On Tue, 15 Oct 2019 23:51:22 -0300 Marcelo Schmitt <marcelo.schmi...@gmail.com> wrote:
> The AD7292 is a 10-bit monitor and control system with ADC, DACs, > temperature sensor, and GPIOs. > > Configure AD7292 devices in direct access mode, enabling single-ended > ADC readings. > > Datasheet: > Link: > https://www.analog.com/media/en/technical-documentation/data-sheets/ad7292.pdf > > Signed-off-by: Marcelo Schmitt <marcelo.schmi...@gmail.com> This looks fine to me. Assuming nothing else comes up, I'll pick this up once the binding was tidied up. Thanks, Jonathan > --- > MAINTAINERS | 7 + > drivers/iio/adc/Kconfig | 10 ++ > drivers/iio/adc/Makefile | 1 + > drivers/iio/adc/ad7292.c | 350 +++++++++++++++++++++++++++++++++++++++ > 4 files changed, 368 insertions(+) > create mode 100644 drivers/iio/adc/ad7292.c > > diff --git a/MAINTAINERS b/MAINTAINERS > index 32bf5f8116d0..e78317a5f4f1 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -813,6 +813,13 @@ S: Supported > F: drivers/iio/adc/ad7124.c > F: Documentation/devicetree/bindings/iio/adc/adi,ad7124.txt > > +ANALOG DEVICES INC AD7292 DRIVER > +M: Marcelo Schmitt <marcelo.schmi...@gmail.com> > +L: linux-...@vger.kernel.org > +W: http://ez.analog.com/community/linux-device-drivers > +S: Supported > +F: drivers/iio/adc/ad7292.c > + > ANALOG DEVICES INC AD7606 DRIVER > M: Stefan Popa <stefan.p...@analog.com> > L: linux-...@vger.kernel.org > diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig > index 632b331429c6..02587c990cb5 100644 > --- a/drivers/iio/adc/Kconfig > +++ b/drivers/iio/adc/Kconfig > @@ -59,6 +59,16 @@ config AD7291 > To compile this driver as a module, choose M here: the > module will be called ad7291. > > +config AD7292 > + tristate "Analog Devices AD7292 ADC driver" > + depends on SPI > + help > + Say yes here to build support for Analog Devices AD7292 > + 8 Channel ADC with temperature sensor. > + > + To compile this driver as a module, choose M here: the > + module will be called ad7292. > + > config AD7298 > tristate "Analog Devices AD7298 ADC driver" > depends on SPI > diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile > index 4779ab3ff8fb..1818f2f66566 100644 > --- a/drivers/iio/adc/Makefile > +++ b/drivers/iio/adc/Makefile > @@ -11,6 +11,7 @@ obj-$(CONFIG_AD7124) += ad7124.o > obj-$(CONFIG_AD7173) += ad7173.o > obj-$(CONFIG_AD7266) += ad7266.o > obj-$(CONFIG_AD7291) += ad7291.o > +obj-$(CONFIG_AD7292) += ad7292.o > obj-$(CONFIG_AD7298) += ad7298.o > obj-$(CONFIG_AD738X) += ad738x.o > obj-$(CONFIG_AD7768) += ad7768-1.o > diff --git a/drivers/iio/adc/ad7292.c b/drivers/iio/adc/ad7292.c > new file mode 100644 > index 000000000000..d90c7af8f6c2 > --- /dev/null > +++ b/drivers/iio/adc/ad7292.c > @@ -0,0 +1,350 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Analog Devices AD7292 SPI ADC driver > + * > + * Copyright 2019 Analog Devices Inc. > + */ > + > +#include <linux/bitfield.h> > +#include <linux/device.h> > +#include <linux/module.h> > +#include <linux/regulator/consumer.h> > +#include <linux/spi/spi.h> > + > +#include <linux/iio/iio.h> > + > +#define ADI_VENDOR_ID 0x0018 > + > +/* AD7292 registers definition */ > +#define AD7292_REG_VENDOR_ID 0x00 > +#define AD7292_REG_CONF_BANK 0x05 > +#define AD7292_REG_CONV_COMM 0x0E > +#define AD7292_REG_ADC_CH(x) (0x10 + (x)) > + > +/* AD7292 configuration bank subregisters definition */ > +#define AD7292_BANK_REG_VIN_RNG0 0x10 > +#define AD7292_BANK_REG_VIN_RNG1 0x11 > +#define AD7292_BANK_REG_SAMP_MODE 0x12 > + > +#define AD7292_RD_FLAG_MSK(x) (BIT(7) | ((x) & 0x3F)) > + > +/* AD7292_REG_ADC_CONVERSION */ > +#define AD7292_ADC_DATA_MASK GENMASK(15, 6) > +#define AD7292_ADC_DATA(x) FIELD_GET(AD7292_ADC_DATA_MASK, x) > + > +/* AD7292_CHANNEL_SAMPLING_MODE */ > +#define AD7292_CH_SAMP_MODE(reg, ch) ((reg >> 8) & BIT(ch)) > + > +/* AD7292_CHANNEL_VIN_RANGE */ > +#define AD7292_CH_VIN_RANGE(reg, ch) (reg & BIT(ch)) > + > +#define AD7291_VOLTAGE_CHAN(_chan) \ > +{ \ > + .type = IIO_VOLTAGE, \ > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \ > + BIT(IIO_CHAN_INFO_SCALE), \ > + .indexed = 1, \ > + .channel = _chan, \ > +} > + > +static const struct iio_chan_spec ad7292_channels[] = { > + AD7291_VOLTAGE_CHAN(0), > + AD7291_VOLTAGE_CHAN(1), > + AD7291_VOLTAGE_CHAN(2), > + AD7291_VOLTAGE_CHAN(3), > + AD7291_VOLTAGE_CHAN(4), > + AD7291_VOLTAGE_CHAN(5), > + AD7291_VOLTAGE_CHAN(6), > + AD7291_VOLTAGE_CHAN(7) > +}; > + > +static const struct iio_chan_spec ad7292_channels_diff[] = { > + { > + .type = IIO_VOLTAGE, > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), > + .indexed = 1, > + .differential = 1, > + .channel = 0, > + .channel2 = 1, > + }, > + AD7291_VOLTAGE_CHAN(2), > + AD7291_VOLTAGE_CHAN(3), > + AD7291_VOLTAGE_CHAN(4), > + AD7291_VOLTAGE_CHAN(5), > + AD7291_VOLTAGE_CHAN(6), > + AD7291_VOLTAGE_CHAN(7) > +}; > + > +struct ad7292_state { > + struct spi_device *spi; > + struct regulator *reg; > + unsigned short vref_mv; > + > + __be16 d16 ____cacheline_aligned; > + u8 d8[2]; > +}; > + > +static int ad7292_spi_reg_read(struct ad7292_state *st, unsigned int addr) > +{ > + int ret; > + > + st->d8[0] = AD7292_RD_FLAG_MSK(addr); > + > + ret = spi_write_then_read(st->spi, st->d8, 1, &st->d16, 2); > + if (ret < 0) > + return ret; > + > + return be16_to_cpu(st->d16); > +} > + > +static int ad7292_spi_subreg_read(struct ad7292_state *st, unsigned int addr, > + unsigned int sub_addr, unsigned int len) > +{ > + unsigned int shift = 16 - (8 * len); > + int ret; > + > + st->d8[0] = AD7292_RD_FLAG_MSK(addr); > + st->d8[1] = sub_addr; > + > + ret = spi_write_then_read(st->spi, st->d8, 2, &st->d16, len); > + if (ret < 0) > + return ret; > + > + return (be16_to_cpu(st->d16) >> shift); > +} > + > +static int ad7292_single_conversion(struct ad7292_state *st, > + unsigned int chan_addr) > +{ > + int ret; > + > + struct spi_transfer t[] = { > + { > + .tx_buf = &st->d8, > + .len = 4, > + .delay_usecs = 6, > + }, { > + .rx_buf = &st->d16, > + .len = 