From: Flora Fu <[email protected]> This adds support for the regulators on the MediaTek MT6397 Multifunction device.
Signed-off-by: Flora Fu, MediaTek Signed-off-by: Sascha Hauer <[email protected]> Cc: Liam Girdwood <[email protected]> Cc: Mark Brown <[email protected]> --- Documentation/devicetree/bindings/mfd/mt6397.txt | 41 ++- .../bindings/regulator/mt6397-regulator.txt | 217 ++++++++++++++ drivers/regulator/Kconfig | 9 + drivers/regulator/Makefile | 1 + drivers/regulator/mt6397-regulator.c | 332 +++++++++++++++++++++ include/linux/regulator/mt6397-regulator.h | 49 +++ 6 files changed, 626 insertions(+), 23 deletions(-) create mode 100644 Documentation/devicetree/bindings/regulator/mt6397-regulator.txt create mode 100644 drivers/regulator/mt6397-regulator.c create mode 100644 include/linux/regulator/mt6397-regulator.h diff --git a/Documentation/devicetree/bindings/mfd/mt6397.txt b/Documentation/devicetree/bindings/mfd/mt6397.txt index 64ef408..25b40a6 100644 --- a/Documentation/devicetree/bindings/mfd/mt6397.txt +++ b/Documentation/devicetree/bindings/mfd/mt6397.txt @@ -10,33 +10,34 @@ MT6397 is a multifunction device with the following sub modules: It is interfaced to host controller using SPI interface by a proprietary hardware called PMIC wrapper or pwrap. MT6397 MFD is a child device of pwrap. See the following for pwarp node definitions: -Documentation/devicetree/bindings/soc/mediatek,mt8135-pwrap.txt +Documentation/devicetree/bindings/soc/pwrap.txt This document describes the binding for mfd device and its sub module. Required properties: compatible: "mediatek,mt6397" -Optional properties: -- codec: Audio codec -- pinctrl: GPIO in mt6397 -- rtc: RTC -- clock: clocks in mt6397 -- regulators: regulators in mt6397 +Optional subnodes: + +- rtc: + Required properties: + - compatible: "mediatek,mt6397-rtc", +- regulators + Required properties: + - compatible: "mediatek,mt6397-regulator", + see Documentation/devicetree/bindings/regulator/mt6397-regulator.txt +- codec + Required properties: + - compatible: "mediatek,mt6397-codec", +- clk + Required properties: + - compatible: "mediatek,mt6397-clk", Example: pwrap: pwrap@1000f000 { compatible = "mediatek,mt8135-pwrap"; - reg = <0 0x1000f000 0 0x1000>, - <0 0x11017000 0 0x1000>; - reg-names = "pwrap-base", "pwrap-bridge-base"; - interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>; - resets = <&infrarst MT8135_INFRA_PMIC_WRAP_RST>, - <&perirst MT8135_PERI_PWRAP_BRIDGE_SW_RST>; - reset-names = "infra-pwrap-rst", - "peri-pwrap-bridge-rst"; - clocks = <&pmicspi_sel>, <&clk26m>; - clock-names = "pmicspi-sel", "pmicspi-parent"; + + ... pmic { compatible = "mediatek,mt6397"; @@ -45,12 +46,6 @@ Example: compatible = "mediatek,mt6397-codec"; }; - pinctrl@0x0000C000 { - compatible = "mediatek,mt6397-pinctrl"; - reg = <0 0x0000C000 0 0x0108>; - gpio-controller; - }; - mt6397regulator: mt6397regulator { compatible = "mediatek,mt6397-regulator"; diff --git a/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt b/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt new file mode 100644 index 0000000..a42b1d6 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt @@ -0,0 +1,217 @@ +Mediatek MT6397 Regulator Driver + +Required properties: +- compatible: "mediatek,mt6397-regulator" +- mt6397regulator: List of regulators provided by this controller. It is named + according to its regulator type, buck_<name> and ldo_<name>. + The definition for each of these nodes is defined using the standard binding + for regulators at Documentation/devicetree/bindings/regulator/regulator.txt. + +The valid names for regulators are:: +BUCK: + buck_vpca15, buck_vpca7, buck_vsramca15, buck_vsramca7, buck_vcore, buck_vgpu, + buck_vdrm, buck_vio18 +LDO: + ldo_vtcxo, ldo_va28, ldo_vcama, ldo_vio28, ldo_vusb, ldo_vmc, ldo_vmch, + ldo_vemc3v3, ldo_vgp1, ldo_vgp2, ldo_vgp3, ldo_vgp4, ldo_vgp5, ldo_vgp6, + ldo_vibr + +Example: + pmic { + compatible = "mediatek,mt6397"; + + mt6397regulator: mt6397regulator { + compatible = "mediatek,mt6397-regulator"; + + mt6397_vpca15_reg: buck_vpca15 { + regulator-compatible = "buck_vpca15"; + regulator-name = "vpca15"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <200>; + }; + + mt6397_vpca7_reg: buck_vpca7 { + regulator-compatible = "buck_vpca7"; + regulator-name = "vpca7"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + }; + + mt6397_vsramca15_reg: buck_vsramca15 { + regulator-compatible = "buck_vsramca15"; + regulator-name = "vsramca15"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + + }; + + mt6397_vsramca7_reg: buck_vsramca7 { + regulator-compatible = "buck_vsramca7"; + regulator-name = "vsramca7"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + + }; + + mt6397_vcore_reg: buck_vcore { + regulator-compatible = "buck_vcore"; + regulator-name = "vcore"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + }; + + mt6397_vgpu_reg: buck_vgpu { + regulator-compatible = "buck_vgpu"; + regulator-name = "vgpu"; + regulator-min-microvolt = < 700000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + }; + + mt6397_vdrm_reg: buck_vdrm { + regulator-compatible = "buck_vdrm"; + regulator-name = "vdrm"; + regulator-min-microvolt = < 800000>; + regulator-max-microvolt = <1400000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <500>; + }; + + mt6397_vio18_reg: buck_vio18 { + regulator-compatible = "buck_vio18"; + regulator-name = "vio18"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2120000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <500>; + }; + + mt6397_vtcxo_reg: ldo_vtcxo { + regulator-compatible = "ldo_vtcxo"; + regulator-name = "vtcxo"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <90>; + }; + + mt6397_va28_reg: ldo_va28 { + regulator-compatible = "ldo_va28"; + regulator-name = "va28"; + /* fixed output 2.8 V */ + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vcama_reg: ldo_vcama { + regulator-compatible = "ldo_vcama"; + regulator-name = "vcama"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vio28_reg: ldo_vio28 { + regulator-compatible = "ldo_vio28"; + regulator-name = "vio28"; + /* fixed output 2.8 V */ + regulator-enable-ramp-delay = <240>; + }; + + mt6397_usb_reg: ldo_vusb { + regulator-compatible = "ldo_vusb"; + regulator-name = "vusb"; + /* fixed output 3.3 V */ + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vmc_reg: ldo_vmc { + regulator-compatible = "ldo_vmc"; + regulator-name = "vmc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vmch_reg: ldo_vmch { + regulator-compatible = "ldo_vmch"; + regulator-name = "vmch"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vemc_3v3_reg: ldo_vemc3v3 { + regulator-compatible = "ldo_vemc3v3"; + regulator-name = "vemc_3v3"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp1_reg: ldo_vgp1 { + regulator-compatible = "ldo_vgp1"; + regulator-name = "vcamd"; + regulator-min-microvolt = <1220000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <240>; + }; + + mt6397_vgp2_reg: ldo_vgp2 { + egulator-compatible = "ldo_vgp2"; + regulator-name = "vcamio"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp3_reg: ldo_vgp3 { + regulator-compatible = "ldo_vgp3"; + regulator-name = "vcamaf"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp4_reg: ldo_vgp4 { + regulator-compatible = "ldo_vgp4"; + regulator-name = "vgp4"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp5_reg: ldo_vgp5 { + regulator-compatible = "ldo_vgp5"; + regulator-name = "vgp5"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp6_reg: ldo_vgp6 { + regulator-compatible = "ldo_vgp6"; + regulator-name = "vgp6"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vibr_reg: ldo_vibr { + regulator-compatible = "ldo_vibr"; + regulator-name = "vibr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + }; + }; diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig index c3a60b5..f622d06 100644 --- a/drivers/regulator/Kconfig +++ b/drivers/regulator/Kconfig @@ -433,6 +433,15 @@ config REGULATOR_MC13892 Say y here to support the regulators found on the Freescale MC13892 PMIC. +config REGULATOR_MT6397 + tristate "MediaTek MT6397 PMIC" + depends on MFD_MT6397 + help + Say y here to select this option to enable the power regulator of + MediaTek MT6397 PMIC. + This driver supports the control of different power rails of device + through regulator interface. + config REGULATOR_PALMAS tristate "TI Palmas PMIC Regulators" depends on MFD_PALMAS diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile index 1f28ebf..1a0fbc3 100644 --- a/drivers/regulator/Makefile +++ b/drivers/regulator/Makefile @@ -58,6 +58,7 @@ obj-$(CONFIG_REGULATOR_MAX77802) += max77802.o obj-$(CONFIG_REGULATOR_MC13783) += mc13783-regulator.o obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o obj-$(CONFIG_REGULATOR_MC13XXX_CORE) += mc13xxx-regulator-core.o +obj-$(CONFIG_REGULATOR_MT6397) += mt6397-regulator.o obj-$(CONFIG_REGULATOR_QCOM_RPM) += qcom_rpm-regulator.o obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o diff --git a/drivers/regulator/mt6397-regulator.c b/drivers/regulator/mt6397-regulator.c new file mode 100644 index 0000000..a5b2f47 --- /dev/null +++ b/drivers/regulator/mt6397-regulator.c @@ -0,0 +1,332 @@ +/* + * Copyright (c) 2014 MediaTek Inc. + * Author: Flora Fu <[email protected]> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/mfd/mt6397/core.h> +#include <linux/mfd/mt6397/registers.h> +#include <linux/regulator/driver.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/mt6397-regulator.h> +#include <linux/regulator/of_regulator.h> + +/* + * MT6397 regulators' information + * + * @desc: standard fields of regulator description. + * @qi: Mask for query enable signal status of regulators + * @vselon_reg: Register sections for hardware control mode of bucks + * @vselctrl_reg: Register for controlling the buck control mode. + * @vselctrl_mask: Mask for query buck's voltage control mode. + */ +struct mt6397_regulator_info { + struct regulator_desc desc; + u32 qi; + u32 vselon_reg; + u32 vselctrl_reg; + u32 vselctrl_mask; +}; + +#define MT6397_BUCK(match, vreg, min, max, step, volt_ranges, enreg, \ + vosel, vosel_mask, voselon, vosel_ctrl) \ +[MT6397_ID_##vreg] = { \ + .desc = { \ + .name = #vreg, \ + .of_match = of_match_ptr(match), \ + .ops = &mt6397_volt_range_ops, \ + .type = REGULATOR_VOLTAGE, \ + .id = MT6397_ID_##vreg, \ + .owner = THIS_MODULE, \ + .n_voltages = (max - min)/step + 1, \ + .linear_ranges = volt_ranges, \ + .n_linear_ranges = ARRAY_SIZE(volt_ranges), \ + .vsel_reg = vosel, \ + .vsel_mask = vosel_mask, \ + .enable_reg = enreg, \ + .enable_mask = BIT(0), \ + }, \ + .qi = BIT(13), \ + .vselon_reg = voselon, \ + .vselctrl_reg = vosel_ctrl, \ + .vselctrl_mask = BIT(1), \ +} + +#define MT6397_LDO(match, vreg, ldo_volt_table, enreg, enbit, vosel, \ + vosel_mask) \ +[MT6397_ID_##vreg] = { \ + .desc = { \ + .name = #vreg, \ + .of_match = of_match_ptr(match), \ + .ops = &mt6397_volt_table_ops, \ + .type = REGULATOR_VOLTAGE, \ + .id = MT6397_ID_##vreg, \ + .owner = THIS_MODULE, \ + .n_voltages = ARRAY_SIZE(ldo_volt_table), \ + .volt_table = ldo_volt_table, \ + .vsel_reg = vosel, \ + .vsel_mask = vosel_mask, \ + .enable_reg = enreg, \ + .enable_mask = BIT(enbit), \ + }, \ + .qi = BIT(15), \ +} + +#define MT6397_REG_FIXED(match, vreg, enreg, enbit, volt) \ +[MT6397_ID_##vreg] = { \ + .desc = { \ + .name = #vreg, \ + .of_match = of_match_ptr(match), \ + .ops = &mt6397_volt_fixed_ops, \ + .type = REGULATOR_VOLTAGE, \ + .id = MT6397_ID_##vreg, \ + .owner = THIS_MODULE, \ + .n_voltages = 1, \ + .enable_reg = enreg, \ + .enable_mask = BIT(enbit), \ + .min_uV = volt, \ + }, \ + .qi = BIT(15), \ +} + +static const struct regulator_linear_range buck_volt_range1[] = { + REGULATOR_LINEAR_RANGE(700000, 0, 0x7f, 6250), +}; + +static const struct regulator_linear_range buck_volt_range2[] = { + REGULATOR_LINEAR_RANGE(800000, 0, 0x7f, 6250), +}; + +static const struct regulator_linear_range buck_volt_range3[] = { + REGULATOR_LINEAR_RANGE(1500000, 0, 0x1f, 20000), +}; + +static const u32 ldo_volt_table1[] = { + 1500000, 1800000, 2500000, 2800000, +}; + +static const u32 ldo_volt_table2[] = { + 1800000, 3300000, +}; + +static const u32 ldo_volt_table3[] = { + 3000000, 3300000, +}; + +static const u32 ldo_volt_table4[] = { + 1220000, 1300000, 1500000, 1800000, 2500000, 2800000, 3000000, 3300000, +}; + +static const u32 ldo_volt_table5[] = { + 1200000, 1300000, 1500000, 1800000, 2500000, 2800000, 3000000, 3300000, +}; + +static const u32 ldo_volt_table5_v2[] = { + 1200000, 1000000, 1500000, 1800000, 2500000, 2800000, 3000000, 3300000, +}; + +static const u32 ldo_volt_table6[] = { + 1200000, 1300000, 1500000, 1800000, 2500000, 2800000, 3000000, 2000000, +}; + +static const u32 ldo_volt_table7[] = { + 1300000, 1500000, 1800000, 2000000, 2500000, 2800000, 3000000, 3300000, +}; + +static int mt6397_get_status(struct regulator_dev *rdev) +{ + int ret; + u32 regval; + struct mt6397_regulator_info *info = rdev_get_drvdata(rdev); + + ret = regmap_read(rdev->regmap, info->desc.enable_reg, ®val); + if (ret != 0) { + dev_err(&rdev->dev, "Failed to get enable reg: %d\n", ret); + return ret; + } + + return (regval & info->qi) ? REGULATOR_STATUS_ON : REGULATOR_STATUS_OFF; +} + +static struct regulator_ops mt6397_volt_range_ops = { + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_time_sel = regulator_set_voltage_time_sel, + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, + .get_status = mt6397_get_status, +}; + +static struct regulator_ops mt6397_volt_table_ops = { + .list_voltage = regulator_list_voltage_table, + .map_voltage = regulator_map_voltage_iterate, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_time_sel = regulator_set_voltage_time_sel, + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, + .get_status = mt6397_get_status, +}; + +static struct regulator_ops mt6397_volt_fixed_ops = { + .list_voltage = regulator_list_voltage_linear, + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, + .get_status = mt6397_get_status, +}; + +/* The array is indexed by id(MT6397_ID_XXX) */ +static struct mt6397_regulator_info mt6397_regulators[] = { + MT6397_BUCK("buck_vpca15", VPCA15, 700000, 1493750, 6250, + buck_volt_range1, MT6397_VCA15_CON7, MT6397_VCA15_CON9, 0x7f, + MT6397_VCA15_CON10, MT6397_VCA15_CON5), + MT6397_BUCK("buck_vpca7", VPCA7, 700000, 1493750, 6250, + buck_volt_range1, MT6397_VPCA7_CON7, MT6397_VPCA7_CON9, 0x7f, + MT6397_VPCA7_CON10, MT6397_VPCA7_CON5), + MT6397_BUCK("buck_vsramca15", VSRAMCA15, 700000, 1493750, 6250, + buck_volt_range1, MT6397_VSRMCA15_CON7, MT6397_VSRMCA15_CON9, + 0x7f, MT6397_VSRMCA15_CON10, MT6397_VSRMCA15_CON5), + MT6397_BUCK("buck_vsramca7", VSRAMCA7, 700000, 1493750, 6250, + buck_volt_range1, MT6397_VSRMCA7_CON7, MT6397_VSRMCA7_CON9, + 0x7f, MT6397_VSRMCA7_CON10, MT6397_VSRMCA7_CON5), + MT6397_BUCK("buck_vcore", VCORE, 700000, 1493750, 6250, + buck_volt_range1, MT6397_VCORE_CON7, MT6397_VCORE_CON9, 0x7f, + MT6397_VCORE_CON10, MT6397_VCORE_CON5), + MT6397_BUCK("buck_vgpu", VGPU, 700000, 1493750, 6250, buck_volt_range1, + MT6397_VGPU_CON7, MT6397_VGPU_CON9, 0x7f, + MT6397_VGPU_CON10, MT6397_VGPU_CON5), + MT6397_BUCK("buck_vdrm", VDRM, 800000, 1593750, 6250, buck_volt_range2, + MT6397_VDRM_CON7, MT6397_VDRM_CON9, 0x7f, + MT6397_VDRM_CON10, MT6397_VDRM_CON5), + MT6397_BUCK("buck_vio18", VIO18, 1500000, 2120000, 20000, + buck_volt_range3, MT6397_VIO18_CON7, MT6397_VIO18_CON9, 0x1f, + MT6397_VIO18_CON10, MT6397_VIO18_CON5), + MT6397_REG_FIXED("ldo_vtcxo", VTCXO, MT6397_ANALDO_CON0, 10, 2800000), + MT6397_REG_FIXED("ldo_va28", VA28, MT6397_ANALDO_CON1, 14, 2800000), + MT6397_LDO("ldo_vcama", VCAMA, ldo_volt_table1, + MT6397_ANALDO_CON2, 15, MT6397_ANALDO_CON6, 0xC0), + MT6397_REG_FIXED("ldo_vio28", VIO28, MT6397_DIGLDO_CON0, 14, 2800000), + MT6397_REG_FIXED("ldo_vusb", VUSB, MT6397_DIGLDO_CON1, 14, 3300000), + MT6397_LDO("ldo_vmc", VMC, ldo_volt_table2, + MT6397_DIGLDO_CON2, 12, MT6397_DIGLDO_CON29, 0x10), + MT6397_LDO("ldo_vmch", VMCH, ldo_volt_table3, + MT6397_DIGLDO_CON3, 14, MT6397_DIGLDO_CON17, 0x80), + MT6397_LDO("ldo_vemc3v3", VEMC3V3, ldo_volt_table3, + MT6397_DIGLDO_CON4, 14, MT6397_DIGLDO_CON18, 0x10), + MT6397_LDO("ldo_vgp1", VGP1, ldo_volt_table4, + MT6397_DIGLDO_CON5, 15, MT6397_DIGLDO_CON19, 0xE0), + MT6397_LDO("ldo_vgp2", VGP2, ldo_volt_table5, + MT6397_DIGLDO_CON6, 15, MT6397_DIGLDO_CON20, 0xE0), + MT6397_LDO("ldo_vgp3", VGP3, ldo_volt_table5, + MT6397_DIGLDO_CON7, 15, MT6397_DIGLDO_CON21, 0xE0), + MT6397_LDO("ldo_vgp4", VGP4, ldo_volt_table5, + MT6397_DIGLDO_CON8, 15, MT6397_DIGLDO_CON22, 0xE0), + MT6397_LDO("ldo_vgp5", VGP5, ldo_volt_table6, + MT6397_DIGLDO_CON9, 15, MT6397_DIGLDO_CON23, 0xE0), + MT6397_LDO("ldo_vgp6", VGP6, ldo_volt_table5, + MT6397_DIGLDO_CON10, 15, MT6397_DIGLDO_CON33, 0xE0), + MT6397_LDO("ldo_vibr", VIBR, ldo_volt_table7, + MT6397_DIGLDO_CON24, 