Thanks for taking time to review!
On 10/06/2019 07:40, Vinod Koul wrote:
On 07-06-19, 09:56, Srinivas Kandagatla wrote:
Qualcomm SoundWire Master controller is present in most Qualcomm SoCs
either integrated as part of WCD audio codecs via slimbus or
as part of SOC I/O.
This patchset adds support to a very basic controller which has been
tested with WCD934x SoundWire controller connected to WSA881x smart
speaker amplifiers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandaga...@linaro.org>
---
drivers/soundwire/Kconfig | 9 +
drivers/soundwire/Makefile | 4 +
drivers/soundwire/qcom.c | 983 +++++++++++++++++++++++++++++++++++++
Can you split this to two patches (at least), master driver followed by
DAI driver
Sure.
+
+#define SWRM_COMP_HW_VERSION 0x00
What does COMP stand for?
Controller splits registers into "Component(core configuration
registers)", "Interrupt" "Command Fifo" and so on...
+#define SWRM_COMP_CFG_ADDR 0x04
+#define SWRM_COMP_CFG_IRQ_LEVEL_OR_PULSE_MSK BIT(1)
+#define SWRM_COMP_CFG_ENABLE_MSK BIT(0)
+#define SWRM_COMP_PARAMS 0x100
+#define SWRM_COMP_PARAMS_DOUT_PORTS_MASK GENMASK(4, 0)
+#define SWRM_COMP_PARAMS_DIN_PORTS_MASK
GENMASK(9, 5)
+#define SWRM_COMP_PARAMS_WR_FIFO_DEPTH GENMASK(14, 10)
+#define SWRM_COMP_PARAMS_RD_FIFO_DEPTH GENMASK(19, 15)
+#define SWRM_COMP_PARAMS_AUTO_ENUM_SLAVES GENMASK(32. 20)
Thats a lot of text, So as others have said we need to rethink the
naming conventions, perhaps QC_SDW_PARAM_AUTO_ENUM (feel free to drop
SDW as well from here as it QC specific!
Also move common ones to core..
+#define SWRM_INTERRUPT_STATUS 0x200
+#define SWRM_INTERRUPT_STATUS_RMSK GENMASK(16, 0)
+#define SWRM_INTERRUPT_STATUS_SLAVE_PEND_IRQ BIT(0)
+#define SWRM_INTERRUPT_STATUS_NEW_SLAVE_ATTACHED BIT(1)
+#define SWRM_INTERRUPT_STATUS_CHANGE_ENUM_SLAVE_STATUS BIT(2)
+#define SWRM_INTERRUPT_STATUS_MASTER_CLASH_DET BIT(3)
+#define SWRM_INTERRUPT_STATUS_RD_FIFO_OVERFLOW BIT(4)
+#define SWRM_INTERRUPT_STATUS_RD_FIFO_UNDERFLOW BIT(5)
+#define SWRM_INTERRUPT_STATUS_WR_CMD_FIFO_OVERFLOW BIT(6)
+#define SWRM_INTERRUPT_STATUS_CMD_ERROR BIT(7)
+#define SWRM_INTERRUPT_STATUS_DOUT_PORT_COLLISION BIT(8)
+#define SWRM_INTERRUPT_STATUS_READ_EN_RD_VALID_MISMATCH BIT(9)
+#define SWRM_INTERRUPT_STATUS_SPECIAL_CMD_ID_FINISHED BIT(10)
+#define SWRM_INTERRUPT_STATUS_NEW_SLAVE_AUTO_ENUM_FINISHED BIT(11)
+#define SWRM_INTERRUPT_STATUS_AUTO_ENUM_FAILED BIT(12)
+#define SWRM_INTERRUPT_STATUS_AUTO_ENUM_TABLE_IS_FULL BIT(13)
+#define SWRM_INTERRUPT_STATUS_BUS_RESET_FINISHED BIT(14)
+#define SWRM_INTERRUPT_STATUS_CLK_STOP_FINISHED BIT(15)
+#define SWRM_INTERRUPT_STATUS_ERROR_PORT_TEST BIT(16)
+#define SWRM_INTERRUPT_MASK_ADDR 0x204
+#define SWRM_INTERRUPT_CLEAR 0x208
+#define SWRM_CMD_FIFO_WR_CMD 0x300
+#define SWRM_CMD_FIFO_RD_CMD 0x304
+#define SWRM_CMD_FIFO_CMD 0x308
+#define SWRM_CMD_FIFO_STATUS 0x30C
