The Smart Voltage Scaling(SVS) engine is a piece of hardware
which has several controllers(banks) for calculating suitable
voltage to different power domains(CPU/GPU/CCI) according to
chip process corner, temperatures and other factors. Then DVFS
driver could apply SVS bank voltage to PMIC/Buck.
Signed-off-by: Roger Lu <roger...@mediatek.com>
---
drivers/power/avs/Kconfig | 10 +
drivers/power/avs/Makefile | 1 +
drivers/power/avs/mtk_svs.c | 1858 +++++++++++++++++++++++++++++++++
include/linux/power/mtk_svs.h | 23 +
4 files changed, 1892 insertions(+)
create mode 100644 drivers/power/avs/mtk_svs.c
create mode 100644 include/linux/power/mtk_svs.h
diff --git a/drivers/power/avs/Kconfig b/drivers/power/avs/Kconfig
index cdb4237bfd02..754e9315c4ea 100644
--- a/drivers/power/avs/Kconfig
+++ b/drivers/power/avs/Kconfig
@@ -35,3 +35,13 @@ config ROCKCHIP_IODOMAIN
Say y here to enable support io domains on Rockchip SoCs. It is
necessary for the io domain setting of the SoC to match the
voltage supplied by the regulators.
+
+config MTK_SVS
+ tristate "MediaTek Smart Voltage Scaling(SVS)"
+ depends on POWER_AVS && MTK_EFUSE && NVMEM
+ help
+ The Smart Voltage Scaling(SVS) engine is a piece of hardware
+ which has several controllers(banks) for calculating suitable
+ voltage to different power domains(CPU/GPU/CCI) according to
+ chip process corner, temperatures and other factors. Then DVFS
+ driver could apply SVS bank voltage to PMIC/Buck.
diff --git a/drivers/power/avs/Makefile b/drivers/power/avs/Makefile
index 9007d05853e2..231adf078582 100644
--- a/drivers/power/avs/Makefile
+++ b/drivers/power/avs/Makefile
@@ -2,3 +2,4 @@
obj-$(CONFIG_POWER_AVS_OMAP) += smartreflex.o
obj-$(CONFIG_QCOM_CPR) += qcom-cpr.o
obj-$(CONFIG_ROCKCHIP_IODOMAIN) += rockchip-io-domain.o
+obj-$(CONFIG_MTK_SVS) += mtk_svs.o
diff --git a/drivers/power/avs/mtk_svs.c b/drivers/power/avs/mtk_svs.c
new file mode 100644
index 000000000000..3e26191f6a3b
--- /dev/null
+++ b/drivers/power/avs/mtk_svs.c
@@ -0,0 +1,1858 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 MediaTek Inc.
+ */
+
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/kthread.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/pm_domain.h>
+#include <linux/pm_opp.h>
+#include <linux/pm_qos.h>
+#include <linux/pm_runtime.h>
+#include <linux/power/mtk_svs.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/thermal.h>
+
+/* svs bank 1-line sw id */
+#define SVSB_CPU_LITTLE BIT(0)
+#define SVSB_CPU_BIG BIT(1)
+#define SVSB_CCI BIT(2)
+#define SVSB_GPU BIT(3)
+
+/* svs bank mode support */
+#define SVSB_MODE_ALL_DISABLE (0)
+#define SVSB_MODE_INIT01 BIT(1)
+#define SVSB_MODE_INIT02 BIT(2)
+#define SVSB_MODE_MON BIT(3)
+
+/* svs bank init01 condition */
+#define SVSB_INIT01_VOLT_IGNORE BIT(1)
+#define SVSB_INIT01_VOLT_INC_ONLY BIT(2)
+#define SVSB_INIT01_CLK_EN BIT(31)
+
+/* svs bank common setting */
+#define SVSB_TZONE_HIGH_TEMP_MAX (U32_MAX)
+#define SVSB_RUNCONFIG_DEFAULT (0x80000000)
+#define SVSB_DC_SIGNED_BIT (0x8000)
+#define SVSB_INTEN_INIT0x (0x00005f01)
+#define SVSB_INTEN_MONVOPEN (0x00ff0000)
+#define SVSB_EN_OFF (0x0)
+#define SVSB_EN_MASK (0x7)
+#define SVSB_EN_INIT01 (0x1)
+#define SVSB_EN_INIT02 (0x5)
+#define SVSB_EN_MON (0x2)
+#define SVSB_INTSTS_MONVOP (0x00ff0000)
+#define SVSB_INTSTS_COMPLETE (0x1)
+#define SVSB_INTSTS_CLEAN (0x00ffffff)
+
+static DEFINE_SPINLOCK(mtk_svs_lock);
+struct mtk_svs;
+
+/*
+ * enum svsb_phase - svs bank phase enumeration
+ * @SVSB_PHASE_INIT01: basic init for svs bank
+ * @SVSB_PHASE_INIT02: svs bank can provide voltages
+ * @SVSB_PHASE_MON: svs bank can provide voltages with thermal effect
+ * @SVSB_PHASE_ERROR: svs bank encouters unexpected condition
+ *
+ * Each svs bank has its own independent phase. We enable each svs bank by
+ * running their phase orderly. However, When svs bank ecnounters unexpected
+ * condition, it will fire an irq (PHASE_ERROR) to inform svs software.
+ *
+ * svs bank general phase-enabled order:
+ * SVSB_PHASE_INIT01 -> SVSB_PHASE_INIT02 -> SVSB_PHASE_MON
+ */
+enum svsb_phase {
+ SVSB_PHASE_INIT01 = 0,
+ SVSB_PHASE_INIT02,
+ SVSB_PHASE_MON,
+ SVSB_PHASE_ERROR,
+};
+
+enum svs_reg_index {
+ TEMPMONCTL0 = 0,
+ TEMPMONCTL1,
+ TEMPMONCTL2,
+ TEMPMONINT,
+ TEMPMONINTSTS,
+ TEMPMONIDET0,
+ TEMPMONIDET1,
+ TEMPMONIDET2,
+ TEMPH2NTHRE,
+ TEMPHTHRE,
+ TEMPCTHRE,
+ TEMPOFFSETH,
+ TEMPOFFSETL,
+ TEMPMSRCTL0,
+ TEMPMSRCTL1,
+ TEMPAHBPOLL,
+ TEMPAHBTO,
+ TEMPADCPNP0,
+ TEMPADCPNP1,
+ TEMPADCPNP2,
+ TEMPADCMUX,
+ TEMPADCEXT,
+ TEMPADCEXT1,
+ TEMPADCEN,
+ TEMPPNPMUXADDR,
+ TEMPADCMUXADDR,
+ TEMPADCEXTADDR,
+ TEMPADCEXT1ADDR,
+ TEMPADCENADDR,
+ TEMPADCVALIDADDR,
+ TEMPADCVOLTADDR,
+ TEMPRDCTRL,
+ TEMPADCVALIDMASK,
+ TEMPADCVOLTAGESHIFT,
+ TEMPADCWRITECTRL,
+ TEMPMSR0,
+ TEMPMSR1,
+ TEMPMSR2,
+ TEMPADCHADDR,
+ TEMPIMMD0,
+ TEMPIMMD1,
+ TEMPIMMD2,
+ TEMPMONIDET3,
+ TEMPADCPNP3,
+ TEMPMSR3,
+ TEMPIMMD3,
+ TEMPPROTCTL,
+ TEMPPROTTA,
+ TEMPPROTTB,
+ TEMPPROTTC,
+ TEMPSPARE0,
+ TEMPSPARE1,
+ TEMPSPARE2,
+ TEMPSPARE3,
+ TEMPMSR0_1,
+ TEMPMSR1_1,
+ TEMPMSR2_1,
+ TEMPMSR3_1,
+ DESCHAR,
+ TEMPCHAR,
+ DETCHAR,
+ AGECHAR,
+ DCCONFIG,
+ AGECONFIG,
+ FREQPCT30,
+ FREQPCT74,
+ LIMITVALS,
+ VBOOT,
+ DETWINDOW,
+ CONFIG,
+ TSCALCS,
+ RUNCONFIG,
+ SVSEN,
+ INIT2VALS,
+ DCVALUES,
+ AGEVALUES,
+ VOP30,
+ VOP74,
+ TEMP,
+ INTSTS,
+ INTSTSRAW,
+ INTEN,
+ CHKINT,
+ CHKSHIFT,
+ STATUS,
+ VDESIGN30,
+ VDESIGN74,
+ DVT30,
+ DVT74,
+ AGECOUNT,
+ SMSTATE0,
+ SMSTATE1,
+ CTL0,
+ DESDETSEC,
+ TEMPAGESEC,
+ CTRLSPARE0,
+ CTRLSPARE1,
+ CTRLSPARE2,
+ CTRLSPARE3,
+ CORESEL,
+ THERMINTST,
+ INTST,
+ THSTAGE0ST,
+ THSTAGE1ST,
+ THSTAGE2ST,
+ THAHBST0,
+ THAHBST1,
+ SPARE0,
+ SPARE1,
+ SPARE2,
+ SPARE3,
+ THSLPEVEB,
+ reg_num,
+};
+
+static const u32 svs_regs_v2[] = {
+ [TEMPMONCTL0] = 0x000,
+ [TEMPMONCTL1] = 0x004,
+ [TEMPMONCTL2] = 0x008,
+ [TEMPMONINT] = 0x00c,
+ [TEMPMONINTSTS] = 0x010,
+ [TEMPMONIDET0] = 0x014,
+ [TEMPMONIDET1] = 0x018,
+ [TEMPMONIDET2] = 0x01c,
+ [TEMPH2NTHRE] = 0x024,
+ [TEMPHTHRE] = 0x028,
+ [TEMPCTHRE] = 0x02c,
+ [TEMPOFFSETH] = 0x030,
+ [TEMPOFFSETL] = 0x034,
+ [TEMPMSRCTL0] = 0x038,
+ [TEMPMSRCTL1] = 0x03c,
+ [TEMPAHBPOLL] = 0x040,
+ [TEMPAHBTO] = 0x044,
+ [TEMPADCPNP0] = 0x048,
+ [TEMPADCPNP1] = 0x04c,
