The patch regulator: max8973: add support to configure ETR based on rail load
has been applied to the regulator tree at git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted. You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed. If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced. Please add any relevant lists and maintainers to the CCs when replying to this mail. Thanks, Mark >From ffaab99184a2c8b592bba85d8e4da708c65b4cc1 Mon Sep 17 00:00:00 2001 From: Laxman Dewangan <[email protected]> Date: Wed, 1 Jul 2015 18:31:44 +0530 Subject: [PATCH] regulator: max8973: add support to configure ETR based on rail load Add support to configure Enhanced Transient Response Enable (ETR) and Sensitivity Selection based on maximum current i.e. expected load on that rail. Maxim recommended as: - Enable ETR with high sensitivity (75mV/us) for 0 to 9A expected loads, - Enable ETR with low sensitivity (150mV/us) for 9A to 12A expected loads. - Disable ETR for expected load > 12A. These recommendation will be configured for MAX77621 when maximum load is provided through regulator constraint for maximum current from platform. Signed-off-by: Laxman Dewangan <[email protected]> Signed-off-by: Mark Brown <[email protected]> --- drivers/regulator/max8973-regulator.c | 52 +++++++++++++++++++++++++++++++++++ 1 file changed, 52 insertions(+) diff --git a/drivers/regulator/max8973-regulator.c b/drivers/regulator/max8973-regulator.c index a8fd7f4..f673659 100644 --- a/drivers/regulator/max8973-regulator.c +++ b/drivers/regulator/max8973-regulator.c @@ -75,6 +75,7 @@ #define MAX8973_DISCH_ENBABLE BIT(5) #define MAX8973_FT_ENABLE BIT(4) +#define MAX8973_CKKADV_TRIP_MASK 0xC #define MAX8973_CKKADV_TRIP_DISABLE 0xC #define MAX8973_CKKADV_TRIP_75mV_PER_US 0x0 #define MAX8973_CKKADV_TRIP_150mV_PER_US 0x4 @@ -282,6 +283,55 @@ static int max8973_set_ramp_delay(struct regulator_dev *rdev, return ret; } +static int max8973_set_current_limit(struct regulator_dev *rdev, + int min_ua, int max_ua) +{ + struct max8973_chip *max = rdev_get_drvdata(rdev); + unsigned int val; + int ret; + + if (max_ua <= 9000000) + val = MAX8973_CKKADV_TRIP_75mV_PER_US; + else if (max_ua <= 12000000) + val = MAX8973_CKKADV_TRIP_150mV_PER_US; + else + val = MAX8973_CKKADV_TRIP_DISABLE; + + ret = regmap_update_bits(max->regmap, MAX8973_CONTROL2, + MAX8973_CKKADV_TRIP_MASK, val); + if (ret < 0) { + dev_err(max->dev, "register %d update failed: %d\n", + MAX8973_CONTROL2, ret); + return ret; + } + return 0; +} + +static int max8973_get_current_limit(struct regulator_dev *rdev) +{ + struct max8973_chip *max = rdev_get_drvdata(rdev); + unsigned int control2; + int ret; + + ret = regmap_read(max->regmap, MAX8973_CONTROL2, &control2); + if (ret < 0) { + dev_err(max->dev, "register %d read failed: %d\n", + MAX8973_CONTROL2, ret); + return ret; + } + switch (control2 & MAX8973_CKKADV_TRIP_MASK) { + case MAX8973_CKKADV_TRIP_DISABLE: + return 15000000; + case MAX8973_CKKADV_TRIP_150mV_PER_US: + return 12000000; + case MAX8973_CKKADV_TRIP_75mV_PER_US: + return 9000000; + default: + break; + } + return 9000000; +} + static const struct regulator_ops max8973_dcdc_ops = { .get_voltage_sel = max8973_dcdc_get_voltage_sel, .set_voltage_sel = max8973_dcdc_set_voltage_sel, @@ -632,6 +682,8 @@ static int max8973_probe(struct i2c_client *client, max->ops.enable = regulator_enable_regmap; max->ops.disable = regulator_disable_regmap; max->ops.is_enabled = regulator_is_enabled_regmap; + max->ops.set_current_limit = max8973_set_current_limit; + max->ops.get_current_limit = max8973_get_current_limit; break; default: break; -- 2.1.4 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
