On Mon, Oct 13, 2014 at 02:14:05PM -0500, Felipe Balbi wrote:
> On Mon, Oct 13, 2014 at 11:23:59AM -0700, David Cohen wrote:
> > Even if a gpio pin is set to output, we still need to set INPUT_EN bit
> 
> here you say you're setting that bit.
> 
> > to be able to read its value. Without this change, we'll always read low
> > level state.
> > 
> > Cc: <sta...@vger.kernel.org> # v3.14+
> > Signed-off-by: David Cohen <david.a.co...@linux.intel.com>
> > ---
> > 
> > Hi,
> > 
> > I'm resending same v1 patch but now copying linux stable and linux gpio.
> > This patch is meant for all linux stable trees >= v3.14.
> > 
> > Br, David
> > ---
> > 
> >  drivers/pinctrl/pinctrl-baytrail.c | 2 +-
> >  1 file changed, 1 insertion(+), 1 deletion(-)
> > 
> > diff --git a/drivers/pinctrl/pinctrl-baytrail.c 
> > b/drivers/pinctrl/pinctrl-baytrail.c
> > index e12e5b07f6d7..c23d8ded936d 100644
> > --- a/drivers/pinctrl/pinctrl-baytrail.c
> > +++ b/drivers/pinctrl/pinctrl-baytrail.c
> > @@ -318,7 +318,7 @@ static int byt_gpio_direction_output(struct gpio_chip 
> > *chip,
> >             "Potential Error: Setting GPIO with direct_irq_en to output");
> >  
> >     reg_val = readl(reg) | BYT_DIR_MASK;
> > -   reg_val &= ~BYT_OUTPUT_EN;
> > +   reg_val &= ~(BYT_OUTPUT_EN | BYT_INPUT_EN);
> 
> but code is clearing it. Also, you're not patching byt_gpio_get(), so
> you can't be 'reading its value' either. Quite frankly, this looks very
> fishy to me. Comments on BYT_OUTPUT_EN and BYT_INPUT_EN states that
> those bits are active low, meaning that clearing them enables that
> particular feature.
> 
> How can you enable a pin to be both OUTPUT and INPUT ? Look like what
> you really want is:
> 
> diff --git a/drivers/pinctrl/pinctrl-baytrail.c 
> b/drivers/pinctrl/pinctrl-baytrail.c
> index e12e5b0..69f882d 100644
> --- a/drivers/pinctrl/pinctrl-baytrail.c
> +++ b/drivers/pinctrl/pinctrl-baytrail.c
> @@ -290,6 +290,7 @@ static int byt_gpio_direction_input(struct gpio_chip 
> *chip, unsigned offset)
>  
>       value = readl(reg) | BYT_DIR_MASK;
>       value &= ~BYT_INPUT_EN;         /* active low */
> +     value |= BYT_OUTPUT_EN;         /* disable output */
>       writel(value, reg);
>  
>       spin_unlock_irqrestore(&vg->lock, flags);
> @@ -319,6 +320,7 @@ static int byt_gpio_direction_output(struct gpio_chip 
> *chip,
>  
>       reg_val = readl(reg) | BYT_DIR_MASK;
>       reg_val &= ~BYT_OUTPUT_EN;
> +     value |= BYT_INPUT_EN;          /* disable input */
>  
>       if (value)
>               writel(reg_val | BYT_LEVEL, reg);
> 
> completely untested however. Care to further explain why clearing both
> bits - thus enabling both INPUT and OUTPUT - is correct ?

Actually I really meant what I sent, but perhaps I misspoke during
explanation. We need to clear the bit to enable the functionality.

!BYT_INPUT_EN allows us to read the value. !BYT_OUTPUT_EN allows us to
set a value. If we want to set a value (acting as output) and still be
able to read via sysfs, we need to set both functionality (i.e. clear
both bits).

I'll resend the patch with a better comment.

Br, David

> 
> -- 
> balbi


--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Reply via email to