+ [TEMPADCPNP2] = 0x050,
+ [TEMPADCMUX] = 0x054,
+ [TEMPADCEXT] = 0x058,
+ [TEMPADCEXT1] = 0x05c,
+ [TEMPADCEN] = 0x060,
+ [TEMPPNPMUXADDR] = 0x064,
+ [TEMPADCMUXADDR] = 0x068,
+ [TEMPADCEXTADDR] = 0x06c,
+ [TEMPADCEXT1ADDR] = 0x070,
+ [TEMPADCENADDR] = 0x074,
+ [TEMPADCVALIDADDR] = 0x078,
+ [TEMPADCVOLTADDR] = 0x07c,
+ [TEMPRDCTRL] = 0x080,
+ [TEMPADCVALIDMASK] = 0x084,
+ [TEMPADCVOLTAGESHIFT] = 0x088,
+ [TEMPADCWRITECTRL] = 0x08c,
+ [TEMPMSR0] = 0x090,
+ [TEMPMSR1] = 0x094,
+ [TEMPMSR2] = 0x098,
+ [TEMPADCHADDR] = 0x09c,
+ [TEMPIMMD0] = 0x0a0,
+ [TEMPIMMD1] = 0x0a4,
+ [TEMPIMMD2] = 0x0a8,
+ [TEMPMONIDET3] = 0x0b0,
+ [TEMPADCPNP3] = 0x0b4,
+ [TEMPMSR3] = 0x0b8,
+ [TEMPIMMD3] = 0x0bc,
+ [TEMPPROTCTL] = 0x0c0,
+ [TEMPPROTTA] = 0x0c4,
+ [TEMPPROTTB] = 0x0c8,
+ [TEMPPROTTC] = 0x0cc,
+ [TEMPSPARE0] = 0x0f0,
+ [TEMPSPARE1] = 0x0f4,
+ [TEMPSPARE2] = 0x0f8,
+ [TEMPSPARE3] = 0x0fc,
+ [TEMPMSR0_1] = 0x190,
+ [TEMPMSR1_1] = 0x194,
+ [TEMPMSR2_1] = 0x198,
+ [TEMPMSR3_1] = 0x1b8,
+ [DESCHAR] = 0xc00,
+ [TEMPCHAR] = 0xc04,
+ [DETCHAR] = 0xc08,
+ [AGECHAR] = 0xc0c,
+ [DCCONFIG] = 0xc10,
+ [AGECONFIG] = 0xc14,
+ [FREQPCT30] = 0xc18,
+ [FREQPCT74] = 0xc1c,
+ [LIMITVALS] = 0xc20,
+ [VBOOT] = 0xc24,
+ [DETWINDOW] = 0xc28,
+ [CONFIG] = 0xc2c,
+ [TSCALCS] = 0xc30,
+ [RUNCONFIG] = 0xc34,
+ [SVSEN] = 0xc38,
+ [INIT2VALS] = 0xc3c,
+ [DCVALUES] = 0xc40,
+ [AGEVALUES] = 0xc44,
+ [VOP30] = 0xc48,
+ [VOP74] = 0xc4c,
+ [TEMP] = 0xc50,
+ [INTSTS] = 0xc54,
+ [INTSTSRAW] = 0xc58,
+ [INTEN] = 0xc5c,
+ [CHKINT] = 0xc60,
+ [CHKSHIFT] = 0xc64,
+ [STATUS] = 0xc68,
+ [VDESIGN30] = 0xc6c,
+ [VDESIGN74] = 0xc70,
+ [DVT30] = 0xc74,
+ [DVT74] = 0xc78,
+ [AGECOUNT] = 0xc7c,
+ [SMSTATE0] = 0xc80,
+ [SMSTATE1] = 0xc84,
+ [CTL0] = 0xc88,
+ [DESDETSEC] = 0xce0,
+ [TEMPAGESEC] = 0xce4,
+ [CTRLSPARE0] = 0xcf0,
+ [CTRLSPARE1] = 0xcf4,
+ [CTRLSPARE2] = 0xcf8,
+ [CTRLSPARE3] = 0xcfc,
+ [CORESEL] = 0xf00,
+ [THERMINTST] = 0xf04,
+ [INTST] = 0xf08,
+ [THSTAGE0ST] = 0xf0c,
+ [THSTAGE1ST] = 0xf10,
+ [THSTAGE2ST] = 0xf14,
+ [THAHBST0] = 0xf18,
+ [THAHBST1] = 0xf1c,
+ [SPARE0] = 0xf20,
+ [SPARE1] = 0xf24,
+ [SPARE2] = 0xf28,
+ [SPARE3] = 0xf2c,
+ [THSLPEVEB] = 0xf30,
+};
+
+/*
+ * struct thermal_parameter - This is for storing thermal efuse data.
+ * We cacluate thermal efuse data to produce "mts" and "bts" for
+ * svs bank mon mode.
+ */
+struct thermal_parameter {
+ int adc_ge_t;
+ int adc_oe_t;
+ int ge;
+ int oe;
+ int gain;
+ int o_vtsabb;
+ int o_vtsmcu1;
+ int o_vtsmcu2;
+ int o_vtsmcu3;
+ int o_vtsmcu4;
+ int o_vtsmcu5;
+ int degc_cali;
+ int adc_cali_en_t;
+ int o_slope;
+ int o_slope_sign;
+ int ts_id;
+};
+
+/*
+ * struct svs_bank - svs bank representation
+ * @dev: bank device for opp table/mtcmos/buck control
+ * @init_completion: the timeout completion for bank init
+ * @buck: phandle of the regulator
+ * @lock: mutex lock to protect voltage update process
+ * @suspended: suspend flag of this bank
+ * @mtcmos_request: bank's power-domain on request
+ * @volt_offset: bank voltage offset controlled by svs software
+ * @mode_support: bank mode support.
+ * @opp_freqs: signed-off frequencies from default opp table
+ * @opp_volts: signed-off voltages from default opp table
+ * @freqs_pct: percent of "opp_freqs / freq_base" for bank init
+ * @volts: bank voltages
+ * @freq_base: reference frequency for bank init
+ * @vboot: voltage request for bank init01 stage only
+ * @volt_step: bank voltage step
+ * @volt_base: bank voltage base
+ * @init01_volt_flag: bank init01 voltage flag
+ * @phase: bank current phase
+ * @vmax: bank voltage maximum
+ * @vmin: bank votlage minimum
+ * @temp: bank temperature
+ * @temp_upper_bound: bank temperature upper bound
+ * @temp_lower_bound: bank temperature lower bound
+ * @tzone_high_temp: thermal zone high temperature threshold
+ * @tzone_high_temp_offset: thermal zone high temperature offset
+ * @tzone_low_temp: thermal zone low temperature threshold
+ * @tzone_low_temp_offset: thermal zone low temperature offset
+ * @core_sel: bank selection
+ * @opp_count: bank opp count
+ * @int_st: bank interrupt identification
+ * @sw_id: bank software identification
+ * @ctl0: bank thermal sensor selection
+ * @of_compatible: of_compatible string of bank
+ * @name: bank name
+ * @tzone_name: thermal zone name
+ * @buck_name: regulator name
+ *
+ * Other structure members which are not listed above are svs platform
+ * efuse data for bank init
+ */
+struct svs_bank {
+ struct device *dev;
+ struct completion init_completion;
+ struct regulator *buck;
+ struct mutex lock; /* lock to protect voltage update process */
+ bool suspended;
+ bool mtcmos_request;
+ s32 volt_offset;
+ u32 mode_support;
+ u32 opp_freqs[16];
+ u32 opp_volts[16];
+ u32 freqs_pct[16];
+ u32 volts[16];
+ u32 freq_base;
+ u32 vboot;
+ u32 volt_step;
+ u32 volt_base;
+ u32 init01_volt_flag;
+ u32 phase;
+ u32 vmax;
+ u32 vmin;
+ u32 bts;
+ u32 mts;
+ u32 bdes;
+ u32 mdes;
+ u32 mtdes;
+ u32 dcbdet;
+ u32 dcmdet;
+ u32 dthi;
+ u32 dtlo;
+ u32 det_window;
+ u32 det_max;
+ u32 age_config;
+ u32 age_voffset_in;
+ u32 agem;
+ u32 dc_config;
+ u32 dc_voffset_in;
+ u32 dvt_fixed;
+ u32 vco;
+ u32 chk_shift;
+ u32 temp;
+ u32 temp_upper_bound;
+ u32 temp_lower_bound;
+ u32 tzone_high_temp;
+ u32 tzone_high_temp_offset;
+ u32 tzone_low_temp;
+ u32 tzone_low_temp_offset;
+ u32 core_sel;
+ u32 opp_count;
+ u32 int_st;
+ u32 sw_id;
+ u32 ctl0;
+ u8 *of_compatible;
+ u8 *name;
+ u8 *tzone_name;
+ u8 *buck_name;
+};
+
+/*
+ * struct svs_platform - svs platform data
+ * @banks: phandle of the banks that support
+ * @efuse_parsing: phandle of efuse parsing function
+ * @set_freqs_pct: phandle of set frequencies percent function
+ * @get_vops: phandle of get bank voltages function
+ * @irqflags: irq settings flags
+ * @fake_efuse: the flag for running svs with fake efuse
+ * @need_hw_reset: the flag for reset svs HW when system suspend
+ * @regs: phandle to the registers map
+ * @bank_num: the total number of banks
+ * @efuse_check: the svs efuse check index
+ * @suppliers: the devices which needs to be probed first
+ * @name: svs platform name
+ *
+ * svs platorm data will be instanced with const flag and stored
+ * as data memeber in struct of_device_id.