2, > + }, > + }; > + > + st->d8[0] = chan_addr; > + st->d8[1] = AD7292_RD_FLAG_MSK(AD7292_REG_CONV_COMM); > + > + ret = spi_sync_transfer(st->spi, t, ARRAY_SIZE(t)); > + > + if (ret < 0) > + return ret; > + > + return be16_to_cpu(st->d16); > +} > + > +static int ad7292_vin_range_multiplier(struct ad7292_state *st, int channel) > +{ > + int samp_mode, range0, range1, factor = 1; > + > + /* > + * Every AD7292 ADC channel may have its input range adjusted according > + * to the settings at the ADC sampling mode and VIN range subregisters. > + * For a given channel, the minimum input range is equal to Vref, and it > + * may be increased by a multiplier factor of 2 or 4 according to the > + * following rule: > + * If channel is being sampled wiht respect to AGND: > + * factor = 4 if VIN range0 and VIN range1 equal 0 > + * factor = 2 if only one of VIN ranges equal 1 > + * factor = 1 if both VIN range0 and VIN range1 equal 1 > + * If channel is being sampled with respect to AVDD: > + * factor = 4 if VIN range0 and VIN range1 equal 0 > + * Behavior is undefined if any of VIN range doesn't equal 0 > + */ > + > + samp_mode = ad7292_spi_subreg_read(st, AD7292_REG_CONF_BANK, > + AD7292_BANK_REG_SAMP_MODE, 2); > + > + if (samp_mode < 0) > + return samp_mode; > + > + range0 = ad7292_spi_subreg_read(st, AD7292_REG_CONF_BANK, > + AD7292_BANK_REG_VIN_RNG0, 2); > + > + if (range0 < 0) > + return range0; > + > + range1 = ad7292_spi_subreg_read(st, AD7292_REG_CONF_BANK, > + AD7292_BANK_REG_VIN_RNG1, 2); > + > + if (range1 < 0) > + return range1; > + > + if (AD7292_CH_SAMP_MODE(samp_mode, channel)) { > + /* Sampling with respect to AGND */ > + if (!AD7292_CH_VIN_RANGE(range0, channel)) > + factor *= 2; > + > + if (!AD7292_CH_VIN_RANGE(range1, channel)) > + factor *= 2; > + > + } else { > + /* Sampling with respect to AVDD */ > + if (AD7292_CH_VIN_RANGE(range0, channel) || > + AD7292_CH_VIN_RANGE(range1, channel)) > + return -EPERM; > + > + factor = 4; > + } > + > + return factor; > +} > + > +static int ad7292_read_raw(struct iio_dev *indio_dev, > + const struct iio_chan_spec *chan, > + int *val, int *val2, long info) > +{ > + struct ad7292_state *st = iio_priv(indio_dev); > + unsigned int ch_addr; > + int ret; > + > + switch (info) { > + case IIO_CHAN_INFO_RAW: > + ch_addr = AD7292_REG_ADC_CH(chan->channel); > + ret = ad7292_single_conversion(st, ch_addr); > + if (ret < 0) > + return ret; > + > + *val = AD7292_ADC_DATA(ret); > + > + return IIO_VAL_INT; > + case IIO_CHAN_INFO_SCALE: > + /* > + * To convert a raw value to standard units, the IIO defines > + * this formula: Scaled value = (raw + offset) * scale. > + * For the scale to be a correct multiplier for (raw + offset), > + * it must be calculated as the input range divided by the > + * number of possible distinct input values. Given the ADC data > + * is 10 bit long, it may assume 2^10 distinct values. > + * Hence, scale = range / 2^10. The IIO_VAL_FRACTIONAL_LOG2 > + * return type indicates to the IIO API to divide *val by 2 to > + * the power of *val2 when returning from