From: Paul Adam <[email protected]> Add an initial device tree for Wiko PULP 4G. Includes support for: - UART - USB (no OTG) - Internal storage - MicroSD - Volume keys + Power button - Touchscreen - Backlight - Accelerometer: Invensense MPU6880 - Magnetometer: Asahi Kasei AK09911 - Hall sensor: Rohm BU52021HFV - Proximity sensor - Vibrator - Earpiece - Microphone 1 - Headphones - Wifi - Bluetooth - GPU
Signed-off-by: Paul Adam <[email protected]> --- arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/msm8916-wiko-chuppito.dts | 371 +++++++++++++++++++++ 2 files changed, 372 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index f80b5d9cf1e8..5a3a9a823503 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -75,6 +75,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-rossa.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-serranove.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-thwc-uf896.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-thwc-ufi001c.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8916-wiko-chuppito.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt86518.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt86528.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt88047.dtb diff --git a/arch/arm64/boot/dts/qcom/msm8916-wiko-chuppito.dts b/arch/arm64/boot/dts/qcom/msm8916-wiko-chuppito.dts new file mode 100644 index 000000000000..9e185c8f8f54 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8916-wiko-chuppito.dts @@ -0,0 +1,371 @@ +// SPDX-License-Identifier: GPL-2.0-only + +/dts-v1/; + +#include "msm8916-pm8916.dtsi" +#include "msm8916-modem-qdsp6.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/pinctrl/qcom,pmic-mpp.h> + +/ { + model = "Wiko Pulp 4G"; + compatible = "wiko,chuppito", "qcom,msm8916"; + chassis-type = "handset"; + + aliases { + mmc0 = &sdhc_1; /* eMMC */ + mmc1 = &sdhc_2; /* SD card */ + serial0 = &blsp_uart2; + }; + + chosen { + stdout-path = "serial0"; + }; + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pm8916_pwm 0 100000>; + brightness-levels = <0 255>; + num-interpolated-steps = <255>; + default-brightness-level = <255>; + enable-gpios = <&tlmm 119 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&button_backlight_default>; + pinctrl-1 = <&button_backlight_off>; + pinctrl-names = "default", "off"; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-0 = <&gpio_keys_default>; + pinctrl-names = "default"; + label = "GPIO Buttons"; + + button-volume-up { + label = "Volume up"; + gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + }; + + gpio-hall-sensor { + compatible = "gpio-keys"; + pinctrl-0 = <&gpio_hall_sensor_default>; + pinctrl-names = "default"; + label = "GPIO Hall Effect Sensor"; + + event-hall-sensor { + label = "Hall Effect Sensor"; + gpios = <&tlmm 117 GPIO_ACTIVE_LOW>; + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + linux,can-disable; + }; + }; + + usb_id: usb-id { + compatible = "linux,extcon-usb-gpio"; + id-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&usb_id_default>; + pinctrl-names = "default"; + }; +}; + +&blsp_uart2 { + status = "okay"; +}; + +&blsp_i2c2 { + status = "okay"; + + magnetometer@c { + compatible = "asahi-kasei,ak09911"; + reg = <0x0c>; + vdd-supply = <&pm8916_l17>; + vid-supply = <&pm8916_l6>; + reset-gpios = <&tlmm 120 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&mag_reset_default>; + pinctrl-1 = <&mag_reset_suspend>; + pinctrl-names = "default", "suspend"; + mount-matrix = "1", "0", "0", + "0", "1", "0", + "0", "0", "1"; + }; + + proximity@48 { + // downstream devicetree only specifies "stk,stk3x1x" + compatible = "sensortek,stk3310"; + reg = <0x48>; + interrupts-extended = <&tlmm 113 IRQ_TYPE_EDGE_FALLING>; + pinctrl-0 = <&proximity_int_default>; + pinctrl-1 = <&proximity_int_suspend>; + pinctrl-names = "default", "suspend"; + }; + + imu@68 { + compatible = "invensense,mpu6880"; + reg = <0x68>; + interrupts-extended = <&tlmm 115 IRQ_TYPE_EDGE_FALLING>; + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l6>; + pinctrl-0 = <&imu_int_default>; + pinctrl-1 = <&imu_int_suspend>; + pinctrl-names = "default", "suspend"; + mount-matrix = "0", "-1", "0", + "-1", "0", "0", + "0", "0", "-1"; + }; +}; + +&blsp_i2c5 { + status = "okay"; + + rmi4@39 { + compatible = "syna,rmi4-i2c"; + reg = <0x39>; + interrupts-extended = <&tlmm 13 IRQ_TYPE_EDGE_FALLING>; + vdd-supply = <&pm8916_l17>; + vio-supply = <&pm8916_l6>; + pinctrl-0 = <&touchscreen_default>; + pinctrl-1 = <&touchscreen_suspend>; + pinctrl-names = "default", "suspend"; + #address-cells = <1>; + #size-cells = <0>; + syna,startup-delay-ms = <100>; + syna,reset-delay-ms = <160>; + + rmi4-f01@1 { + reg = <0x1>; + syna,nosleep-mode = <1>; + }; + + rmi4-f11@11 { + reg = <0x11>; + syna,sensor-type = <1>; + }; + }; +}; + +// make sure gcc is probed with display disabled. +&gcc { + clocks = <&xo_board>, <&sleep_clk>, <0>, <0>, <0>, <0>, <0>; +}; + +&gpu { + status = "okay"; +}; + +&mdss { + status = "okay"; +}; + +&mpss_mem { + reg = <0x0 0x86800000 0x0 0x5600000>; +}; + +&pm8916_l6 { + regulator-always-on; +}; + +&pm8916_pwm { + pinctrl-0 = <&pwm_out>; + pinctrl-names = "default"; + status = "okay"; +}; + +&pm8916_resin { + linux,code = <KEY_VOLUMEDOWN>; + status = "okay"; +}; + +&pm8916_rpm_regulators { + pm8916_l17: l17 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + }; +}; + +&pm8916_vib { + status = "okay"; +}; + +&sdhc_1 { + status = "okay"; +}; + +&sdhc_2 { + pinctrl-0 = <&sdc2_default>, <&sdc2_cd_default>; + pinctrl-1 = <&sdc2_sleep>, <&sdc2_cd_default>; + pinctrl-names = "default", "sleep"; + cd-gpios = <&tlmm 38 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&sound { + audio-routing = + "AMIC1", "MIC BIAS Internal1", + "AMIC2", "MIC BIAS Internal2", + "AMIC3", "MIC BIAS Internal1"; +}; + +&usb { + extcon = <&usb_id>, <&usb_id>; + status = "okay"; +}; + +&usb_hs_phy { + extcon = <&usb_id>; +}; + +&venus { + status = "okay"; +}; + +&venus_mem { + status = "okay"; +}; + +&wcnss { + status = "okay"; +}; + +&wcnss_iris { + compatible = "qcom,wcn3620"; +}; + +&wcnss_mem { + status = "okay"; +}; + +&tlmm { + button_backlight_default: button-backlight-default-state { + pins = "gpio119"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + button_backlight_off: button-backlight-off-state { + pins = "gpio119"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + output-low; + }; + + gpio_keys_default: gpio-keys-default-state { + pins = "gpio107"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + + gpio_hall_sensor_default: gpio-hall-sensor-default-state { + pins = "gpio117"; + function = "gpio"; + drive-strength = <6>; + bias-pull-up; + }; + + imu_int_default: imu-int-default-state { + pins = "gpio115"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + imu_int_suspend: imu-int-suspend-state { + pins = "gpio115"; + function = "gpio"; + drive-strength = <2>; + }; + + mag_reset_default: mag-reset-default-state { + pins = "gpio120"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + mag_reset_suspend: mag-reset-suspend-state { + pins = "gpio120"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + + proximity_int_default: proximity-int-default-state { + pins = "gpio113"; + function = "gpio"; + drive-strength = <6>; + bias-pull-up; + }; + + proximity_int_suspend: proximity-int-suspend-state { + pins = "gpio113"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + + sdc2_cd_default: sdc2-cd-default-state { + pins = "gpio38"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + touchscreen_default: touchscreen-default-state { + touchscreen-pins { + pins = "gpio13"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + + reset-pins { + pins = "gpio12"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + }; + + touchscreen_suspend: touchscreen-suspend-state { + touchscreen-pins { + pins = "gpio13"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + + reset-pins { + pins = "gpio12"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + }; + + usb_id_default: usb-id-default-state { + pins = "gpio110"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; +}; + +&pm8916_codec { + qcom,hphl-jack-type-normally-open; +}; + +&pm8916_mpps { + pwm_out: mpp4-state { + pins = "mpp4"; + function = "digital"; + power-source = <PM8916_MPP_VPH>; + output-low; + qcom,dtest = <1>; + }; +}; -- 2.52.0