+ */
+struct svs_platform {
+ struct svs_bank *banks;
+ bool (*efuse_parsing)(struct mtk_svs *svs);
+ void (*set_freqs_pct)(struct mtk_svs *svs);
+ void (*get_vops)(struct mtk_svs *svs);
+ unsigned long irqflags;
+ bool fake_efuse;
+ bool need_hw_reset;
+ const u32 *regs;
+ u32 bank_num;
+ u32 efuse_check;
+ u8 *suppliers[2];
+ u8 *name;
+};
+
+/*
+ * struct mtk_svs - generic svs
+ * @svs_platform: phandle of svs platform data
+ * @pbank: phandle of svs bank whose register is going be updated
+ * @dev: svs platform device
+ * @base: svs platform register address base
+ * @main_clk: main clock for svs bank
+ * @efuse_num: the total number of svs platform efuse
+ * @thermal_efuse_num: the total number of thermal efuse
+ * @efuse: svs platform efuse data received from NVMEM framework
+ * @thermal_efuse: thermal efuse data received from NVMEM framework
+ *
+ * This generic svs helps retrieve different svs platform resource
+ * from dts and has a phandle to a svs bank for us to update its registers.
+ */
+struct mtk_svs {
+ const struct svs_platform *platform;
+ struct svs_bank *pbank;
+ struct device *dev;
+ void __iomem *base;
+ struct clk *main_clk;
+ size_t efuse_num;
+ size_t thermal_efuse_num;
+ u32 *efuse;
+ u32 *thermal_efuse;
+};
+
+unsigned long claim_mtk_svs_lock(void)
+ __acquires(&mtk_svs_lock)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&mtk_svs_lock, flags);
+
+ return flags;
+}
+EXPORT_SYMBOL_GPL(claim_mtk_svs_lock);
+
+void release_mtk_svs_lock(unsigned long flags)
+ __releases(&mtk_svs_lock)
+{
+ spin_unlock_irqrestore(&mtk_svs_lock, flags);
+}
+EXPORT_SYMBOL_GPL(release_mtk_svs_lock);
+
+static u32 percent(u32 numerator, u32 denominator)
+{
+ u32 pct;
+
+ /* If not divide 1000, "numerator * 100" will have data overflow. */
+ numerator /= 1000;
+ denominator /= 1000;
+ pct = ((numerator * 100) + denominator - 1) / denominator;
+ pct &= GENMASK(7, 0);
+
+ return pct;
+}
+
+static u32 svs_readl(struct mtk_svs *svs, enum svs_reg_index rg_i)
+{
+ return readl(svs->base + svs->platform->regs[rg_i]);
+}
+
+static void svs_writel(struct mtk_svs *svs, u32 val, enum svs_reg_index rg_i)
+{
+ writel(val, svs->base + svs->platform->regs[rg_i]);
+}
+
+static void svs_switch_bank(struct mtk_svs *svs)
+{
+ struct svs_bank *svsb = svs->pbank;
+
+ svs_writel(svs, svsb->core_sel, CORESEL);
+}
+
+static u32 svs_bank_volt_to_opp_volt(u32 svsb_volt, u32 svsb_volt_step,
+ u32 svsb_volt_base)
+{
+ u32 opp_u_volt;
+
+ opp_u_volt = (svsb_volt * svsb_volt_step) + svsb_volt_base;
+
+ return opp_u_volt;
+}
+
+static int svs_get_bank_zone_temperature(u8 *tzone_name, int *tzone_temp)
+{
+ struct thermal_zone_device *tzd;
+
+ tzd = thermal_zone_get_zone_by_name(tzone_name);
+ if (IS_ERR(tzd))
+ return PTR_ERR(tzd);
+
+ return thermal_zone_get_temp(tzd, tzone_temp);
+}
+
+static int svs_adjust_pm_opp_volts(struct svs_bank *svsb, bool force_update)
+{
+ u32 i, svsb_volt, opp_volt, temp_offset = 0;
+ int tzone_temp, ret = -EPERM;
+
+ mutex_lock(&svsb->lock);
+
+ /*
+ * If svs bank is suspended, it means signed-off voltages are applied.
+ * Don't need to update opp voltage anymore.
+ */
+ if (svsb->suspended && !force_update) {
+ dev_notice(svsb->dev, "bank is suspended\n");
+ ret = -EPERM;
+ goto unlock_mutex;
+ }
+
+ /* Get thermal effect */
+ if (svsb->phase == SVSB_PHASE_MON) {
+ if (svsb->temp > svsb->temp_upper_bound &&
+ svsb->temp < svsb->temp_lower_bound) {
+ dev_warn(svsb->dev, "svsb->temp = 0x%x, abnormal?\n",
+ svsb->temp);
+ ret = -EINVAL;
+ goto unlock_mutex;
+ }
+
+ ret = svs_get_bank_zone_temperature(svsb->tzone_name,
+ &tzone_temp);
+ if (ret) {
+ dev_err(svsb->dev, "no \"%s\" zone temperature(%d)?\n",
+ svsb->tzone_name, ret);
+ dev_err(svsb->dev, "set signed-off voltage instead\n");
+ svsb->phase = SVSB_PHASE_ERROR;
+ }
+
+ if (tzone_temp >= svsb->tzone_high_temp)
+ temp_offset += svsb->tzone_high_temp_offset;
+ else if (tzone_temp <= svsb->tzone_low_temp)
+ temp_offset += svsb->tzone_low_temp_offset;
+ }
+
+ /* vmin <= svsb_volt (opp_volt) <= signed-off voltage */
+ for (i = 0; i < svsb->opp_count; i++) {
+ if (svsb->phase == SVSB_PHASE_MON) {
+ svsb_volt = max((svsb->volts[i] + svsb->volt_offset +
+ temp_offset), svsb->vmin);
+ opp_volt = svs_bank_volt_to_opp_volt(svsb_volt,
+ svsb->volt_step,
+ svsb->volt_base);
+ } else if (svsb->phase == SVSB_PHASE_INIT02) {
+ svsb_volt = max((svsb->volts[i] + svsb->volt_offset),
+ svsb->vmin);
+ opp_volt = svs_bank_volt_to_opp_volt(svsb_volt,
+ svsb->volt_step,
+ svsb->volt_base);
+ } else if (svsb->phase == SVSB_PHASE_ERROR) {
+ opp_volt = svsb->opp_volts[i];
+ } else {
+ dev_err(svsb->dev, "unknown phase: %u?\n",
+ svsb->phase);
+ ret = -EINVAL;
+ goto unlock_mutex;
+ }
+
+ opp_volt = min(opp_volt, svsb->opp_volts[i]);
+ ret = dev_pm_opp_adjust_voltage(svsb->dev, svsb->opp_freqs[i],
+ opp_volt, opp_volt,
+ svsb->opp_volts[i]);
+ if (ret) {
+ dev_err(svsb->dev, "set voltage fail: %d\n", ret);
+ goto unlock_mutex;
+ }
+ }
+
+unlock_mutex:
+ mutex_unlock(&svsb->lock);
+
+ return ret;
+}
+
+static u32 interpolate(u32 f0, u32 f1, u32 v0, u32 v1, u32 fx)
+{
+ u32 vy;
+
+ if (v0 == v1 || f0 == f1)
+ return v0;
+
+ /* *100 to have decimal fraction factor, +99 for rounding up. */
+ vy = (v0 * 100) - ((((v0 - v1) * 100) / (f0 - f1)) * (f0 - fx));
+ vy = (vy + 99) / 100;
+
+ return vy;
+}
+
+static void svs_get_vops_v2(struct mtk_svs *svs)
+{
+ struct svs_bank *svsb = svs->pbank;
+ u32 temp, i;
+
+ temp = svs_readl(svs, VOP30);
+ svsb->volts[6] = (temp >> 24) & GENMASK(7, 0);
+ svsb->volts[4] = (temp >> 16) & GENMASK(7, 0);
+ svsb->volts[2] = (temp >> 8) & GENMASK(7, 0);
+ svsb->volts[0] = (temp & GENMASK(7, 0));
+
+ temp = svs_readl(svs, VOP74);
+ svsb->volts[14] = (temp >> 24) & GENMASK(7, 0);
+ svsb->volts[12] = (temp >> 16) & GENMASK(7, 0);
+ svsb->volts[10] = (temp >> 8) & GENMASK(7, 0);
+ svsb->volts[8] = (temp & GENMASK(7, 0));
+
+ for (i = 0; i <= 7; i++) {
+ if (i < 7) {
+ svsb->volts[(i * 2) + 1] =
+ interpolate(svsb->freqs_pct[i * 2],
+ svsb->freqs_pct[(i + 1) * 2],
+ svsb->volts[i * 2],
+ svsb->volts[(i + 1) * 2],
