On Sat 12 Sep 16:08 CDT 2020, Douglas Anderson wrote:
> We always toggle the chip select manually in spi-geni-qcom so that we
> can properly implement the Linux API. There's no reason to program
> this to the hardware on every transfer. Program it once at init and
> be done with it.
>
> This saves some part of a microsecond of overhead on each transfer.
> While not really noticeable on any real world benchmarks, we might as
> well save the time.
>
Reviewed-by: Bjorn Andersson <bjorn.anders...@linaro.org>
Regards,
Bjorn
> Signed-off-by: Douglas Anderson <diand...@chromium.org>
> ---
>
> drivers/spi/spi-geni-qcom.c | 12 +++++++-----
> 1 file changed, 7 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/spi/spi-geni-qcom.c b/drivers/spi/spi-geni-qcom.c
> index 7f0bf0dec466..92d88bf85a90 100644
> --- a/drivers/spi/spi-geni-qcom.c
> +++ b/drivers/spi/spi-geni-qcom.c
> @@ -290,6 +290,7 @@ static int spi_geni_init(struct spi_geni_master *mas)
> {
> struct geni_se *se = &mas->se;
> unsigned int proto, major, minor, ver;
> + u32 spi_tx_cfg;
>
> pm_runtime_get_sync(mas->dev);
>
> @@ -322,6 +323,11 @@ static int spi_geni_init(struct spi_geni_master *mas)
>
> geni_se_select_mode(se, GENI_SE_FIFO);
>
> + /* We always control CS manually */
> + spi_tx_cfg = readl(se->base + SE_SPI_TRANS_CFG);
> + spi_tx_cfg &= ~CS_TOGGLE;
> + writel(spi_tx_cfg, se->base + SE_SPI_TRANS_CFG);
> +
> pm_runtime_put(mas->dev);
> return 0;
> }
> @@ -331,7 +337,7 @@ static void setup_fifo_xfer(struct spi_transfer *xfer,
> u16 mode, struct spi_master *spi)
> {
> u32 m_cmd = 0;
> - u32 spi_tx_cfg, len;
> + u32 len;
> struct geni_se *se = &mas->se;
> int ret;
>
> @@ -350,7 +356,6 @@ static void setup_fifo_xfer(struct spi_transfer *xfer,
> spin_lock_irq(&mas->lock);
> spin_unlock_irq(&mas->lock);
>
> - spi_tx_cfg = readl(se->base + SE_SPI_TRANS_CFG);
> if (xfer->bits_per_word != mas->cur_bits_per_word) {
> spi_setup_word_len(mas, mode, xfer->bits_per_word);
> mas->cur_bits_per_word = xfer->bits_per_word;
> @@ -364,8 +369,6 @@ static void setup_fifo_xfer(struct spi_transfer *xfer,
> mas->tx_rem_bytes = 0;
> mas->rx_rem_bytes = 0;
>
> - spi_tx_cfg &= ~CS_TOGGLE;
> -
> if (!(mas->cur_bits_per_word % MIN_WORD_LEN))
> len = xfer->len * BITS_PER_BYTE / mas->cur_bits_per_word;
> else
> @@ -384,7 +387,6 @@ static void setup_fifo_xfer(struct spi_transfer *xfer,
> writel(len, se->base + SE_SPI_RX_TRANS_LEN);
> mas->rx_rem_bytes = xfer->len;
> }
> - writel(spi_tx_cfg, se->base + SE_SPI_TRANS_CFG);
>
> /*
> * Lock around right before we start the transfer since our
> --
> 2.28.0.618.gf4bc123cb7-goog
>