+#define SWRM_CMD_FIFO_CFG_ADDR 0x314
+#define SWRM_CMD_FIFO_CFG_NUM_OF_CMD_RETRY_SHFT 0x0
+#define SWRM_CMD_FIFO_RD_FIFO_ADDR 0x318
+#define SWRM_ENUMERATOR_CFG_ADDR 0x500
+#define SWRM_MCP_FRAME_CTRL_BANK_ADDR(m) (0x101C + 0x40 * (m))
+#define SWRM_MCP_FRAME_CTRL_BANK_SSP_PERIOD_SHFT 16
+#define SWRM_MCP_FRAME_CTRL_BANK_ROW_CTRL_SHFT 3
+#define SWRM_MCP_FRAME_CTRL_BANK_COL_CTRL_BMSK GENMASK(2, 0)
+#define SWRM_MCP_FRAME_CTRL_BANK_COL_CTRL_SHFT 0
+#define SWRM_MCP_CFG_ADDR 0x1048
+#define SWRM_MCP_CFG_MAX_NUM_OF_CMD_NO_PINGS_BMSK GENMASK(21, 17)
+#define SWRM_MCP_CFG_MAX_NUM_OF_CMD_NO_PINGS_SHFT 0x11
+#define SWRM_MCP_STATUS 0x104C
+#define SWRM_MCP_STATUS_BANK_NUM_MASK BIT(0)
+#define SWRM_MCP_SLV_STATUS 0x1090
+#define SWRM_MCP_SLV_STATUS_MASK GENMASK(1, 0)
+#define SWRM_DP_PORT_CTRL_BANK(n, m) (0x1124 + 0x100 * (n - 1) + 0x40 * m)
+#define SWRM_DP_PORT_CTRL2_BANK(n, m) (0x1126 + 0x100 * (n - 1) + 0x40 * m)
+#define SWRM_DP_PORT_CTRL_EN_CHAN_SHFT 0x18
+#define SWRM_DP_PORT_CTRL_OFFSET2_SHFT 0x10
+#define SWRM_DP_PORT_CTRL_OFFSET1_SHFT 0x08
+#define SWRM_AHB_BRIDGE_WR_DATA_0 0xc885
+#define SWRM_AHB_BRIDGE_WR_ADDR_0 0xc889
+#define SWRM_AHB_BRIDGE_RD_ADDR_0 0xc88d
+#define SWRM_AHB_BRIDGE_RD_DATA_0 0xc891
+
+#define SWRM_REG_VAL_PACK(data, dev, id, reg) \
+ ((reg) | ((id) << 16) | ((dev) << 20) | ((data) << 24))
+
+#define SWRM_MAX_ROW_VAL 0 /* Rows = 48 */
+#define SWRM_DEFAULT_ROWS 48
+#define SWRM_MIN_COL_VAL 0 /* Cols = 2 */
+#define SWRM_DEFAULT_COL 16
+#define SWRM_SPECIAL_CMD_ID 0xF
+#define MAX_FREQ_NUM 1
+#define TIMEOUT_MS 1000
+#define QCOM_SWRM_MAX_RD_LEN 0xf
+#define DEFAULT_CLK_FREQ 9600000
+#define SWRM_MAX_DAIS 0xF
I was thinking it would make sense to move this to DT, DAI is after all
a hw property!
I will give that a try before sending out next version.
+static int qcom_swrm_cmd_fifo_wr_cmd(struct qcom_swrm_ctrl *ctrl, u8 cmd_data,
+ u8 dev_addr, u16 reg_addr)
+{
+ int ret = 0;
+ u8 cmd_id;
+ u32 val;
+
+ mutex_lock(&ctrl->lock);
+ if (dev_addr == SDW_BROADCAST_DEV_NUM) {
+ cmd_id = SWRM_SPECIAL_CMD_ID;
+ } else {
+ if (++ctrl->wr_cmd_id == SWRM_SPECIAL_CMD_ID)
+ ctrl->wr_cmd_id = 0;
+
+ cmd_id = ctrl->wr_cmd_id;
+ }
+
+ val = SWRM_REG_VAL_PACK(cmd_data, dev_addr, cmd_id, reg_addr);
+ ret = ctrl->reg_write(ctrl, SWRM_CMD_FIFO_WR_CMD, val);
+ if (ret < 0) {
+ dev_err(ctrl->dev, "%s: reg 0x%x write failed, err:%d\n",
+ __func__, val, ret);
+ goto err;
+ }
+
+ if (dev_addr == SDW_BROADCAST_DEV_NUM) {
+ ctrl->fifo_status = 0;
+ ret = wait_for_completion_timeout(&ctrl->sp_cmd_comp,
+ msecs_to_jiffies(TIMEOUT_MS));
why not wait for completion on non broadcast?
This could lead to dead-lock if we endup reading registers from
interrupt handler.
+static int qcom_swrm_cmd_fifo_rd_cmd(struct qcom_swrm_ctrl *ctrl,
+ u8 dev_addr, u16 reg_addr,
+ u32 len, u8 *rval)
+{
+ int i, ret = 0;
Superfluous initialization of ret
I agree.