+ svsb->freqs_pct[(i * 2) + 1]);
+ } else if (i == 7) {
+ svsb->volts[(i * 2) + 1] =
+ interpolate(svsb->freqs_pct[(i - 1) * 2],
+ svsb->freqs_pct[i * 2],
+ svsb->volts[(i - 1) * 2],
+ svsb->volts[i * 2],
+ svsb->freqs_pct[(i * 2) + 1]);
+ }
+ }
+}
+
+static void svs_set_freqs_pct_v2(struct mtk_svs *svs)
+{
+ struct svs_bank *svsb = svs->pbank;
+
+ svs_writel(svs,
+ ((svsb->freqs_pct[6] << 24) & GENMASK(31, 24)) |
+ ((svsb->freqs_pct[4] << 16) & GENMASK(23, 16)) |
+ ((svsb->freqs_pct[2] << 8) & GENMASK(15, 8)) |
+ (svsb->freqs_pct[0] & GENMASK(7, 0)),
+ FREQPCT30);
+ svs_writel(svs,
+ ((svsb->freqs_pct[14] << 24) & GENMASK(31, 24)) |
+ ((svsb->freqs_pct[12] << 16) & GENMASK(23, 16)) |
+ ((svsb->freqs_pct[10] << 8) & GENMASK(15, 8)) |
+ ((svsb->freqs_pct[8]) & GENMASK(7, 0)),
+ FREQPCT74);
+}
+
+static void svs_set_bank_phase(struct mtk_svs *svs, u32 target_phase)
+{
+ const struct svs_platform *svsp = svs->platform;
+ struct svs_bank *svsb = svs->pbank;
+ u32 des_char, temp_char, det_char, limit_vals;
+ u32 init2vals, ts_calcs, val, filter, i;
+
+ svs_switch_bank(svs);
+
+ des_char = ((svsb->bdes << 8) & GENMASK(15, 8)) |
+ (svsb->mdes & GENMASK(7, 0));
+ svs_writel(svs, des_char, DESCHAR);
+
+ temp_char = ((svsb->vco << 16) & GENMASK(23, 16)) |
+ ((svsb->mtdes << 8) & GENMASK(15, 8)) |
+ (svsb->dvt_fixed & GENMASK(7, 0));
+ svs_writel(svs, temp_char, TEMPCHAR);
+
+ det_char = ((svsb->dcbdet << 8) & GENMASK(15, 8)) |
+ (svsb->dcmdet & GENMASK(7, 0));
+ svs_writel(svs, det_char, DETCHAR);
+
+ svs_writel(svs, svsb->dc_config, DCCONFIG);
+ svs_writel(svs, svsb->age_config, AGECONFIG);
+
+ if (!svsb->agem) {
+ svs_writel(svs, SVSB_RUNCONFIG_DEFAULT, RUNCONFIG);
+ } else {
+ val = 0x0;
+
+ for (i = 0; i < 24; i += 2) {
+ filter = 0x3 << i;
+
+ if (!(svsb->age_config & filter))
+ val |= (0x1 << i);
+ else
+ val |= (svsb->age_config & filter);
+ }
+ svs_writel(svs, val, RUNCONFIG);
+ }
+
+ svsp->set_freqs_pct(svs);
+
+ limit_vals = ((svsb->vmax << 24) & GENMASK(31, 24)) |
+ ((svsb->vmin << 16) & GENMASK(23, 16)) |
+ ((svsb->dthi << 8) & GENMASK(15, 8)) |
+ (svsb->dtlo & GENMASK(7, 0));
+ svs_writel(svs, limit_vals, LIMITVALS);
+ svs_writel(svs, (svsb->vboot & GENMASK(7, 0)), VBOOT);
+ svs_writel(svs, (svsb->det_window & GENMASK(15, 0)), DETWINDOW);
+ svs_writel(svs, (svsb->det_max & GENMASK(15, 0)), CONFIG);
+
+ if (svsb->chk_shift)
+ svs_writel(svs, (svsb->chk_shift & GENMASK(7, 0)), CHKSHIFT);
+
+ if (svsb->ctl0)
+ svs_writel(svs, svsb->ctl0, CTL0);
+
+ svs_writel(svs, SVSB_INTSTS_CLEAN, INTSTS);
+
+ switch (target_phase) {
+ case SVSB_PHASE_INIT01:
+ svs_writel(svs, SVSB_INTEN_INIT0x, INTEN);
+ svs_writel(svs, SVSB_EN_INIT01, SVSEN);
+ break;
+ case SVSB_PHASE_INIT02:
+ svs_writel(svs, SVSB_INTEN_INIT0x, INTEN);
+ init2vals = ((svsb->age_voffset_in << 16) & GENMASK(31, 16)) |
+ (svsb->dc_voffset_in & GENMASK(15, 0));
+ svs_writel(svs, init2vals, INIT2VALS);
+ svs_writel(svs, SVSB_EN_INIT02, SVSEN);
+ break;
+ case SVSB_PHASE_MON:
+ ts_calcs = ((svsb->bts << 12) & GENMASK(23, 12)) |
+ (svsb->mts & GENMASK(11, 0));
+ svs_writel(svs, ts_calcs, TSCALCS);
+ svs_writel(svs, SVSB_INTEN_MONVOPEN, INTEN);
+ svs_writel(svs, SVSB_EN_MON, SVSEN);
+ break;
+ default:
+ WARN_ON(1);
+ break;
+ }
+}
+
+static inline void svs_init01_isr_handler(struct mtk_svs *svs)
+{
+ struct svs_bank *svsb = svs->pbank;
+
+ dev_notice(svsb->dev, "%s: VDN74:0x%08x, VDN30:0x%08x, DC:0x%08x\n",
+ __func__, svs_readl(svs, VDESIGN74),
+ svs_readl(svs, VDESIGN30), svs_readl(svs, DCVALUES));
+
+ svsb->phase = SVSB_PHASE_INIT01;
+ svsb->dc_voffset_in = ~(svs_readl(svs, DCVALUES) & GENMASK(15, 0)) + 1;
+ if (svsb->init01_volt_flag == SVSB_INIT01_VOLT_IGNORE)
+ svsb->dc_voffset_in = 0;
+ else if ((svsb->dc_voffset_in & SVSB_DC_SIGNED_BIT) &&
+ (svsb->init01_volt_flag == SVSB_INIT01_VOLT_INC_ONLY))
+ svsb->dc_voffset_in = 0;
+
+ svsb->age_voffset_in = svs_readl(svs, AGEVALUES) & GENMASK(15, 0);
+
+ svs_writel(svs, SVSB_EN_OFF, SVSEN);
+ svs_writel(svs, SVSB_INTSTS_COMPLETE, INTSTS);
+
+ /* svs init01 clock gating */
+ svsb->core_sel &= ~SVSB_INIT01_CLK_EN;
+ complete(&svsb->init_completion);
+}
+
+static inline void svs_init02_isr_handler(struct mtk_svs *svs)
+{
+ const struct svs_platform *svsp = svs->platform;
+ struct svs_bank *svsb = svs->pbank;
+
+ dev_notice(svsb->dev, "%s: VOP74:0x%08x, VOP30:0x%08x, DC:0x%08x\n",
+ __func__, svs_readl(svs, VOP74), svs_readl(svs, VOP30),
+ svs_readl(svs, DCVALUES));
+
+ svsb->phase = SVSB_PHASE_INIT02;
+ svsp->get_vops(svs);
+
+ svs_writel(svs, SVSB_EN_OFF, SVSEN);
+ svs_writel(svs, SVSB_INTSTS_COMPLETE, INTSTS);
+
+ complete(&svsb->init_completion);
+}
+
+static inline void svs_mon_mode_isr_handler(struct mtk_svs *svs)
+{
+ const struct svs_platform *svsp = svs->platform;
+ struct svs_bank *svsb = svs->pbank;
+
+ svsb->phase = SVSB_PHASE_MON;
+ svsb->temp = svs_readl(svs, TEMP) & GENMASK(7, 0);
+ svsp->get_vops(svs);
+
+ svs_writel(svs, SVSB_INTSTS_MONVOP, INTSTS);
+}
+
+static inline void svs_error_isr_handler(struct mtk_svs *svs)
+{
+ const struct svs_platform *svsp = svs->platform;
+ struct svs_bank *svsb = svs->pbank;
+
+ dev_err(svsb->dev, "%s: %s, CORESEL = 0x%08x\n",
+ __func__, svsp->name, svs_readl(svs, CORESEL));
+ dev_err(svsb->dev, "SVSEN = 0x%08x, INTSTS = 0x%08x\n",
+ svs_readl(svs, SVSEN), svs_readl(svs, INTSTS));
+ dev_err(svsb->dev, "SMSTATE0 = 0x%08x, SMSTATE1 = 0x%08x\n",
+ svs_readl(svs, SMSTATE0), svs_readl(svs, SMSTATE1));
+ dev_err(svsb->dev, "TEMP = 0x%08x, TEMPMSR0 = 0x%08x\n",
+ svs_readl(svs, TEMP), svs_readl(svs, TEMPMSR0));
+ dev_err(svsb->dev, "TEMPMSR1 = 0x%08x, TEMPMSR2 = 0x%08x\n",
+ svs_readl(svs, TEMPMSR1), svs_readl(svs, TEMPMSR2));
+ dev_err(svsb->dev, "TEMPMONCTL0 = 0x%08x, TEMPMSRCTL1 = 0x%08x\n",
+ svs_readl(svs, TEMPMONCTL0), svs_readl(svs, TEMPMSRCTL1));
+
+ svsb->mode_support = SVSB_MODE_ALL_DISABLE;
+
+ if (svsb->phase != SVSB_PHASE_INIT01)
+ svsb->phase = SVSB_PHASE_ERROR;
+
+ svs_writel(svs, SVSB_EN_OFF, SVSEN);
+ svs_writel(svs, SVSB_INTSTS_CLEAN, INTSTS);
+}
+
+static irqreturn_t svs_isr(int irq, void *data)
+{
+ struct mtk_svs *svs = (struct mtk_svs *)data;
