On 9/9/2019 4:02 AM, Vitaly Gaiduk wrote:
> This patch adds ability to switch beetween two PHY SGMII modes.
> Some hardware, for example, FPGA IP designs may use 6-wire mode
> which enables differential SGMII clock to MAC.
>
> Signed-off-by: Vitaly Gaiduk <[email protected]>
> ---
> Changes in v2:
> - changed variable sgmii_type name to sgmii_ref_clk_en
>
> drivers/net/phy/dp83867.c | 16 ++++++++++++++++
> 1 file changed, 16 insertions(+)
>
> diff --git a/drivers/net/phy/dp83867.c b/drivers/net/phy/dp83867.c
> index 1f1ecee..cd6260e 100644
> --- a/drivers/net/phy/dp83867.c
> +++ b/drivers/net/phy/dp83867.c
> @@ -37,6 +37,7 @@
> #define DP83867_STRAP_STS2 0x006f
> #define DP83867_RGMIIDCTL 0x0086
> #define DP83867_IO_MUX_CFG 0x0170
> +#define DP83867_SGMIICTL 0x00D3
> #define DP83867_10M_SGMII_CFG 0x016F
> #define DP83867_10M_SGMII_RATE_ADAPT_MASK BIT(7)
>
> @@ -61,6 +62,9 @@
> #define DP83867_RGMII_TX_CLK_DELAY_EN BIT(1)
> #define DP83867_RGMII_RX_CLK_DELAY_EN BIT(0)
>
> +/* SGMIICTL bits */
> +#define DP83867_SGMII_TYPE BIT(14)
> +
> /* STRAP_STS1 bits */
> #define DP83867_STRAP_STS1_RESERVED BIT(11)
>
> @@ -109,6 +113,7 @@ struct dp83867_private {
> bool rxctrl_strap_quirk;
> bool set_clk_output;
> u32 clk_output_sel;
> + bool sgmii_ref_clk_en;
> };
>
> static int dp83867_ack_interrupt(struct phy_device *phydev)
> @@ -197,6 +202,9 @@ static int dp83867_of_init(struct phy_device *phydev)
> dp83867->rxctrl_strap_quirk = of_property_read_bool(of_node,
> "ti,dp83867-rxctrl-strap-quirk");
>
> + dp83867->sgmii_ref_clk_en = of_property_read_bool(of_node,
> + "ti,sgmii-ref-clock-output-enable");
> +
> /* Existing behavior was to use default pin strapping delay in rgmii
> * mode, but rgmii should have meant no delay. Warn existing users.
> */
> @@ -389,6 +397,14 @@ static int dp83867_config_init(struct phy_device *phydev)
>
> if (ret)
> return ret;
> +
> + /* SGMII type is set to 4-wire mode by default */
> + if (dp83867->sgmii_ref_clk_en) {
> + /* Switch on 6-wire mode */
> + val = phy_read_mmd(phydev, DP83867_DEVADDR,
> DP83867_SGMIICTL);
> + val |= DP83867_SGMII_TYPE;
> + phy_write_mmd(phydev, DP83867_DEVADDR,
> DP83867_SGMIICTL, val);
> + }
Is there a case where the value could be retained across a power
on/reset cycle and you would want to make sure you do write the intended
"wire mode" here? What I am suggesting is just changing this into a:
val = phy_read_mmd(phydev, DP83867_DEVADDR, DP83867_SGMIICTL);
if (dp83867->sgmii_ref_clk_en)
val |= DP83867_SGMII_TYPE;
else
val &= ~DP83867_SGMII_TYPE;
phy_write_mmd(phydev, DP83867_DEVADDR, DP83867_SGMIICTL, val);
Other than that, LGTM
--
Florian