+static irqreturn_t qcom_swrm_irq_handler(int irq, void *dev_id)
+{
+ struct qcom_swrm_ctrl *ctrl = dev_id;
+ u32 sts, value;
+
+ sts = ctrl->reg_read(ctrl, SWRM_INTERRUPT_STATUS);
+
+ if (sts & SWRM_INTERRUPT_STATUS_SPECIAL_CMD_ID_FINISHED)
+ complete(&ctrl->sp_cmd_comp);
+
+ if (sts & SWRM_INTERRUPT_STATUS_CMD_ERROR) {
+ value = ctrl->reg_read(ctrl, SWRM_CMD_FIFO_STATUS);
+ dev_err_ratelimited(ctrl->dev,
+ "CMD error, fifo status 0x%x\n",
+ value);
+ ctrl->reg_write(ctrl, SWRM_CMD_FIFO_CMD, 0x1);
+ if ((value & 0xF) == 0xF) {
+ ctrl->fifo_status = -ENODATA;
+ complete(&ctrl->sp_cmd_comp);
+ }
+ }
+
+ if ((sts & SWRM_INTERRUPT_STATUS_NEW_SLAVE_ATTACHED) ||
+ sts & SWRM_INTERRUPT_STATUS_CHANGE_ENUM_SLAVE_STATUS) {
+ if (sts & SWRM_INTERRUPT_STATUS_NEW_SLAVE_ATTACHED)
+ ctrl->status[0] = SDW_SLAVE_ATTACHED;
+
+ schedule_work(&ctrl->slave_work);
So why are we scheduling work, you are the thread handler so I think it
should be okay and better to invoke bus for status update.
I had seen lockup issues as this would trigger broadcast messages which
would wait on completion interrupt!
+ }
+
+ if (sts & SWRM_INTERRUPT_STATUS_SLAVE_PEND_IRQ)
+ dev_dbg(ctrl->dev, "Slave pend irq\n");
+
+ if (sts & SWRM_INTERRUPT_STATUS_NEW_SLAVE_ATTACHED)
+ dev_dbg(ctrl->dev, "New slave attached\n");
No updating bus on the status?
Its done down below this function! These are debug messages only!
looks redundant, will remove it.
+static enum sdw_command_response qcom_swrm_xfer_msg(struct sdw_bus *bus,
+ struct sdw_msg *msg)
+{
+ struct qcom_swrm_ctrl *ctrl = to_qcom_sdw(bus);
+ int ret, i, len;
+
+ if (msg->flags == SDW_MSG_FLAG_READ) {
+ for (i = 0; i < msg->len;) {
+ if ((msg->len - i) < QCOM_SWRM_MAX_RD_LEN)
+ len = msg->len - i;
+ else
+ len = QCOM_SWRM_MAX_RD_LEN;
+
+ ret = qcom_swrm_cmd_fifo_rd_cmd(ctrl, msg->dev_num,
+ msg->addr + i, len,
+ &msg->buf[i]);
+ if (ret < 0) {
+ if (ret == -ENODATA)
+ return SDW_CMD_IGNORED;
+
+ return ret;
+ }
+
+ i = i + len;
+ }
+ } else if (msg->flags == SDW_MSG_FLAG_WRITE) {
+ for (i = 0; i < msg->len; i++) {
+ ret = qcom_swrm_cmd_fifo_wr_cmd(ctrl, msg->buf[i],
+ msg->dev_num,
+ msg->addr + i);
+ if (ret < 0) {
+ if (ret == -ENODATA)
+ return SDW_CMD_IGNORED;
+
+ return ret;
So we need to convert this to sdw_command_response before returning.
Sure!
+static int qcom_swrm_prepare(struct snd_pcm_substream *substream,
+ struct snd_soc_dai *dai)
+{
+ struct qcom_swrm_ctrl *ctrl = dev_get_drvdata(dai->dev);
+
+ if (!ctrl->sruntime[dai->id])
+ return -EINVAL;
+
+ return sdw_enable_stream(ctrl->sruntime[dai->id]);
Hmm you need to handle dai prepare being called for multiple times.
Thanks for pointing this out, Will fix this.
+static int qcom_pdm_set_sdw_stream(struct snd_soc_dai *dai,
+ void *stream, int direction)
+{
+ return 0;
+}
lets remove if we dont intend to do anything!
Hm, not sure how I missed this one!
+static int qcom_swrm_runtime_suspend(struct device *device)
+{
+ /* TBD */
+ return 0;
+}
+
+static int qcom_swrm_runtime_resume(struct device *device)
+{
+ /* TBD */
+ return 0;
+}
Again, lets remove these, add when we have the functionality
We have issues without this, as soundwire bus would return error on
runtime pm get/set. For RFC, I had to make this dummy, I will be able to
add and test some code in next 1/2 spins.
Thanks,
srini