+ const struct svs_platform *svsp = svs->platform;
+ struct svs_bank *svsb = NULL;
+ unsigned long flags;
+ u32 idx, int_sts, svs_en;
+
+ flags = claim_mtk_svs_lock();
+ for (idx = 0; idx < svsp->bank_num; idx++) {
+ svsb = &svsp->banks[idx];
+ svs->pbank = svsb;
+
+ /* Find out which svs bank fires interrupt */
+ if (svsb->int_st & svs_readl(svs, INTST))
+ continue;
+
+ if (!svsb->suspended) {
+ svs_switch_bank(svs);
+ int_sts = svs_readl(svs, INTSTS);
+ svs_en = svs_readl(svs, SVSEN);
+
+ if (int_sts == SVSB_INTSTS_COMPLETE &&
+ ((svs_en & SVSB_EN_MASK) == SVSB_EN_INIT01))
+ svs_init01_isr_handler(svs);
+ else if ((int_sts == SVSB_INTSTS_COMPLETE) &&
+ ((svs_en & SVSB_EN_MASK) == SVSB_EN_INIT02))
+ svs_init02_isr_handler(svs);
+ else if (!!(int_sts & SVSB_INTSTS_MONVOP))
+ svs_mon_mode_isr_handler(svs);
+ else
+ svs_error_isr_handler(svs);
+ }
+
+ break;
+ }
+ release_mtk_svs_lock(flags);
+
+ if (svsb->phase != SVSB_PHASE_INIT01)
+ svs_adjust_pm_opp_volts(svsb, false);
+
+ return IRQ_HANDLED;
+}
+
+static void svs_mon_mode(struct mtk_svs *svs)
+{
+ const struct svs_platform *svsp = svs->platform;
+ struct svs_bank *svsb;
+ unsigned long flags;
+ u32 idx;
+
+ flags = claim_mtk_svs_lock();
+ for (idx = 0; idx < svsp->bank_num; idx++) {
+ svsb = &svsp->banks[idx];
+ svs->pbank = svsb;
+
+ if (!(svsb->mode_support & SVSB_MODE_MON))
+ continue;
+
+ svs_set_bank_phase(svs, SVSB_PHASE_MON);
+ }
+ release_mtk_svs_lock(flags);
+}
+
+static int svs_init02(struct mtk_svs *svs)
+{
+ const struct svs_platform *svsp = svs->platform;
+ struct svs_bank *svsb;
+ unsigned long flags, time_left;
+ u32 idx;
+
+ for (idx = 0; idx < svsp->bank_num; idx++) {
+ svsb = &svsp->banks[idx];
+ svs->pbank = svsb;
+
+ if (!(svsb->mode_support & SVSB_MODE_INIT02))
+ continue;
+
+ reinit_completion(&svsb->init_completion);
+ flags = claim_mtk_svs_lock();
+ svs_set_bank_phase(svs, SVSB_PHASE_INIT02);
+ release_mtk_svs_lock(flags);
+ time_left =
+ wait_for_completion_timeout(&svsb->init_completion,
+ msecs_to_jiffies(2000));
+ if (!time_left) {
+ dev_err(svsb->dev, "init02 completion timeout\n");
+ return -EBUSY;
+ }
+ }
+
+ return 0;
+}
+
+static int svs_init01(struct mtk_svs *svs)
+{
+ const struct svs_platform *svsp = svs->platform;
+ struct svs_bank *svsb;
+ struct pm_qos_request *qos_request;
+ unsigned long flags, time_left;
+ bool search_done;
+ int ret = -EPERM;
+ u32 opp_freqs, opp_vboot, buck_volt, idx, i;
+
+ qos_request = kzalloc(sizeof(*qos_request), GFP_KERNEL);
+ if (!qos_request)
+ return -ENOMEM;
+
+ /* Let CPUs leave idle-off state for initializing svs_init01. */
+ cpu_latency_qos_add_request(qos_request, 0);
+
+ /*
+ * Sometimes two svs banks use the same buck.
+ * Therefore, we set each svs bank to vboot voltage first.
+ */
+ for (idx = 0; idx < svsp->bank_num; idx++) {
+ svsb = &svsp->banks[idx];
+ search_done = false;
+
+ ret = regulator_set_mode(svsb->buck, REGULATOR_MODE_FAST);
+ if (ret)
+ dev_notice(svsb->dev, "set fast mode fail: %d\n", ret);
+
+ if (svsb->mtcmos_request) {
+ ret = regulator_enable(svsb->buck);
+ if (ret) {
+ dev_err(svsb->dev, "enable \"%s\" fail: %d\n",
+ svsb->buck_name, ret);
+ goto init01_finish;
+ }
+
+ ret = dev_pm_domain_attach(svsb->dev, false);
+ if (ret) {
+ dev_err(svsb->dev,
+ "attach pm domain fail: %d\n", ret);
+ goto init01_finish;
+ }
+
+ pm_runtime_enable(svsb->dev);
+ ret = pm_runtime_get_sync(svsb->dev);
+ if (ret < 0) {
+ dev_err(svsb->dev, "mtcmos on fail: %d\n",
+ ret);
+ goto init01_finish;
+ }
+ }
+
+ /*
+ * Find the fastest freq that can be run at vboot and
+ * fix to that freq until svs_init01 is done.
+ */
+ opp_vboot = svs_bank_volt_to_opp_volt(svsb->vboot,
+ svsb->volt_step,
+ svsb->volt_base);
+
+ for (i = 0; i < svsb->opp_count; i++) {
+ opp_freqs = svsb->opp_freqs[i];
+ if (!search_done && svsb->opp_volts[i] <= opp_vboot) {
+ ret = dev_pm_opp_adjust_voltage(svsb->dev,
+ opp_freqs,
+ opp_vboot,
+ opp_vboot,
+ opp_vboot);
+ if (ret) {
+ dev_err(svsb->dev,
+ "set voltage fail: %d\n", ret);
+ goto init01_finish;
+ }
+
+ search_done = true;
+ } else {
+ dev_pm_opp_disable(svsb->dev,
+ svsb->opp_freqs[i]);
+ }
+ }
+ }
+
+ /* svs bank init01 begins */
+ for (idx = 0; idx < svsp->bank_num; idx++) {
+ svsb = &svsp->banks[idx];
+ svs->pbank = svsb;
+
+ if (!(svsb->mode_support & SVSB_MODE_INIT01))
+ continue;
+
+ opp_vboot = svs_bank_volt_to_opp_volt(svsb->vboot,
+ svsb->volt_step,
+ svsb->volt_base);
+
+ buck_volt = regulator_get_voltage(svsb->buck);
+ if (buck_volt != opp_vboot) {
+ dev_err(svsb->dev,
+ "buck voltage: %u, expected vboot: %u\n",
+ buck_volt, opp_vboot);
+ ret = -EPERM;
+ goto init01_finish;
+ }
+
+ init_completion(&svsb->init_completion);
+ flags = claim_mtk_svs_lock();
+ svs_set_bank_phase(svs, SVSB_PHASE_INIT01);
+ release_mtk_svs_lock(flags);
+ time_left =
+ wait_for_completion_timeout(&svsb->init_completion,
+ msecs_to_jiffies(2000));
+ if (!time_left) {
+ dev_err(svsb->dev, "init01 completion timeout\n");
+ ret = -EBUSY;
+ goto init01_finish;
+ }
+ }
+
+init01_finish:
+ for (idx = 0; idx < svsp->bank_num; idx++) {
+ svsb = &svsp->banks[idx];
+
+ for (i = 0; i < svsb->opp_count; i++)
+ dev_pm_opp_enable(svsb->dev, svsb->opp_freqs[i]);
+
+ if (regulator_set_mode(svsb->buck, REGULATOR_MODE_NORMAL))
+ dev_notice(svsb->dev, "fail to set normal mode: %d\n",
+ ret);
+
+ if (svsb->mtcmos_request) {
+ if (pm_runtime_put_sync(svsb->dev))
+ dev_err(svsb->dev, "mtcmos off fail: %d\n",
+ ret);
+ pm_runtime_disable(svsb->dev);
+ dev_pm_domain_detach(svsb->dev, 0);
+ if (regulator_disable(svsb->buck))
+ dev_err(svsb->dev,
+ "disable \"%s\" power fail: %d\n",
+ svsb->buck_name, ret);
+ }
+ }
+
+ cpu_latency_qos_remove_request(qos_request);
+ kfree(qos_request);
+
+ return ret;
+}
+
+static int svs_start(struct mtk_svs *svs)
+{
+ int ret;
+
+ ret = svs_init01(svs);
+ if (ret)
+ return ret;
+
+ ret = svs_init02(svs);
+ if (ret)
+ return ret;
+
+ svs_mon_mode(svs);
+
+ return ret;
+}
+
+static bool svs_mt8183_efuse_parsing(struct mtk_svs *svs)
+{
+ const struct svs_platform *svsp = svs->platform;
+ struct thermal_parameter tp;
