On Fri, Jul 11, 2014 at 08:57:33PM +0200, Frederic Weisbecker wrote:
> On Fri, Jul 11, 2014 at 11:45:28AM -0700, Paul E. McKenney wrote:
> > On Fri, Jul 11, 2014 at 08:25:43PM +0200, Frederic Weisbecker wrote:
> > > On Fri, Jul 11, 2014 at 01:10:41PM -0500, Christoph Lameter wrote:
> > > > On Tue, 8 Jul 2014, Frederic Weisbecker wrote:
> > > >
> > > > > > I was figuring that a fair number of the kthreads might eventually
> > > > > > be using this, not just for the grace-period kthreads.
> > > > >
> > > > > Ok makes sense. But can we just rename the cpumask to
> > > > > housekeeping_mask?
> > > >
> > > > That would imply that all no-nohz processors are housekeeping? So all
> > > > processors with a tick are housekeeping?
> > >
> > > Well, now that I think about it again, I would really like to keep
> > > housekeeping
> > > to CPU 0 when nohz_full= is passed.
> >
> > When CONFIG_NO_HZ_FULL_SYSIDLE=y, then housekeeping kthreads are bound to
> > CPU 0. However, doing this causes significant slowdowns according to
> > Fengguang's testing, so when CONFIG_NO_HZ_FULL_SYSIDLE=n, I bind the
> > housekeeping kthreads to the set of non-nohz_full CPUs.
>
> But did he see these slowdowns with nohz_full= parameter passed? I doubt he
> tested that. And I'm not sure that people who need full dynticks will run
> the usecases that trigger slowdowns with grace period kthreads.
>
> I also doubt that people will often omit other CPUs than CPU 0 nohz_full=
> range.
Agreed, this is only a problem when people run workloads for which
NO_HZ_FULL is not well-suited. Which is why I settled on designating
the non-nohz_full= CPUs as the housekeeping CPUs -- people wanting to
run general workloads not suited to NO_HZ_FULL probably won't specify
nohz_full=. If they don't, then any CPU can be a housekeeping CPU.
> > > > Could we make that set configurable? Ideally I'd like to have the
> > > > ability
> > > > restrict the housekeeping to one processor.
> > >
> > > Ah, I'm curious about your usecase. But I think we can do that. And we
> > > should.
> > >
> > > In fact I think that Paul could keep affining grace period kthread to CPU > > > 0
> > > for the sole case when we have nohz_full= parameter passed.
> > >
> > > I think the performance issues reported to him refer to
> > > CONFIG_NO_HZ_FULL=y
> > > config without nohz_full= parameter passed. That's the most important to
> > > address.
> > >
> > > Optimizing the "nohz_full= passed" case is probably not very useful and
> > > worse
> > > it complicate things a lot.
> > >
> > > What do you think Paul? Can we simplify things that way? I'm pretty sure
> > > that
> > > nobody cares about optimizing the nohz_full= case. That would really
> > > simplify
> > > things to stick to CPU 0.
> >
> > When we have CONFIG_NO_HZ_FULL_SYSIDLE=y, agreed. In that case, having
> > housekeeping CPUs on CPUs other than CPU 0 means that you never reach
> > full-system-idle state.
>
> That said I expect CONFIG_NO_HZ_FULL_SYSIDLE=y to be always enable for those
> who run NO_HZ_FULL in the long run.
Hmmm... That probably means that we need boot-time parameters to
make sysidle detection really happen. Otherwise, many users will
get a nasty surprise once CONFIG_NO_HZ_FULL_SYSIDLE=y is enabled on
systems that really aren't running HPC or RT workloads.
I suppose that I could confine SYSIDLE's attention to the nohz_full=
CPUs -- that might actually make things work nicely in all cases with
no configuration of any sort required. I will need to give this some
thought.
> > But in other cases, we appear to need more than one housekeeping CPU.
> > This is especially the case when people run general workloads on systems
> > that have NO_HZ_FULL=y, which appears to be a significant fraction of
> > the systems these days.
>
> Yeah NO_HZ_FULL=y is likely to be enabled in many distros. But you know the
> amount of nohz_full= users.
Indeed! ;-)
Thanx, Paul
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
