one of the 96Boards Consumer Edition board
from Arrow Electronics and has the following features:
SoC: STM32MP157AAC
PMIC: STPMIC1A
RAM: 1024 Mbyte @ 533MHz
Storage: eMMC v4.51: 8 Gbyte
microSD Socket: UHS-1 v3.01
Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant
Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac
Bluetooth®v4.2 (BR/EDR/BLE)
USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG
Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4
LED: 4x User LED, 1x WiFi LED, 1x BT LED
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/avenger96/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasi...@linaro.org>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 321 ++++++++++++++++++++
2 files changed, 322 insertions(+)
create mode 100644 arch/arm/boot/dts/stm32mp157a-avenger96.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index dab2914fa293..918c85c227b5 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -975,6 +975,7 @@ dtb-$(CONFIG_ARCH_STM32) += \
stm32746g-eval.dtb \
stm32h743i-eval.dtb \
stm32h743i-disco.dtb \
+ stm32mp157a-avenger96.dtb \
stm32mp157a-dk1.dtb \
stm32mp157c-dk2.dtb \
stm32mp157c-ed1.dtb \
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
new file mode 100644
index 000000000000..9d00be78010f
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -0,0 +1,321 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasi...@linaro.org>
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c.dtsi"
+#include "stm32mp157-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+ model = "Arrow Electronics STM32MP157A Avenger96 board";
+ compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157";
+
+ aliases {
+ ethernet0 = ðernet0;
+ mmc0 = &sdmmc1;
+ serial0 = &uart4;
+ serial1 = &uart7;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@c0000000 {
+ device_type = "memory";
+ reg = <0xc0000000 0x40000000>;
+ };
+
+ led {
+ compatible = "gpio-leds";
+ led1 {
+ label = "green:user1";
+ gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+
+ led2 {
+ label = "green:user2";
+ gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ default-state = "off";
+ };
+
+ led3 {
+ label = "green:user3";
+ gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc1";
+ default-state = "off";
+ };
+
+ led4 {
+ label = "green:user3";
+ gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "none";
+ default-state = "off";
+ panic-indicator;
+ };
+
+ led5 {
+ label = "yellow:wifi";
+ gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
+ };
+
+ led6 {
+ label = "blue:bt";
+ gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "bluetooth-power";
+ default-state = "off";
+ };
+ };
+};
+
+ðernet0 {
+ status = "okay";
+ pinctrl-0 = <ðernet0_rgmii_pins_a>;
+ pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rgmii";
+ max-speed = <1000>;
+ phy-handle = <&phy0>;
+
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ phy0: ethernet-phy@7 {
+ reg = <7>;
+ };
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_b>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins_a>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ pmic: stpmic@33 {
+ compatible = "st,stpmic1";
+ reg = <0x33>;
+ interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ status = "okay";
+
+ st,main-control-register = <0x04>;
+ st,vin-control-register = <0xc0>;
+ st,usb-control-register = <0x30>;
+
+ regulators {
+ compatible = "st,stpmic1-regulators";
+
+ ldo1-supply = <&v3v3>;
+ ldo2-supply = <&v3v3>;
+ ldo3-supply = <&vdd_ddr>;
+ ldo5-supply = <&v3v3>;
+ ldo6-supply = <&v3v3>;
+ pwr_sw1-supply = <&bst_out>;
+ pwr_sw2-supply = <&bst_out>;
+
+ vddcore: buck1 {
+ regulator-name = "vddcore";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd_ddr: buck2 {
+ regulator-name = "vdd_ddr";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd: buck3 {
+ regulator-name = "vdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ st,mask_reset;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ v3v3: buck4 {
+ regulator-name = "v3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ regulator-initial-mode = <0>;
+ };
+
+ vdda: ldo1 {
+ regulator-name = "vdda";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ interrupts = <IT_CURLIM_LDO1 0>;
+ interrupt-parent = <&pmic>;
+ };
+
+ v2v8: ldo2 {
+ regulator-name = "v2v8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ interrupts = <IT_CURLIM_LDO2 0>;
+ interrupt-parent = <&pmic>;
+ };
+
+ vtt_ddr: ldo3 {
+ regulator-name = "vtt_ddr";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <750000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ vdd_usb: ldo4 {
+ regulator-name = "vdd_usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ interrupts = <IT_CURLIM_LDO4 0>;
+ interrupt-parent = <&pmic>;
+ };
+
+ vdd_sd: ldo5 {
+ regulator-name = "vdd_sd";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ interrupts = <IT_CURLIM_LDO5 0>;
+ interrupt-parent = <&pmic>;
+ regulator-boot-on;
+ };
+
+ v1v8: ldo6 {
+ regulator-name = "v1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ interrupts = <IT_CURLIM_LDO6 0>;
+ interrupt-parent = <&pmic>;
+ regulator-enable-ramp-delay = <300000>;
+ };
+
+ vref_ddr: vref_ddr {
+ regulator-name = "vref_ddr";
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ bst_out: boost {
+ regulator-name = "bst_out";
+ interrupts = <IT_OCP_BOOST 0>;
+ interrupt-parent = <&pmic>;
+ };
+
+ vbus_otg: pwr_sw1 {
+ regulator-name = "vbus_otg";
+ interrupts = <IT_OCP_OTG 0>;
+ interrupt-parent = <&pmic>;
+ regulator-active-discharge;
+ };
+
+ vbus_sw: pwr_sw2 {
+ regulator-name = "vbus_sw";
+ interrupts = <IT_OCP_SWOUT 0>;
+ interrupt-parent = <&pmic>;
+ regulator-active-discharge;
+ };
+ };
+
+ onkey {
+ compatible = "st,stpmic1-onkey";
+ interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
+ interrupt-names = "onkey-falling", "onkey-rising";
+ status = "okay";
+ };
+
+ watchdog {
+ compatible = "st,stpmic1-wdt";
+ status = "disabled";
+ };
+ };
+};
+
+&iwdg2 {
+ timeout-sec = <32>;
+ status = "okay";
+};
+
+&rng1 {
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+ broken-cd;
+ st,sig-dir;
+ st,neg-edge;
+ st,use-ckin;
+ bus-width = <4>;
+ vmmc-supply = <&vdd_sd>;
+ status = "okay";
+};
+
+&uart4 {
+ /* On Low speed expansion header */
+ label = "LS-UART1";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_b>;
+ status = "okay";
+};
+
+&uart7 {
+ /* On Low speed expansion header */
+ label = "LS-UART0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart7_pins_a>;
+ status = "okay";
+};
--
2.17.1