+ struct svs_bank *svsb;
+ bool mon_mode_support = true;
+ int format[6], x_roomt[6], tb_roomt = 0;
+ struct nvmem_cell *cell;
+ u32 idx, i, ft_pgm, mts, temp0, temp1, temp2;
+
+ if (svsp->fake_efuse) {
+ pr_notice("fake efuse\n");
+ svs->efuse[0] = 0x00310080;
+ svs->efuse[1] = 0xabfbf757;
+ svs->efuse[2] = 0x47c747c7;
+ svs->efuse[3] = 0xabfbf757;
+ svs->efuse[4] = 0xe7fca0ec;
+ svs->efuse[5] = 0x47bf4b88;
+ svs->efuse[6] = 0xabfb8fa5;
+ svs->efuse[7] = 0xabfb217b;
+ svs->efuse[8] = 0x4bf34be1;
+ svs->efuse[9] = 0xabfb670d;
+ svs->efuse[16] = 0xabfbc653;
+ svs->efuse[17] = 0x47f347e1;
+ svs->efuse[18] = 0xabfbd848;
+ }
+
+ for (i = 0; i < svs->efuse_num; i++)
+ if (svs->efuse[i])
+ dev_notice(svs->dev, "M_HW_RES%d: 0x%08x\n",
+ i, svs->efuse[i]);
+
+ /* svs efuse parsing */
+ ft_pgm = (svs->efuse[0] >> 4) & GENMASK(3, 0);
+
+ for (idx = 0; idx < svsp->bank_num; idx++) {
+ svsb = &svsp->banks[idx];
+ if (ft_pgm <= 1)
+ svsb->init01_volt_flag = SVSB_INIT01_VOLT_IGNORE;
+
+ switch (svsb->sw_id) {
+ case SVSB_CPU_LITTLE:
+ svsb->bdes = svs->efuse[16] & GENMASK(7, 0);
+ svsb->mdes = (svs->efuse[16] >> 8) & GENMASK(7, 0);
+ svsb->dcbdet = (svs->efuse[16] >> 16) & GENMASK(7, 0);
+ svsb->dcmdet = (svs->efuse[16] >> 24) & GENMASK(7, 0);
+ svsb->mtdes = (svs->efuse[17] >> 16) & GENMASK(7, 0);
+
+ if (ft_pgm <= 3)
+ svsb->volt_offset += 10;
+ else
+ svsb->volt_offset += 2;
+ break;
+ case SVSB_CPU_BIG:
+ svsb->bdes = svs->efuse[18] & GENMASK(7, 0);
+ svsb->mdes = (svs->efuse[18] >> 8) & GENMASK(7, 0);
+ svsb->dcbdet = (svs->efuse[18] >> 16) & GENMASK(7, 0);
+ svsb->dcmdet = (svs->efuse[18] >> 24) & GENMASK(7, 0);
+ svsb->mtdes = svs->efuse[17] & GENMASK(7, 0);
+
+ if (ft_pgm <= 3)
+ svsb->volt_offset += 15;
+ else
+ svsb->volt_offset += 12;
+ break;
+ case SVSB_CCI:
+ svsb->bdes = svs->efuse[4] & GENMASK(7, 0);
+ svsb->mdes = (svs->efuse[4] >> 8) & GENMASK(7, 0);
+ svsb->dcbdet = (svs->efuse[4] >> 16) & GENMASK(7, 0);
+ svsb->dcmdet = (svs->efuse[4] >> 24) & GENMASK(7, 0);
+ svsb->mtdes = (svs->efuse[5] >> 16) & GENMASK(7, 0);
+
+ if (ft_pgm <= 3)
+ svsb->volt_offset += 10;
+ else
+ svsb->volt_offset += 2;
+ break;
+ case SVSB_GPU:
+ svsb->bdes = svs->efuse[6] & GENMASK(7, 0);
+ svsb->mdes = (svs->efuse[6] >> 8) & GENMASK(7, 0);
+ svsb->dcbdet = (svs->efuse[6] >> 16) & GENMASK(7, 0);
+ svsb->dcmdet = (svs->efuse[6] >> 24) & GENMASK(7, 0);
+ svsb->mtdes = svs->efuse[5] & GENMASK(7, 0);
+
+ if (ft_pgm >= 2) {
+ svsb->freq_base = 800000000; /* 800MHz */
+ svsb->dvt_fixed = 2;
+ }
+ break;
+ default:
+ break;
+ }
+ }
+
+ /* Get thermal efuse by nvmem */
+ cell = nvmem_cell_get(svs->dev, "calibration-data");
+ if (IS_ERR(cell)) {
+ dev_err(svs->dev, "no thermal cell, no mon mode\n");
+ for (idx = 0; idx < svsp->bank_num; idx++) {
+ svsb = &svsp->banks[idx];
+ svsb->mode_support &= ~SVSB_MODE_MON;
+ }
+ return true;
+ }
+
+ svs->thermal_efuse = (u32 *)nvmem_cell_read(cell,
+ &svs->thermal_efuse_num);
+ svs->thermal_efuse_num /= sizeof(u32);
+ nvmem_cell_put(cell);
+
+ if (svsp->fake_efuse) {
+ svs->thermal_efuse[0] = 0x02873f69;
+ svs->thermal_efuse[1] = 0xa11d9142;
+ svs->thermal_efuse[2] = 0xa2526900;
+ }
+
+ /* Thermal efuse parsing */
+ tp.adc_ge_t = (svs->thermal_efuse[1] >> 22) & GENMASK(9, 0);
+ tp.adc_oe_t = (svs->thermal_efuse[1] >> 12) & GENMASK(9, 0);
+
+ tp.o_vtsmcu1 = (svs->thermal_efuse[0] >> 17) & GENMASK(8, 0);
+ tp.o_vtsmcu2 = (svs->thermal_efuse[0] >> 8) & GENMASK(8, 0);
+ tp.o_vtsmcu3 = svs->thermal_efuse[1] & GENMASK(8, 0);
+ tp.o_vtsmcu4 = (svs->thermal_efuse[2] >> 23) & GENMASK(8, 0);
+ tp.o_vtsmcu5 = (svs->thermal_efuse[2] >> 5) & GENMASK(8, 0);
+ tp.o_vtsabb = (svs->thermal_efuse[2] >> 14) & GENMASK(8, 0);
+
+ tp.degc_cali = (svs->thermal_efuse[0] >> 1) & GENMASK(5, 0);
+ tp.adc_cali_en_t = svs->thermal_efuse[0] & BIT(0);
+ tp.o_slope_sign = (svs->thermal_efuse[0] >> 7) & BIT(0);
+
+ tp.ts_id = (svs->thermal_efuse[1] >> 9) & BIT(0);
+ tp.o_slope = (svs->thermal_efuse[0] >> 26) & GENMASK(5, 0);
+
+ if (tp.adc_cali_en_t == 1) {
+ if (!tp.ts_id)
+ tp.o_slope = 0;
+
+ if ((tp.adc_ge_t < 265 || tp.adc_ge_t > 758) ||
+ (tp.adc_oe_t < 265 || tp.adc_oe_t > 758) ||
+ (tp.o_vtsmcu1 < -8 || tp.o_vtsmcu1 > 484) ||
+ (tp.o_vtsmcu2 < -8 || tp.o_vtsmcu2 > 484) ||
+ (tp.o_vtsmcu3 < -8 || tp.o_vtsmcu3 > 484) ||
+ (tp.o_vtsmcu4 < -8 || tp.o_vtsmcu4 > 484) ||
+ (tp.o_vtsmcu5 < -8 || tp.o_vtsmcu5 > 484) ||
+ (tp.o_vtsabb < -8 || tp.o_vtsabb > 484) ||
+ (tp.degc_cali < 1 || tp.degc_cali > 63)) {
+ dev_err(svs->dev, "bad thermal efuse, no mon mode\n");
+ mon_mode_support = false;
+ }
+ } else {
+ dev_err(svs->dev, "no thermal efuse, no mon mode\n");
+ mon_mode_support = false;
+ }
+
+ if (!mon_mode_support) {
+ for (idx = 0; idx < svsp->bank_num; idx++) {
+ svsb = &svsp->banks[idx];
+ svsb->mode_support &= ~SVSB_MODE_MON;
+ }
+
+ return true;
+ }
+
+ tp.ge = ((tp.adc_ge_t - 512) * 10000) / 4096;
+ tp.oe = (tp.adc_oe_t - 512);
+ tp.gain = (10000 + tp.ge);
+
+ format[0] = (tp.o_vtsmcu1 + 3350 - tp.oe);
+ format[1] = (tp.o_vtsmcu2 + 3350 - tp.oe);
+ format[2] = (tp.o_vtsmcu3 + 3350 - tp.oe);
+ format[3] = (tp.o_vtsmcu4 + 3350 - tp.oe);
+ format[4] = (tp.o_vtsmcu5 + 3350 - tp.oe);
+ format[5] = (tp.o_vtsabb + 3350 - tp.oe);
+
+ for (i = 0; i < 6; i++)
+ x_roomt[i] = (((format[i] * 10000) / 4096) * 10000) / tp.gain;
+
+ temp0 = (10000 * 100000 / tp.gain) * 15 / 18;
+
+ if (!tp.o_slope_sign)
+ mts = (temp0 * 10) / (1534 + tp.o_slope * 10);
+ else
+ mts = (temp0 * 10) / (1534 - tp.o_slope * 10);
+
+ for (idx = 0; idx < svsp->bank_num; idx++) {
+ svsb = &svsp->banks[idx];
+ svsb->mts = mts;
+
+ switch (svsb->sw_id) {
+ case SVSB_CPU_LITTLE:
+ tb_roomt = x_roomt[3];
+ break;
+ case SVSB_CPU_BIG:
+ tb_roomt = x_roomt[4];
+ break;
+ case SVSB_CCI:
+ tb_roomt = x_roomt[3];
+ break;
+ case SVSB_GPU:
+ tb_roomt = x_roomt[1];
+ break;
+ default:
+ break;
+ }
+
+ temp0 = (tp.degc_cali * 10 / 2);
+ temp1 = ((10000 * 100000 / 4096 / tp.gain) *
+ tp.oe + tb_roomt * 10) * 15 / 18;
+
+ if (!tp.o_slope_sign)
+ temp2 = temp1 * 100 / (1534 + tp.o_slope * 10);
+ else
+ temp2 = temp1 * 100 / (1534 - tp.o_slope * 10);
+
