Hi Alain On 8/30/20 9:57 PM, Alain Volmat wrote: > Add the entry for the STiH418 SBC UART0 low level uart. > > Signed-off-by: Alain Volmat <[email protected]> > --- > arch/arm/Kconfig.debug | 19 +++++++++++++++++-- > 1 file changed, 17 insertions(+), 2 deletions(-) > > diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug > index e97d6e5c8898..447d177fcf8d 100644 > --- a/arch/arm/Kconfig.debug > +++ b/arch/arm/Kconfig.debug > @@ -1204,6 +1204,16 @@ choice > > If unsure, say N. > > + config DEBUG_STIH418_SBC_ASC0 > + bool "Use StiH418 SBC ASC0 UART for low-level debug" > + depends on ARCH_STI > + help > + Say Y here if you want kernel low-level debugging support > + on STiH418 based platforms which has default UART wired > + up to SBC ASC0. > + > + If unsure, say N. > + > config STM32F4_DEBUG_UART > bool "Use STM32F4 UART for low-level debug" > depends on MACH_STM32F429 || MACH_STM32F469 > @@ -1587,6 +1597,7 @@ config DEBUG_LL_INCLUDE > default "debug/sirf.S" if DEBUG_SIRFSOC_UART > default "debug/sti.S" if DEBUG_STIH41X_ASC2 > default "debug/sti.S" if DEBUG_STIH41X_SBC_ASC1 > + default "debug/sti.S" if DEBUG_STIH418_SBC_ASC0 > default "debug/stm32.S" if DEBUG_STM32_UART > default "debug/tegra.S" if DEBUG_TEGRA_UART > default "debug/ux500.S" if DEBUG_UX500_UART > @@ -1620,6 +1631,7 @@ config DEBUG_UART_PHYS > default 0x03010fe0 if ARCH_RPC > default 0x07000000 if DEBUG_SUN9I_UART0 > default 0x09405000 if DEBUG_ZTE_ZX > + default 0x09530000 if DEBUG_STIH418_SBC_ASC0 > default 0x10009000 if DEBUG_REALVIEW_STD_PORT || \ > DEBUG_VEXPRESS_UART0_CA9 > default 0x1010c000 if DEBUG_REALVIEW_PB1176_PORT > @@ -1750,7 +1762,8 @@ config DEBUG_UART_PHYS > DEBUG_BCM63XX_UART || DEBUG_ASM9260_UART || \ > DEBUG_SIRFSOC_UART || DEBUG_DIGICOLOR_UA0 || \ > DEBUG_AT91_UART || DEBUG_STM32_UART || \ > - DEBUG_STIH41X_ASC2 || DEBUG_STIH41X_SBC_ASC1 > + DEBUG_STIH41X_ASC2 || DEBUG_STIH41X_SBC_ASC1 || \ > + DEBUG_STIH418_SBC_ASC0 > > config DEBUG_UART_VIRT > hex "Virtual base address of debug UART" > @@ -1796,6 +1809,7 @@ config DEBUG_UART_VIRT > default 0xf8090000 if DEBUG_VEXPRESS_UART0_RS1 > default 0xf8ffee00 if DEBUG_AT91_SAM9263_DBGU > default 0xf8fff200 if DEBUG_AT91_RM9200_DBGU > + default 0xf9530000 if DEBUG_STIH418_SBC_ASC0 > default 0xf9e09000 if DEBUG_AM33XXUART1 > default 0xfa020000 if DEBUG_OMAP4UART3 || DEBUG_TI81XXUART1 > default 0xfa022000 if DEBUG_TI81XXUART2 > @@ -1864,7 +1878,8 @@ config DEBUG_UART_VIRT > DEBUG_BCM63XX_UART || DEBUG_ASM9260_UART || \ > DEBUG_SIRFSOC_UART || DEBUG_DIGICOLOR_UA0 || \ > DEBUG_AT91_UART || DEBUG_STM32_UART || \ > - DEBUG_STIH41X_ASC2 || DEBUG_STIH41X_SBC_ASC1 > + DEBUG_STIH41X_ASC2 || DEBUG_STIH41X_SBC_ASC1 || \ > + DEBUG_STIH418_SBC_ASC0 > > config DEBUG_UART_8250_SHIFT > int "Register offset shift for the 8250 debug UART"
Reviewed-by: Patrice Chotard <[email protected]> Thanks Patrice