read_raw. > + */ > + > + ret = ad7292_vin_range_multiplier(st, chan->channel); > + if (ret < 0) > + return ret; > + > + *val = st->vref_mv * ret; > + *val2 = 10; > + return IIO_VAL_FRACTIONAL_LOG2; > + default: > + break; > + } > + return -EINVAL; > +} > + > +static const struct iio_info ad7292_info = { > + .read_raw = ad7292_read_raw, > +}; > + > +static void ad7292_regulator_disable(void *data) > +{ > + struct ad7292_state *st = data; > + > + regulator_disable(st->reg); > +} > + > +static int ad7292_probe(struct spi_device *spi) > +{ > + struct ad7292_state *st; > + struct iio_dev *indio_dev; > + struct device_node *child; > + bool diff_channels = 0; > + int ret; > + > + indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st)); > + if (!indio_dev) > + return -ENOMEM; > + > + st = iio_priv(indio_dev); > + st->spi = spi; > + > + ret = ad7292_spi_reg_read(st, AD7292_REG_VENDOR_ID); > + if (ret != ADI_VENDOR_ID) { > + dev_err(&spi->dev, "Wrong vendor id 0x%x\n", ret); > + return -EINVAL; > + } > + > + spi_set_drvdata(spi, indio_dev); > + > + st->reg = devm_regulator_get_optional(&spi->dev, "vref"); > + if (!IS_ERR(st->reg)) { > + ret = regulator_enable(st->reg); > + if (ret) { > + dev_err(&spi->dev, > + "Failed to enable external vref supply\n"); > + return ret; > + } > + > + ret = devm_add_action_or_reset(&spi->dev, > + ad7292_regulator_disable, st); > + if (ret) { > + regulator_disable(st->reg); > + return ret; > + } > + > + ret = regulator_get_voltage(st->reg); > + if (ret < 0) > + return ret; > + > + st->vref_mv = ret / 1000; > + } else { > + /* Use the internal voltage reference. */ > + st->vref_mv = 1250; > + } > + > + indio_dev->dev.parent = &spi->dev; > + indio_dev->name = spi_get_device_id(spi)->name; > + indio_dev->modes = INDIO_DIRECT_MODE; > + indio_dev->info = &ad7292_info; > + > + for_each_available_child_of_node(spi->dev.of_node, child) { > + diff_channels = of_property_read_bool(child, "diff-channels"); > + if (diff_channels) > + break; > + } > + > + if (diff_channels) { > + indio_dev->num_channels = ARRAY_SIZE(ad7292_channels_diff); > + indio_dev->channels = ad7292_channels_diff; > + } else { > + indio_dev->num_channels = ARRAY_SIZE(ad7292_channels); > + indio_dev->channels = ad7292_channels; > + } > + > + return devm_iio_device_register(&spi->dev, indio_dev); > +} > + > +static const struct spi_device_id ad7292_id_table[] = { > + { "ad7292", 0 }, > + {} > +}; > +MODULE_DEVICE_TABLE(spi, ad7292_id_table); > + > +static const struct of_device_id ad7292_of_match[] = { > + { .compatible = "adi,ad7292" }, > + { }, > +}; > +MODULE_DEVICE_TABLE(of, ad7292_of_match); > + > +static struct spi_driver ad7292_driver = { > + .driver = { > + .name = "ad7292", > + .of_match_table = ad7292_of_match, > + }, > + .probe = ad7292_probe, > + .id_table = ad7292_id_table, > +}; > +module_spi_driver(ad7292_driver); > + > +MODULE_AUTHOR("Marcelo Schmitt <marcelo.schmi...@gmail.com>"); > +MODULE_DESCRIPTION("Analog Devices AD7292 ADC driver"); > +MODULE_LICENSE("GPL v2");