+ svsb->bts = (temp0 + temp2 - 250) * 4 / 10;
+ }
+
+ return true;
+}
+
+static bool svs_is_supported(struct mtk_svs *svs)
+{
+ const struct svs_platform *svsp = svs->platform;
+ struct nvmem_cell *cell;
+
+ /* Get svs efuse by nvmem */
+ cell = nvmem_cell_get(svs->dev, "svs-calibration-data");
+ if (IS_ERR(cell)) {
+ dev_err(svs->dev,
+ "no \"svs-calibration-data\" from dts? disable svs\n");
+ return false;
+ }
+
+ svs->efuse = (u32 *)nvmem_cell_read(cell, &svs->efuse_num);
+ svs->efuse_num /= sizeof(u32);
+ nvmem_cell_put(cell);
+
+ if (!svsp->fake_efuse && !svs->efuse[svsp->efuse_check]) {
+ dev_err(svs->dev, "svs_efuse[%u] = 0x%x?\n",
+ svsp->efuse_check, svs->efuse[svsp->efuse_check]);
+ return false;
+ }
+
+ return svsp->efuse_parsing(svs);
+}
+
+static int svs_resource_setup(struct mtk_svs *svs)
+{
+ const struct svs_platform *svsp = svs->platform;
+ struct svs_bank *svsb;
+ struct platform_device *pdev;
+ struct device_node *np = NULL;
+ struct dev_pm_opp *opp;
+ unsigned long freq;
+ int count, ret;
+ u32 idx, i;
+
+ dev_set_drvdata(svs->dev, svs);
+
+ for (idx = 0; idx < svsp->bank_num; idx++) {
+ svsb = &svsp->banks[idx];
+
+ switch (svsb->sw_id) {
+ case SVSB_CPU_LITTLE:
+ svsb->name = "SVSB_CPU_LITTLE";
+ break;
+ case SVSB_CPU_BIG:
+ svsb->name = "SVSB_CPU_BIG";
+ break;
+ case SVSB_CCI:
+ svsb->name = "SVSB_CCI";
+ break;
+ case SVSB_GPU:
+ svsb->name = "SVSB_GPU";
+ break;
+ default:
+ WARN_ON(1);
+ return -EINVAL;
+ }
+
+ /* Add svs bank device for opp-table/mtcmos/buck control */
+ pdev = platform_device_alloc(svsb->name, 0);
+ if (!pdev) {
+ dev_err(svs->dev, "%s: alloc pdev fail\n", svsb->name);
+ return -ENOMEM;
+ }
+
+ for_each_child_of_node(svs->dev->of_node, np) {
+ if (of_device_is_compatible(np, svsb->of_compatible)) {
+ pdev->dev.of_node = np;
+ break;
+ }
+ }
+
+ ret = platform_device_add(pdev);
+ if (ret) {
+ dev_err(svs->dev, "%s: add device fail: %d\n",
+ svsb->name, ret);
+ return ret;
+ }
+
+ svsb->dev = &pdev->dev;
+ dev_set_drvdata(svsb->dev, svs);
+ ret = dev_pm_opp_of_add_table(svsb->dev);
+ if (ret) {
+ dev_err(svsb->dev, "add opp table fail: %d\n", ret);
+ return ret;
+ }
+
+ mutex_init(&svsb->lock);
+
+ svsb->buck = devm_regulator_get_optional(svsb->dev,
+ svsb->buck_name);
+ if (IS_ERR(svsb->buck)) {
+ dev_err(svsb->dev, "cannot get \"%s-supply\"\n",
+ svsb->buck_name);
+ return PTR_ERR(svsb->buck);
+ }
+
+ count = dev_pm_opp_get_opp_count(svsb->dev);
+ if (svsb->opp_count != count) {
+ dev_err(svsb->dev,
+ "opp_count not \"%u\" but get \"%d\"?\n",
+ svsb->opp_count, count);
+ return count;
+ }
+
+ for (i = 0, freq = U32_MAX; i < svsb->opp_count; i++, freq--) {
+ opp = dev_pm_opp_find_freq_floor(svsb->dev, &freq);
+ if (IS_ERR(opp)) {
+ dev_err(svsb->dev, "cannot find freq = %ld\n",
+ PTR_ERR(opp));
+ return PTR_ERR(opp);
+ }
+
+ svsb->opp_freqs[i] = freq;
+ svsb->opp_volts[i] = dev_pm_opp_get_voltage(opp);
+ svsb->freqs_pct[i] = percent(svsb->opp_freqs[i],
+ svsb->freq_base);
+ dev_pm_opp_put(opp);
+ }
+ }
+
+ return 0;
+}
+
+static int svs_suspend(struct device *dev)
+{
+ struct mtk_svs *svs = dev_get_drvdata(dev);
+ const struct svs_platform *svsp = svs->platform;
+ struct svs_bank *svsb;
+ unsigned long flags;
+ int ret;
+ u32 idx;
+
+ /* Wait if svs_isr() is still in proecess. Suspend all banks. */
+ flags = claim_mtk_svs_lock();
+ for (idx = 0; idx < svsp->bank_num; idx++) {
+ svsb = &svsp->banks[idx];
+ svs->pbank = svsb;
+ svs_switch_bank(svs);
+ svs_writel(svs, SVSB_EN_OFF, SVSEN);
+ svs_writel(svs, SVSB_INTSTS_CLEAN, INTSTS);
+ svsb->suspended = true;
+ }
+ release_mtk_svs_lock(flags);
+
+ for (idx = 0; idx < svsp->bank_num; idx++) {
+ svsb = &svsp->banks[idx];
+ if (svsb->phase != SVSB_PHASE_INIT01) {
+ svsb->phase = SVSB_PHASE_ERROR;
+ svs_adjust_pm_opp_volts(svsb, true);
+ }
+ }
+
+ if (svsp->need_hw_reset) {
+ ret = device_reset(svs->dev);
+ if (ret) {
+ dev_err(svs->dev, "device reset fail = %d\n", ret);
+ return ret;
+ }
+ }
+
+ clk_disable_unprepare(svs->main_clk);
+
+ return 0;
+}
+
+static int svs_resume(struct device *dev)
+{
+ struct mtk_svs *svs = dev_get_drvdata(dev);
+ const struct svs_platform *svsp = svs->platform;
+ struct svs_bank *svsb;
+ int ret;
+ u32 idx;
+
+ ret = clk_prepare_enable(svs->main_clk);
+ if (ret) {
+ dev_err(svs->dev, "cannot enable main_clk, disable svs\n");
+ return ret;
+ }
+
+ for (idx = 0; idx < svsp->bank_num; idx++) {
+ svsb = &svsp->banks[idx];
+ svsb->suspended = false;
+ }
+
+ ret = svs_init02(svs);
+ if (ret)
+ return ret;
+
+ svs_mon_mode(svs);
+
+ return 0;
+}
+
+static struct svs_bank svs_mt8183_banks[4] = {
+ {
+ .of_compatible = "mediatek,mt8183-svs-cpu-little",
+ .sw_id = SVSB_CPU_LITTLE,
+ .tzone_name = "tzts4",
+ .buck_name = "vcpu-little",
+ .mtcmos_request = false,
+ .init01_volt_flag = SVSB_INIT01_VOLT_INC_ONLY,
+ .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02,
+ .opp_count = 16,
+ .freq_base = 1989000000,
+ .vboot = 0x30,
+ .volt_step = 6250,
+ .volt_base = 500000,
+ .volt_offset = 0,
+ .vmax = 0x64,
+ .vmin = 0x18,
+ .dthi = 0x1,
+ .dtlo = 0xfe,
+ .det_window = 0xa28,
+ .det_max = 0xffff,
+ .age_config = 0x555555,
+ .agem = 0,
+ .dc_config = 0x555555,
+ .dvt_fixed = 0x7,
+ .vco = 0x10,
+ .chk_shift = 0x77,
+ .temp_upper_bound = 0x64,
+ .temp_lower_bound = 0xb2,
+ .tzone_high_temp = SVSB_TZONE_HIGH_TEMP_MAX,
+ .tzone_low_temp = 25000,
+ .tzone_low_temp_offset = 0,
+ .core_sel = 0x8fff0000,
+ .int_st = BIT(0),
+ .ctl0 = 0x00010001,
+ },
+ {
+ .of_compatible = "mediatek,mt8183-svs-cpu-big",
+ .sw_id = SVSB_CPU_BIG,
+ .tzone_name = "tzts5",
+ .buck_name = "vcpu-big",
+ .mtcmos_request = false,
+ .init01_volt_flag = SVSB_INIT01_VOLT_INC_ONLY,
+ .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02,
+ .opp_count = 16,
+ .freq_base = 1989000000,
+ .vboot = 0x30,
+ .volt_step = 6250,
+ .volt_base = 500000,
+ .volt_offset = 0,
+ .vmax = 0x58,
+ .vmin = 0x10,
+ .dthi = 0x1,
+ .dtlo = 0xfe,
+ .det_window = 0xa28,
+ .det_max = 0xffff,
+ .age_config = 0x555555,
+ .agem = 0,
+ .dc_config = 0x555555,
+ .dvt_fixed = 0x7,
+ .vco = 0x10,
+ .chk_shift = 0x77,
+ .temp_upper_bound = 0x64,