15, MT6397_DIGLDO_CON25, 0xE00), +}; + +static int mt6397_set_buck_vosel_reg(struct platform_device *pdev) +{ + struct mt6397_chip *mt6397 = dev_get_drvdata(pdev->dev.parent); + int i; + u32 regval; + + for (i = 0; i < MT6397_MAX_REGULATOR; i++) { + if (mt6397_regulators[i].vselctrl_reg) { + if (regmap_read(mt6397->regmap, + mt6397_regulators[i].vselctrl_reg, + ®val) < 0) { + dev_err(&pdev->dev, + "Failed to read buck ctrl\n"); + return -EIO; + } + + if (regval & mt6397_regulators[i].vselctrl_mask) { + mt6397_regulators[i].desc.vsel_reg = + mt6397_regulators[i].vselon_reg; + } + } + } + + return 0; +} + +static int mt6397_regulator_probe(struct platform_device *pdev) +{ + struct mt6397_chip *mt6397 = dev_get_drvdata(pdev->dev.parent); + struct regulator_config config = {}; + struct regulator_dev *rdev; + int i; + u32 reg_value, version; + + /* Query buck controller to select activated voltage register part */ + if (mt6397_set_buck_vosel_reg(pdev)) + return -EIO; + + /* Read PMIC chip revision to update constraints and voltage table */ + if (regmap_read(mt6397->regmap, MT6397_CID, ®_value) < 0) { + dev_err(&pdev->dev, "Failed to read Chip ID\n"); + return -EIO; + } + dev_info(&pdev->dev, "Chip ID = 0x%x\n", reg_value); + + version = (reg_value & 0xFF); + switch (version) { + case MT6397_REGULATOR_ID91: + mt6397_regulators[MT6397_ID_VGP2].desc.volt_table = + ldo_volt_table5_v2; + break; + default: + break; + } + + for (i = 0; i < MT6397_MAX_REGULATOR; i++) { + config.dev = &pdev->dev; + config.driver_data = &mt6397_regulators[i]; + config.regmap = mt6397->regmap; + rdev = devm_regulator_register(&pdev->dev, + &mt6397_regulators[i].desc, &config); + if (IS_ERR(rdev)) { + dev_err(&pdev->dev, "failed to register %s\n", + mt6397_regulators[i].desc.name); + return PTR_ERR(rdev); + } + } + + return 0; +} + +static struct platform_driver mt6397_regulator_driver = { + .driver = { + .name = "mt6397-regulator", + }, + .probe = mt6397_regulator_probe, +}; + +module_platform_driver(mt6397_regulator_driver); + +MODULE_AUTHOR("Flora Fu <[email protected]>"); +MODULE_DESCRIPTION("Regulator Driver for MediaTek MT6397 PMIC"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:mt6397-regulator"); diff --git a/include/linux/regulator/mt6397-regulator.h b/include/linux/regulator/mt6397-regulator.h new file mode 100644 index 0000000..30cc596 --- /dev/null +++ b/include/linux/regulator/mt6397-regulator.h @@ -0,0 +1,49 @@ +/* + * Copyright (c) 2014 MediaTek Inc. + * Author: Flora Fu <[email protected]> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef __LINUX_REGULATOR_MT6397_H +#define __LINUX_REGULATOR_MT6397_H + +enum { + MT6397_ID_VPCA15 = 0, + MT6397_ID_VPCA7, + MT6397_ID_VSRAMCA15, + MT6397_ID_VSRAMCA7, + MT6397_ID_VCORE, + MT6397_ID_VGPU, + MT6397_ID_VDRM, + MT6397_ID_VIO18 = 7, + MT6397_ID_VTCXO, + MT6397_ID_VA28, + MT6397_ID_VCAMA, + MT6397_ID_VIO28, + MT6397_ID_VUSB, + MT6397_ID_VMC, + MT6397_ID_VMCH, + MT6397_ID_VEMC3V3, + MT6397_ID_VGP1, + MT6397_ID_VGP2, + MT6397_ID_VGP3, + MT6397_ID_VGP4, + MT6397_ID_VGP5, + MT6397_ID_VGP6, + MT6397_ID_VIBR, + MT6397_ID_RG_MAX, +}; + +#define MT6397_MAX_REGULATOR MT6397_ID_RG_MAX +#define MT6397_REGULATOR_ID97 0x97 +#define MT6397_REGULATOR_ID91 0x91 + +#endif /* __LINUX_REGULATOR_MT6397_H */ -- 2.1.4 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