+ .temp_lower_bound = 0xb2,
+ .tzone_high_temp = SVSB_TZONE_HIGH_TEMP_MAX,
+ .tzone_low_temp = 25000,
+ .tzone_low_temp_offset = 0,
+ .core_sel = 0x8fff0001,
+ .int_st = BIT(1),
+ .ctl0 = 0x00000001,
+ },
+ {
+ .of_compatible = "mediatek,mt8183-svs-cci",
+ .sw_id = SVSB_CCI,
+ .tzone_name = "tzts4",
+ .buck_name = "vcci",
+ .mtcmos_request = false,
+ .init01_volt_flag = SVSB_INIT01_VOLT_INC_ONLY,
+ .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02,
+ .opp_count = 16,
+ .freq_base = 1196000000,
+ .vboot = 0x30,
+ .volt_step = 6250,
+ .volt_base = 500000,
+ .volt_offset = 0,
+ .vmax = 0x64,
+ .vmin = 0x18,
+ .dthi = 0x1,
+ .dtlo = 0xfe,
+ .det_window = 0xa28,
+ .det_max = 0xffff,
+ .age_config = 0x555555,
+ .agem = 0,
+ .dc_config = 0x555555,
+ .dvt_fixed = 0x7,
+ .vco = 0x10,
+ .chk_shift = 0x77,
+ .temp_upper_bound = 0x64,
+ .temp_lower_bound = 0xb2,
+ .tzone_high_temp = SVSB_TZONE_HIGH_TEMP_MAX,
+ .tzone_low_temp = 25000,
+ .tzone_low_temp_offset = 0,
+ .core_sel = 0x8fff0002,
+ .int_st = BIT(2),
+ .ctl0 = 0x00100003,
+ },
+ {
+ .of_compatible = "mediatek,mt8183-svs-gpu",
+ .sw_id = SVSB_GPU,
+ .tzone_name = "tzts2",
+ .buck_name = "vgpu",
+ .mtcmos_request = true,
+ .init01_volt_flag = SVSB_INIT01_VOLT_INC_ONLY,
+ .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02 |
+ SVSB_MODE_MON,
+ .opp_count = 16,
+ .freq_base = 900000000,
+ .vboot = 0x30,
+ .volt_step = 6250,
+ .volt_base = 500000,
+ .volt_offset = 0,
+ .vmax = 0x40,
+ .vmin = 0x14,
+ .dthi = 0x1,
+ .dtlo = 0xfe,
+ .det_window = 0xa28,
+ .det_max = 0xffff,
+ .age_config = 0x555555,
+ .agem = 0,
+ .dc_config = 0x555555,
+ .dvt_fixed = 0x3,
+ .vco = 0x10,
+ .chk_shift = 0x77,
+ .temp_upper_bound = 0x64,
+ .temp_lower_bound = 0xb2,
+ .tzone_high_temp = SVSB_TZONE_HIGH_TEMP_MAX,
+ .tzone_low_temp = 25000,
+ .tzone_low_temp_offset = 3,
+ .core_sel = 0x8fff0003,
+ .int_st = BIT(3),
+ .ctl0 = 0x00050001,
+ },
+};
+
+static const struct svs_platform svs_mt8183_platform = {
+ .name = "mt8183-svs",
+ .suppliers = {"thermal", "mali"},
+ .banks = svs_mt8183_banks,
+ .efuse_parsing = svs_mt8183_efuse_parsing,
+ .set_freqs_pct = svs_set_freqs_pct_v2,
+ .get_vops = svs_get_vops_v2,
+ .regs = svs_regs_v2,
+ .irqflags = IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+ .need_hw_reset = false,
+ .fake_efuse = false,
+ .bank_num = 4,
+ .efuse_check = 2,
+};
+
+static const struct of_device_id mtk_svs_of_match[] = {
+ {
+ .compatible = "mediatek,mt8183-svs",
+ .data = &svs_mt8183_platform,
+ }, {
+ /* Sentinel */
+ },
+};
+
+static int svs_add_supplier_device_link(struct mtk_svs *svs)
+{
+ const struct svs_platform *svsp = svs->platform;
+ struct device_node *sup_node;
+ struct platform_device *sup_pdev;
+ struct device_link *sup_link;
+ u32 i;
+
+ for (i = 0; i < ARRAY_SIZE(svsp->suppliers); i++) {
+ if (!svsp->suppliers[i])
+ continue;
+
+ sup_node = of_find_node_by_name(NULL, svsp->suppliers[i]);
+ if (!sup_node) {
+ dev_notice(svs->dev, "no %s node? pass dev-link\n",
+ svsp->suppliers[i]);
+ continue;
+ }
+
+ sup_pdev = of_find_device_by_node(sup_node);
+ if (!sup_pdev) {
+ dev_notice(svs->dev, "no %pOF pdev? pass dev-link\n",
+ sup_node);
+ of_node_put(sup_node);
+ continue;
+ }
+
+ of_node_put(sup_node);
+
+ sup_link = device_link_add(svs->dev, &sup_pdev->dev,
+ DL_FLAG_AUTOREMOVE_CONSUMER);
+
+ if (sup_link->status == DL_STATE_DORMANT)
+ return -EPROBE_DEFER;
+ }
+
+ return 0;
+}
+
+static int svs_probe(struct platform_device *pdev)
+{
+ struct mtk_svs *svs;
+ unsigned int svs_irq;
+ int ret;
+
+ svs = devm_kzalloc(&pdev->dev, sizeof(*svs), GFP_KERNEL);
+ if (!svs)
+ return -ENOMEM;
+
+ svs->dev = &pdev->dev;
+ svs->platform = of_device_get_match_data(svs->dev);
+ if (!svs->platform) {
+ dev_err(svs->dev, "svs platform data isn't set yet\n");
+ return -EPERM;
+ }
+
+ ret = svs_add_supplier_device_link(svs);
+ if (ret)
+ return ret;
+
+ svs->base = of_iomap(svs->dev->of_node, 0);
+ if (IS_ERR(svs->base)) {
+ dev_err(svs->dev, "cannot find svs register base\n");
+ return PTR_ERR(svs->base);
+ }
+
+ svs_irq = irq_of_parse_and_map(svs->dev->of_node, 0);
+ ret = devm_request_threaded_irq(svs->dev, svs_irq, NULL, svs_isr,
+ svs->platform->irqflags, "mtk-svs",
+ svs);
+ if (ret) {
+ dev_err(svs->dev, "register irq(%d) failed: %d\n",
+ svs_irq, ret);
+ return ret;
+ }
+
+ svs->main_clk = devm_clk_get(svs->dev, "main");
+ if (IS_ERR(svs->main_clk)) {
+ dev_err(svs->dev, "failed to get clock: %ld\n",
+ PTR_ERR(svs->main_clk));
+ return PTR_ERR(svs->main_clk);
+ }
+
+ ret = clk_prepare_enable(svs->main_clk);
+ if (ret) {
+ dev_err(svs->dev, "cannot enable main clk: %d\n", ret);
+ return ret;
+ }
+
+ if (!svs_is_supported(svs)) {
+ dev_notice(svs->dev, "svs is not supported\n");
+ ret = -EPERM;
+ goto svs_probe_clk_disable;
+ }
+
+ ret = svs_resource_setup(svs);
+ if (ret)
+ goto svs_probe_clk_disable;
+
+ ret = svs_start(svs);
+ if (ret)
+ goto svs_probe_clk_disable;
+
+ return 0;
+
+svs_probe_clk_disable:
+ clk_disable_unprepare(svs->main_clk);
+
+ return ret;
+}
+
+static SIMPLE_DEV_PM_OPS(svs_pm_ops, svs_suspend, svs_resume);
+
+static struct platform_driver svs_driver = {
+ .probe = svs_probe,
+ .driver = {
+ .name = "mtk-svs",
+ .pm = &svs_pm_ops,
+ .of_match_table = of_match_ptr(mtk_svs_of_match),
+ },
+};
+
+module_platform_driver(svs_driver);
+
+MODULE_AUTHOR("Roger Lu <roger...@mediatek.com>");
+MODULE_DESCRIPTION("MediaTek SVS driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/power/mtk_svs.h b/include/linux/power/mtk_svs.h
new file mode 100644
index 000000000000..5c03982e3576
--- /dev/null
+++ b/include/linux/power/mtk_svs.h
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * Copyright (C) 2020 MediaTek Inc.
+ */
+
+#ifndef __MTK_SVS_H__
+#define __MTK_SVS_H__
+
+#if IS_ENABLED(CONFIG_MTK_SVS)
+unsigned long claim_mtk_svs_lock(void);
+void release_mtk_svs_lock(unsigned long flags);
+#else
+static inline unsigned long claim_mtk_svs_lock(void)
+{
+ return 0;
+}
+
+static inline void release_mtk_svs_lock(unsigned long flags)
+{
+}
+#endif /* CONFIG_MTK_SVS */
+
+#endif /* __MTK_SVS_H__ */
--
2.18.0
